Last Modified: 01-30-2024 6.11:8.1.0 Doc ID: RM100000001EADG
Model Year Start: 2019 Model: RAV4 Prod Date Range: [11/2018 - 02/2019]
Title: BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster): DATA LIST / ACTIVE TEST; 2019 MY RAV4 RAV4 HV [11/2018 - 02/2019]

DATA LIST / ACTIVE TEST

DATA LIST

HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

(a) Warm up the engine.

(b) Turn the power switch off.

(c) Connect the Techstream to the DLC3.

(d) Turn the power switch on (IG).

(e) Turn the Techstream on.

(f) Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.

(g) According to the display on the Techstream, read the Data List.

Chassis > ABS/VSC/TRAC > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

ABS Warning Light

ABS warning light

ON or OFF

ON: Warning light on

OFF: Warning light off

-

Brake Warning Light

Brake warning light / red (malfunction)

ON or OFF

ON: Warning light on

OFF: Warning light off

-

ECB Warning Light

Brake warning light / yellow (minor malfunction)

ON or OFF

ON: Warning light on

OFF: Warning light off

ECB: Electronically Controlled Brake System

Buzzer

Meter buzzer

ON or OFF

ON: Buzzer on

OFF: Buzzer off

-

Stop Light SW

Stop light switch assembly

ON or OFF

ON: Brake pedal depressed

OFF: Brake pedal released

-

Parking Brake SW

Parking brake switch

ON or OFF

ON: Parking brake applied

OFF: Parking brake released

-

Reservoir Warning SW

Brake fluid level warning switch

ON or OFF

ON: Reservoir level low

OFF: Reservoir level normal

-

Main Idle SW

Main idle switch

ON or OFF

ON: Accelerator pedal released

OFF: Accelerator pedal depressed

-

Shift Lever Position

Shift position information

Fail, 1st-6th/B, D/M, P,N or R

Actual shift position

-

Inspection Mode

Inspection mode

Other or Inspect

Other: Normal mode

Inspect: Inspection mode

-

Regulator Pressure Sensor Output

Regulator pressure sensor output

Min.: 0.00 V, Max.: 5.00 V

Brake pedal released: 0.10 to 0.90 V

Reading increases when brake pedal is depressed

Stroke Sensor

Brake pedal stroke sensor assembly

Min.: 0.00 V, Max.: 5.00 V

Brake pedal released: 0.65 to 1.35 V

Reading increases when brake pedal is depressed

Voltage of Stroke Sensor

Voltage of brake pedal stroke sensor assembly

Min.: -2.50 V, Max.: 2.49 V

-

-

Stroke Sensor2

Brake pedal stroke sensor assembly 2

Min.: 0.00 V, Max.: 5.00 V

Brake pedal released: 3.65 to 4.35 V

Reading decreases when brake pedal is depressed

Voltage of Stroke Sensor2

Voltage of brake pedal stroke sensor assembly 2

Min.: -2.50 V, Max.: 2.49 V

-

-

Accumulator Sensor

Accumulator pressure sensor

Min.: 0.00 V, Max.: 5.00 V

Specified value: 2.90 to 4.20 V

When brake fluid is stored in the accumulator: Accumulator pressure changes in accordance with volume of fluid stored in the accumulator

Deceleration Sensor

Acceleration sensor 1

Min.: -18.525 m/s2, Max.: 18.387 m/s2

-

During deceleration/acceleration: Changes continuously

Zero Point of Decele

Memorized zero value

Min.: -25.10 m/s2, Max.: 24.90 m/s2

-

-

Deceleration Sensor2

Acceleration sensor 2

Min.: -18.525 m/s2, Max.: 18.387 m/s2

-

During deceleration/acceleration: Changes continuously

Zero Point of Decele2

Memorized zero value

Min.: -25.10 m/s2, Max.: 24.90 m/s2

-

-

Yaw Rate Sensor

Yaw rate sensor 1

Min.: -128°/s, Max.: 127°/s

Vehicle stationary: 0°/s

Turning right: -128 to 0°/s

Turning left: 0 to 127°/s

-

Zero Point of Yaw Rate

Memorized zero value

Min.: -128°, Max.: 127°

-

After completing zero point calibration: 0°

Yaw Rate Sensor2

Yaw rate sensor 2

Min.: -128°/s, Max.: 127°/s

Vehicle stationary: 0°/s

Turning right: -128 to 0°/s

Turning left: 0 to 127°/s

-

Zero Point of Yaw Rate2

Memorized zero value

Min.: -128°/s, Max.: 127°/s

-

After completing zero point calibration: 0°/s

Steering Angle Sensor

Steering sensor

Min.: -3276.8°, Max.: 3276.7°

Turning left: Increases

Turning right: Decreases

-

Zero Point of Steering Angle

Memorized zero value

Min.: -3276.8°, Max.: 3276.7°

-

After clearing zero point calibration: 0°

Lateral G

Lateral G

Min.: -25.10 m/s2, Max.: 24.90 m/s2

-

During turning: Changes in proportion with lateral acceleration

Forward and Rearward G

Forward and backward G

Min.: -25.10 m/s2, Max.: 24.90 m/s2

-

During acceleration/deceleration: Changes in proportion with acceleration

Yaw Rate Value

Yaw rate value

Min.: -128°/s, Max.: 127°/s

-

During turning: Changes in proportion with yaw

Steering Angle Value

Steering angle value

Min.: -3276.8°, Max.: 3276.7°

-

During steering operation: Changes in proportion with steering wheel rotation

Slip Indicator Light

Slip indicator light

ON or OFF

ON: Indicator light on

OFF: Indicator light off

-

FR Wheel Speed

Front speed sensor RH

Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)

Vehicle stopped: 0 km/h (0 mph)

When driving at constant speed: No large fluctuations

FL Wheel Speed

Front speed sensor LH

Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)

Vehicle stopped: 0 km/h (0 mph)

When driving at constant speed: No large fluctuations

RR Wheel Speed

Rear speed sensor RH

Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)

Vehicle stopped: 0 km/h (0 mph)

When driving at constant speed: No large fluctuations

RL Wheel Speed

Rear speed sensor LH

Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)

Vehicle stopped: 0 km/h (0 mph)

When driving at constant speed: No large fluctuations

Vehicle Speed

Maximum wheel speed sensor

Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)

Vehicle stopped: 0 km/h (0 mph)

When driving at constant speed: No large fluctuations

FR Wheel Acceleration

Front wheel RH acceleration

Min.: -200.84 m/s2, Max.: 199.27 m/s2

-

During deceleration/acceleration: Changes continuously

FL Wheel Acceleration

Front wheel LH acceleration

Min.: -200.84 m/s2, Max.: 199.27 m/s2

-

During deceleration/acceleration: Changes continuously

RR Wheel Acceleration

Rear wheel RH acceleration

Min.: -200.84 m/s2, Max.: 199.27 m/s2

-

During deceleration/acceleration: Changes continuously

RL Wheel Acceleration

Rear wheel LH acceleration

Min.: -200.84 m/s2, Max.: 199.27 m/s2

-

During deceleration/acceleration: Changes continuously

Stop Light Relay Output

Stop light switch assembly (stop light control relay) output

ON or OFF

ON: Stop light switch assembly (Relay) Output on

OFF: Stop light switch assembly (Relay) Output off

-

EBS Relay

Emergency brake signal operation status

ON or OFF

OFF: Operation off

This item is displayed on the Techstream but is not used

FR Wheel ABS Ctrl Status

Front wheel RH ABS control status

ON or OFF

ON: During control

OFF: Not during control

-

FL Wheel ABS Ctrl Status

Front wheel LH ABS control status

ON or OFF

ON: During control

OFF: Not during control

-

RR Wheel ABS Ctrl Status

Rear wheel RH ABS control status

ON or OFF

ON: During control

OFF: Not during control

-

RL Wheel ABS Ctrl Status

Rear wheel LH ABS control status

ON or OFF

ON: During control

OFF: Not during control

-

RR Wheel EBD Ctrl Status

Rear wheel RH EBD control status

ON or OFF

ON: During control

OFF: Not during control

-

RL Wheel EBD Ctrl Status

Rear wheel LH EBD control status

ON or OFF

ON: During control

OFF: Not during control

-

BA Ctrl Status

BA control status

ON or OFF

ON: During control

OFF: Not during control

-

PBA Ctrl Status

PBA control status

ON or OFF

ON: During control

OFF: Not during control

*

TRC(TRAC) Ctrl Status

TRC (TRAC) control status

ON or OFF

ON: During control

OFF: Not during control

-

TRC(TRAC) Engine Ctrl Status

TRC (TRAC) hybrid control status

ON or OFF

ON: During control

OFF: Not during control

-

TRC(TRAC) Brake Ctrl Status

TRC (TRAC) brake control status

ON or OFF

ON: During control

OFF: Not during control

-

FR Wheel VSC Ctrl Status

Front wheel RH VSC control status

ON or OFF

ON: During control

OFF: Not during control

-

FL Wheel VSC Ctrl Status

Front wheel LH VSC control status

ON or OFF

ON: During control

OFF: Not during control

-

RR Wheel VSC Ctrl Status

Rear wheel RH VSC control status

ON or OFF

ON: During control

OFF: Not during control

-

RL Wheel VSC Ctrl Status

Rear wheel LH VSC control status

ON or OFF

ON: During control

OFF: Not during control

-

Accelerator Opening Angle %

Percentage of accelerator pedal opening angle

Min.: 0.0%, Max.: 127.5%

Accelerator pedal released: 0.0%

During accelerator pedal operation: Changes in proportion with the pedal movement

Regenerative Cooperation

Regenerative cooperation

ON or OFF

ON: Operating

OFF: Not operating

-

FR Regenerative Request

FR regenerative request torque

Min.: 0 Nm, Max.: 1048560 Nm

-

Changes according to brake pedal force

(When depressing the brake pedal lightly after reaching 30 km/h (19 mph) or more, avoiding sudden braking.)

FR Regenerative Operation

FR regenerative operation torque

Min.: 0 Nm, Max.: 1048560 Nm

-

Changes according to brake pedal force

(When depressing the brake pedal lightly after reaching 30 km/h (19 mph) or more, avoiding sudden braking.)

ECB Motor Relay

ABS motor relay

ON or OFF

ON: Relay on

OFF: Relay off

ECB: Electronically Controlled Brake System

ECB Main Relay

ABS main relay

ON or OFF

ON: Relay on

OFF: Relay off

ECB: Electronically Controlled Brake System

ABS Solenoid (SFRH)

Holding solenoid valve (FRH)

ON or OFF

ON: Operating

OFF: Not operating

-

ABS Solenoid (SFRR)

Reduction solenoid valve (FRR)

ON or OFF

ON: Operating

OFF: Not operating

-

ABS Solenoid (SFLH)

Holding solenoid valve (FLH)

ON or OFF

ON: Operating

OFF: Not operating

-

ABS Solenoid (SFLR)

Reduction solenoid valve (FLR)

ON or OFF

ON: Operating

OFF: Not operating

-

ABS Solenoid (SRRH)

Holding solenoid valve (RRH)

ON or OFF

ON: Operating

OFF: Not operating

-

ABS Solenoid (SRRR)

Reduction solenoid valve (RRR)

ON or OFF

ON: Operating

OFF: Not operating

-

ABS Solenoid (SRLH)

Holding solenoid valve (RLH)

ON or OFF

ON: Operating

OFF: Not operating

-

ABS Solenoid (SRLR)

Reduction solenoid valve (RLR)

ON or OFF

ON: Operating

OFF: Not operating

-

ECB Solenoid (SRC)

Regulator cut solenoid valve (SRC)

ON or OFF

ON: Operating

OFF: Not operating

ECB: Electronically Controlled Brake System

ECB Solenoid (SCC)

Switching solenoid valve (SCC)

ON or OFF

ON: Operating

OFF: Not operating

ECB: Electronically Controlled Brake System

ECB Solenoid (SMC)

Master cut solenoid valve (SMC)

ON or OFF

ON: Operating

OFF: Not operating

ECB: Electronically Controlled Brake System

ECB Solenoid (SSC)

Simulator cut solenoid valve (SSC)

ON or OFF

ON: Operating

OFF: Not operating

ECB: Electronically Controlled Brake System

Regulator Pressure Sensor Correction Voltage

Regulator pressure sensor voltage

Min.: -2.50 V, Max.: 2.49 V

-

-

FR Speed Open

Front speed sensor RH open detection

Error or Normal

Error: Momentary interruption detected

Normal: Momentary interruption not detected

  • After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Error" to "Normal".
  • Related DTC: C1464

FL Speed Open

Front speed sensor LH open detection

Error or Normal

Error: Momentary interruption detected

Normal: Momentary interruption not detected

  • After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Error" to "Normal".
  • Related DTC: C1465

RR Speed Open

Rear speed sensor RH open detection

Error or Normal

Normal: Momentary interruption not detected

Normal: Momentary interruption not detected

  • After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Error" to "Normal".
  • Related DTC: C1466

RL Speed Open

Rear speed sensor LH open detection

Error or Normal

Error: Momentary interruption detected

Normal: Momentary interruption not detected

  • After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Error" to "Normal".
  • Related DTC: C1467

Yaw Rate Open

Yaw rate sensor open detection

Error or Normal

Error: Momentary interruption detected

Normal: Momentary interruption not detected

  • After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Error" to "Normal".
  • Related DTC: U0123

Deceleration Open

Acceleration sensor open detection

Error or Normal

Error: Momentary interruption detected

Normal: Momentary interruption not detected

  • After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Error" to "Normal".
  • Related DTC: U0124

Steering Open

Steering sensor open detection

Error or Normal

Error: Momentary interruption detected

Normal: Momentary interruption not detected

  • After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Error" to "Normal".
  • Related DTC: U0126

Master Cylinder Open

Regulator pressure sensor open detection

Error or Normal

Error: Momentary interruption detected

Normal: Momentary interruption not detected

  • After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Error" to "Normal".
  • Related DTC: C1246

Stroke Open

Brake pedal stroke sensor assembly open detection

Error or Normal

Error: Momentary interruption detected

Normal: Momentary interruption not detected

  • After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Error" to "Normal".
  • Related DTC: C1247

FR Wheel Cylinder Open

Wheel cylinder pressure sensor open detection

Error or Normal

Error: Momentary interruption detected

Normal: Momentary interruption not detected

  • After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Error" to "Normal".
  • Related DTC: C1364

Accumulator Open

Accumulator pressure sensor open detection

Error or Normal

Error: Momentary interruption detected

Normal: Momentary interruption not detected

  • After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Error" to "Normal".
  • Related DTC: C1365

HV Communication Open

Hybrid vehicle communication open detection

Error or Normal

Error: Hybrid vehicle control ECU assembly communication invalid state detected

Normal: Hybrid vehicle control ECU assembly communication invalid state not detected

  • After hybrid vehicle control ECU assembly communication invalid state occurs, if there no further invalid state occurs, it switches from "Error" to "Normal".
  • Related DTC: U0293

BS1 Voltage Value

BS voltage value

Min.: 0.00 V, Max.: 20.00 V

-

Changes in proportion to auxiliary battery voltage

BH Standby Light

Brake hold standby indicator light

ON or OFF

ON: Indicator light on

OFF: Indicator light off

-

BH Operated Light

Brake hold operated indicator light

ON or OFF

ON: Indicator light on

OFF: Indicator light off

-

TRAC/VSC Off Mode

TRC (TRAC)/VSC off mode

Normal, TRC OFF or VSC OFF

Normal: Normal mode

TRC OFF: TRC (TRAC) off mode

VSC OFF: VSC off mode

-

Number of DTC

Number of DTC

Min.: 0, Max.: 255

-

Number of DTCs output is displayed

Wheel Cylinder Pressure Sensor

Wheel cylinder pressure sensor

Min.: 0.00 V, Max.: 5.00 V

Brake pedal released: 0.10 to 0.90 V

Reading increases when brake pedal is depressed

Regulator Pressure Sensor Output After Filter

Regulator pressure sensor output after filter

Min.: -1.00 Mpa, Max.: 23.99 Mpa

-

-

Regulator Pressure Sensor Variation

Regulator pressure sensor variation

Min.: -30 Mpa/s, Max.: 225 Mpa/s

-

-

SLA Solenoid Current

Linear solenoid additional valve (SLA) current

Min.: 0.00 A, Max.: 3.00 A

Brake pedal released: 0.00 A

-

SLR Solenoid Current

Linear solenoid reduction valve (SLR) current

Min.: 0.00 A, Max.: 3.00 A

Brake pedal released: 0.00 A

-

SSC Solenoid Current

Simulator cut solenoid valve (SSC) current

Min.: 0.00 A, Max.: 3.00 A

Brake pedal released: 0.00 A

-

SCC Solenoid Current

Switching solenoid valve (SCC) current

Min.: 0.00 A, Max.: 3.00 A

Brake pedal released: 0.00 A

-

SMC Solenoid Current

Master cut solenoid valve (SMC) current

Min.: 0.00 A, Max.: 3.00 A

Brake pedal released: 0.00 A

-

SRC Solenoid Current

Regulator cut solenoid valve (SRC) current

Min.: 0.00 A, Max.: 3.00 A

Brake pedal released: 0.00 A

-

Air Bag ECU Communication Open

Airbag ECU assembly communication open detection

Error or Normal

Error: Momentary interruption detected

Normal: Momentary interruption not detected

  • After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Error" to "Normal".
  • Related DTC: U0151
  • *: w/ Pre-collision System

ACTIVE TEST

HINT:

Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

(a) Warm up the engine.

(b) Turn the power switch off.

(c) Connect the Techstream to the DLC3.

(d) Turn the power switch on (IG).

(e) Turn the Techstream on.

(f) Enter the following menus: Chassis / ABS/VSC/TRAC / Active Test.

(g) According to the display on the Techstream, perform the Active Test.

Chassis > ABS/VSC/TRAC > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

ABS Warning Light

ABS warning light

Warning light ON/OFF

Observe combination meter assembly

Brake Warning Light

Brake warning light / red (malfunction)

Warning light ON/OFF

Observe combination meter assembly

ECB Warning Light

Brake warning light / yellow (minor malfunction)

Warning light ON/OFF

  • Observe combination meter assembly
  • ECB: Electronically Controlled Brake System

Buzzer

Meter buzzer

Buzzer ON/OFF

Buzzer can be heard

Stop Light Relay

Stop light switch assembly (stop light control relay)

Stop light switch assembly (Relay) ON/OFF

Stop lights come on

ECB Main Relay

ABS main relay

Relay ON/OFF

ECB: Electronically Controlled Brake System

ECB Motor Relay

ABS motor relay

Relay ON/OFF

ECB: Electronically Controlled Brake System

ABS Solenoid (SRLR)

Reduction solenoid valve (RLR)

Solenoid ON/OFF

-

ABS Solenoid (SRLH)

Holding solenoid valve (RLH)

Solenoid ON/OFF

-

ABS Solenoid (SRRR)

Reduction solenoid valve (RRR)

Solenoid ON/OFF

-

ABS Solenoid (SRRH)

Holding solenoid valve (RRH)

Solenoid ON/OFF

-

ABS Solenoid (SFLR)

Reduction solenoid valve (FLR)

Solenoid ON/OFF

-

ABS Solenoid (SFLH)

Holding solenoid valve (FLH)

Solenoid ON/OFF

-

ABS Solenoid (SFRR)

Reduction solenoid valve (FRR)

Solenoid ON/OFF

-

ABS Solenoid (SFRH)

Holding solenoid valve (FRH)

Solenoid ON/OFF

-

ECB Control Invalid

Electronically controlled brake system control invalid

Control invalid ON/OFF

  • Electronically controlled brake system control is disabled (braking with no accumulator assist)
  • ECB: Electronically Controlled Brake System

Accumulator Zero Down

Reduction of pressure in accumulator

Activation ON/OFF

Brake fluid in the accumulator makes noise

Actuator Air Bleeding Pattern

Actuator air bleeding pattern activation

Activation ON/OFF

When accumulator pressure drops, pump operation creates sound

Power Supply Air Bleeding Pattern1

Power supply air bleeding pattern activation 1

Activation ON/OFF

When accumulator pressure drops, pump operation creates sound

Power Supply Air Bleeding Pattern2

Power supply air bleeding pattern activation 2

Activation ON/OFF

When accumulator pressure drops, pump operation creates sound

BH Standby Light

Brake hold standby indicator light

Indicator light ON/OFF

Observe combination meter assembly

BH Operated Light

Brake hold operated indicator light

Indicator light ON/OFF

Observe combination meter assembly

TRC(TRAC) OFF Indicator Light

Multi-information display (TRC (TRAC) OFF message)

Display ON/OFF

Observe combination meter assembly

VSC OFF Indicator Light

VSC OFF indicator light

Indicator light ON/OFF

Observe combination meter assembly

Slip Indicator Light

Slip indicator light

Indicator light ON/OFF

Observe combination meter assembly

EBS Relay

Emergency brake signal operation

Emergency brake signal operation ON/OFF

This item is displayed on the Techstream but is not used

ECB Solenoid (SLR)

Linear solenoid reduction valve (SLR)

Valve close ON/OFF

ECB: Electronically Controlled Brake System

ECB Solenoid (SLA)

Linear solenoid additional valve (SLA)

Valve close ON/OFF

ECB: Electronically Controlled Brake System

Stroke Simulator Cut Valve Pattern

Simulator cut solenoid valve (SSC)

Pattern activation ON/OFF

Difficult to identify visually

ECB Solenoid (SRC)

Regulator cut solenoid valve (SRC)

Solenoid ON/OFF

  • Operation sound of solenoid (clicking sound) can be heard
  • ECB: Electronically Controlled Brake System

ECB Solenoid (SMC)

Master cut solenoid valve (SMC)

Solenoid ON/OFF

  • Operation sound of solenoid (clicking sound) can be heard
  • ECB: Electronically Controlled Brake System

ECB Solenoid (SCC)

Switching solenoid valve (SCC)

Solenoid ON/OFF

  • Operation sound of solenoid (clicking sound) can be heard
  • ECB: Electronically Controlled Brake System

ECB Solenoid (SSC)

Simulator cut solenoid valve (SSC)

Solenoid ON/OFF

  • Operation sound of solenoid (clicking sound) can be heard
  • ECB: Electronically Controlled Brake System

ECB Solenoid (SMC/SRC/SCC)

Switching solenoid valve (SMC/SRC/SCC)

Solenoid ON/OFF

  • Operation sound of solenoid (clicking sound) can be heard
  • ECB: Electronically Controlled Brake System

ABS Solenoid

Solenoid valve (FRH, FRR, FLH, FLR, RRH, RRR, RLH or RLR)

Solenoid SFRH/SFRR/SFLH/SFLR/SRRH/SRRR/SRLH/SRLR

Operation sound of solenoid (clicking sound) can be heard