Last Modified: 01-30-2024 6.11:8.1.0 Doc ID: RM100000001EADC
Model Year Start: 2019 Model: RAV4 Prod Date Range: [11/2018 - 02/2019]
Title: BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster): C1380; Stop Light Control Relay Malfunction; 2019 MY RAV4 RAV4 HV [11/2018 - 02/2019]

DTC

C1380

Stop Light Control Relay Malfunction

DESCRIPTION

When any of the following conditions are met, the skid control ECU (brake booster with master cylinder assembly) sets the drive output (STPO) ON which operates the stop light control relay (stop light switch assembly) and turns on the stop lights.

Illumination Conditions:

  • Pre-collision brake is operating.*
  • The dynamic radar cruise control system is operating and is applying the brakes.*
  • Secondary collision brake is operating.
  • Brake hold is operating.
  • *: w/ Pre-collision System

DTC No.

Detection Item

INF Code

DTC Detection Condition

Trouble Area

Note

C1380

Stop Light Control Relay Malfunction

761

762

  • INF Code: 761
    • When the voltage at terminal IG1 is 9.5 V higher than, stop light drive output (STPO) is ON and STP is OFF for 2 seconds or more.
  • INF Code: 762
    • When the voltage at terminal IG1 is 9.5 V higher than, stop light drive output (STPO) is OFF and the input signals for STP and STP2 differ for 5 seconds or more.
  • Stop light switch assembly circuit
  • Stop light switch assembly
  • Skid control ECU (Brake booster with master cylinder assembly)
  • Hybrid vehicle control ECU assembly
  • Certification ECU (smart key ECU assembly)
  • Rear combination light socket and wire LH
  • Stop light LED
  • Rear combination light socket and wire RH
  • Center stop light cord assembly
  • Center stop light assembly
  • Open or short in wire harness

-

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

  • When replacing the skid control ECU (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve.

    Click here

    Click here 2019 MY RAV4 RAV4 HV [11/2018 - 02/2019]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster): UTILITY

  • Inspect the fuses for circuits related to this system before performing the following procedure.
  • If the certification ECU (smart key ECU assembly) is replaced, refer to Registration.

    Click here 2019 MY RAV4 HV [11/2018 - 10/2019]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, HV Model): REGISTRATION

HINT:

When C1249 is output together with C1380, inspect and repair the trouble areas indicated by C1249 first.

Click here 2019 MY RAV4 RAV4 HV [11/2018 - 02/2019]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster): C1249; Open Circuit in Stop Light Switch Circuit

PROCEDURE

1.

CHECK HARNESS AND CONNECTOR (STP, STPO AND STP2 TERMINAL)

(a) Turn the power switch off.

*a

Front view of wire harness connector

(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))

(b) Make sure that there is no looseness at the locking part and the connecting part of the connector.

(c) Disconnect the A42 skid control ECU (brake booster with master cylinder assembly) connector.

(d) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

A42-33 (STP) - Body ground

Stop light switch assembly on (Brake pedal depressed)

11 to 14 V

A42-33 (STP) - Body ground

Stop light switch assembly off (Brake pedal released)

Below 1.5 V

A42-3 (STPO) - Body ground

Always

11 to 14 V

A42-6 (STP2) - Body ground

Stop light switch assembly on (Brake pedal depressed)

11 to 14 V

A42-6 (STP2) - Body ground

Stop light switch assembly off (Brake pedal released)

Below 1.5 V

Result

Proceed to

All terminal voltages are normal.

A

Only STP2 terminal voltage abnormal.

B

Only STPO terminal voltage abnormal.

C

Only STP terminal voltage abnormal.

D

STPO terminal and STP terminal voltage abnormal.

E

B

GO TO STEP 5

C

GO TO STEP 9

D

GO TO STEP 10

E

GO TO STEP 14

A

2.

PERFORM ACTIVE TEST USING TECHSTREAM (STOP LIGHT RELAY)

(a) Reconnect the A42 skid control ECU (brake booster with master cylinder assembly) connector.

(b) Select the Active Test on the Techstream.

Click here 2019 MY RAV4 RAV4 HV [11/2018 - 02/2019]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster): DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRAC > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

Stop Light Relay

Stop light switch assembly (stop light control relay)

Stop light switch assembly (Relay) ON/OFF

Stop lights come on

Chassis > ABS/VSC/TRAC > Active Test

Tester Display

Stop Light Relay

(c) According to the display on the Techstream, perform the Active Test and check the operation of the stop lights.

OK:

Stop lights turn on/off in accordance with the Active Test.

NG

GO TO STEP 4

OK

3.

RECONFIRM DTC

(a) Clear the DTCs.

Click here 2019 MY RAV4 RAV4 HV [11/2018 - 02/2019]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster): DTC CHECK / CLEAR

Chassis > ABS/VSC/TRAC > Clear DTCs

(b) Select the Active Test on the Techstream.

Click here 2019 MY RAV4 RAV4 HV [11/2018 - 02/2019]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster): DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRAC > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

Stop Light Relay

Stop light switch assembly (stop light control relay)

Stop light switch assembly (Relay) ON/OFF

Stop lights come on

Chassis > ABS/VSC/TRAC > Active Test

Tester Display

Stop Light Relay

(c) According to the display on the Techstream, perform the Active Test.

(d) Check if the same DTC is output.

Click here 2019 MY RAV4 RAV4 HV [11/2018 - 02/2019]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster): DTC CHECK / CLEAR

Chassis > ABS/VSC/TRAC > Trouble Codes

Result

Proceed to

DTC C1380 is output.

A

DTC C1380 is not output.

B

A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

B

USE SIMULATION METHOD TO CHECK

4.

INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

(a) Select the Active Test on the Techstream.

Click here 2019 MY RAV4 RAV4 HV [11/2018 - 02/2019]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster): DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRAC > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

Stop Light Relay

Stop light switch assembly (stop light control relay)

Stop light switch assembly (Relay) ON/OFF

Stop lights come on

Chassis > ABS/VSC/TRAC > Active Test

Tester Display

Stop Light Relay

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

A40-4 (ACC) - Body ground

Active Test is on

1.5 V or less

*a

Component with harness connected

(Stop Light Switch Assembly)

OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

5.

CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - HYBRID VEHICLE CONTROL ECU ASSEMBLY)

(a) Disconnect the A29 hybrid vehicle control ECU assembly connector.

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

A42-6 (STP2) - Body ground

Stop light switch assembly on (Brake pedal depressed)

11 to 14 V

A42-6 (STP2) - Body ground

Stop light switch assembly off (Brake pedal released)

Below 1.5 V

*a

Front view of wire harness connector

(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))

OK

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

NG

6.

CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - SMART KEY ECU ASSEMBLY)

(a) Disconnect the M7 certification ECU (smart key ECU assembly) connector.

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

A42-6 (STP2) - Body ground

Stop light switch assembly on (Brake pedal depressed)

11 to 14 V

A42-6 (STP2) - Body ground

Stop light switch assembly off (Brake pedal released)

Below 1.5 V

*a

Front view of wire harness connector

(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))

OK

REPLACE SMART KEY ECU ASSEMBLY

NG

7.

CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)

(a) Disconnect the A40 stop light switch assembly connector.

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

A42-6 (STP2) - Body ground

Always

Below 1.5 V

*a

Front view of wire harness connector

(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

8.

CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

A42-6 (STP2) - A40-3 (L)

Always

Below 1 Ω

A42-6 (STP2) or A40-3 (L) - Body ground

Always

10 kΩ or higher

OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.

CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)

(a) Disconnect the A40 stop light switch assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

A42-3 (STPO) - A40-4 (ACC)

Always

Below 1 Ω

OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.

CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - STOP LIGHT LED)

(a) Disconnect the A stop light LED connector.

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

A42-33 (STP) - Body ground

Stop light switch assembly on (Brake pedal depressed)

11 to 14 V

A42-33 (STP) - Body ground

Stop light switch assembly off (Brake pedal released)

1.5 V or less

*a

Front view of wire harness connector

(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))

OK

REPLACE STOP LIGHT LED

NG

11.

CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - REAR COMBINATION LIGHT SOCKET AND WIRE LH)

(a) Disconnect the N18 rear combination light socket and wire LH connector.

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

A42-33 (STP) - Body ground

Stop light switch assembly on (Brake pedal depressed)

11 to 14 V

A42-33 (STP) - Body ground

Stop light switch assembly off (Brake pedal released)

1.5 V or less

*a

Front view of wire harness connector

(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))

OK

REPLACE REAR COMBINATION LIGHT SOCKET AND WIRE LH

NG

12.

CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - STOP LIGHT LED)

(a) Disconnect the B stop light LED connector.

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

A42-33 (STP) - Body ground

Stop light switch assembly on (Brake pedal depressed)

11 to 14 V

A42-33 (STP) - Body ground

Stop light switch assembly off (Brake pedal released)

1.5 V or less

*a

Front view of wire harness connector

(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))

OK

REPLACE STOP LIGHT LED

NG

13.

CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - REAR COMBINATION LIGHT SOCKET AND WIRE RH)

(a) Disconnect the M14 rear combination light socket and wire RH connector.

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

A42-33 (STP) - Body ground

Stop light switch assembly on (Brake pedal depressed)

11 to 14 V

A42-33 (STP) - Body ground

Stop light switch assembly off (Brake pedal released)

1.5 V or less

*a

Front view of wire harness connector

(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))

OK

REPLACE REAR COMBINATION LIGHT SOCKET AND WIRE RH

NG

GO TO STEP 16

14.

CHECK STOP LIGHT SWITCH ASSEMBLY POWER SOURCE CIRCUIT

(a) Disconnect the A40 stop light switch assembly connector.

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

A40-7 (B) - Body ground

Always

11 to 14 V

*a

Front view of wire harness connector

(to Stop Light Switch Assembly)

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

A40-2 (GND) - Body ground

Always

Below 1 Ω

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

15.

CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

A42-3 (STPO) or A40-4 (ACC) - Body ground

Always

10 kΩ or higher

OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.

CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - CENTER STOP LIGHT ASSEMBLY)

(a) Disconnect the C center stop light assembly connector.

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

A42-33 (STP) - Body ground

Stop light switch assembly on (Brake pedal depressed)

11 to 14 V

A42-33 (STP) - Body ground

Stop light switch assembly off (Brake pedal released)

1.5 V or less

*a

Front view of wire harness connector

(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))

OK

REPLACE CENTER STOP LIGHT ASSEMBLY

NG

17.

CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - CENTER STOP LIGHT CORD ASSEMBLY)

(a) Disconnect the R1 center stop light cord assembly connector.

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

A42-33 (STP) - Body ground

Stop light switch assembly on (Brake pedal depressed)

11 to 14 V

A42-33 (STP) - Body ground

Stop light switch assembly off (Brake pedal released)

1.5 V or less

*a

Front view of wire harness connector

(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))

OK

REPLACE CENTER STOP LIGHT CORD ASSEMBLY

NG

18.

CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)

(a) Disconnect the A40 stop light switch assembly connector.

*a

Front view of wire harness connector

(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

A42-33 (STP) - Body ground

Always

1.5 V or less

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

19.

CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

A40-1 (OUT) - A42-33 (STP)

Always

Below 1 Ω

A40-1 (OUT) or A42-33 (STP) - Body ground

Always

10 kΩ or higher

OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR