Last Modified: 01-30-2024 6.11:8.1.0 Doc ID: RM100000001EAD8
Model Year Start: 2019 Model: RAV4 Prod Date Range: [11/2018 - 02/2019]
Title: BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster): C1273,C1274,C1466,C1467; Low Output Signal of Rear Speed Sensor RH (Test Mode DTC); 2019 MY RAV4 RAV4 HV [11/2018 - 02/2019]

DTC

C1273

Low Output Signal of Rear Speed Sensor RH (Test Mode DTC)

DTC

C1274

Low Output Signal of Rear Speed Sensor LH (Test Mode DTC)

DTC

C1466

Rear Speed Sensor RH Circuit

DTC

C1467

Rear Speed Sensor LH Circuit

DESCRIPTION

Each speed sensor detects the wheel speed and sends the signals to the skid control ECU (brake booster with master cylinder assembly). These signals are used for ABS control.

DTCs C1273 and C1274 are cleared when the speed sensor sends a wheel speed signal or when Test Mode ends. DTCs C1273 and C1274 are output only in Test Mode.

DTC No.

Detection Item

INF Code

DTC Detection Condition

Trouble Area

Note

C1273

Low Output Signal of Rear Speed Sensor RH (Test Mode DTC)

-

Detected only during Test Mode.

  • Rear speed sensor RH (Rear axle hub and bearing assembly RH)
  • Sensor installation
  • Rear speed sensor rotor RH (Rear axle hub and bearing assembly RH)
  • Skid control sensor wire RH (No. 1 parking brake wire assembly)

-

C1274

Low Output Signal of Rear Speed Sensor LH (Test Mode DTC)

-

Detected only during Test Mode.

  • Rear speed sensor LH (Rear axle hub and bearing assembly LH)
  • Sensor installation
  • Rear speed sensor rotor LH (Rear axle hub and bearing assembly LH)
  • Skid control sensor wire LH (No. 2 parking brake wire assembly)

-

C1466

Rear Speed Sensor RH Circuit

521

522

523

524

526

527

528

529

  • INF Code: 521
    • At a vehicle speed of 10 km/h (6 mph) or more, speed sensor output from one or two wheels is lower than that from other wheels for 15 seconds or more.
  • INF Code: 522
    • At a vehicle speed of 10 km/h (6 mph) or more, outputs from both front speed sensors are 0 km/h (0 mph) for 15 seconds or more.
  • INF Code: 523
    • An open is detected in the speed sensor signal circuit for 0.5 seconds or more.
  • INF Code: 524
    • Instantaneous interruption of sensor signal from the malfunctioning wheel occurs 255 times or more.
  • INF Code: 526
    • When VM1 voltage is 8.6 V or more, sensor supply voltage drops for 0.5 seconds or more.
  • INF Code: 527
    • At a vehicle speed of 10 km/h (6 mph) or more, speed sensor output from one wheel is 0 km/h (0 mph) for 1 second or more.
  • INF Code: 528
    • When VM1 voltage is 8.6 V or more, sensor supply voltage drops for 60 seconds or more.
  • INF Code: 529
    • Speed sensor output is 270 km/h (167 mph) or more continuously for 5 seconds or more.
  • INF Code: 521, 522, 524, 527
    • Open or short in speed sensor
    • Improperly installed speed sensor, or abnormal clearance between sensor and rotor
    • Open or short in wire harness
    • Improperly connected connector, deformation or corrosion of terminals
    • Rear speed sensor RH (Rear axle hub and bearing assembly RH)
    • Skid control ECU (Brake booster with master cylinder assembly)
  • INF Code: 523
    • Open or short in speed sensor
    • Open or short in wire harness
    • Improperly connected connector, deformation or corrosion of terminals
    • Rear speed sensor RH (Rear axle hub and bearing assembly RH)
    • Skid control ECU (Brake booster with master cylinder assembly)
  • INF Code: 526, 528
    • Open or short in wire harness
    • Skid control ECU (Brake booster with master cylinder assembly)
  • INF Code: 529
    • Open or short in speed sensor
    • Open or short in wire harness
    • Rear speed sensor RH (Rear axle hub and bearing assembly RH)
    • Skid control ECU (Brake booster with master cylinder assembly)

-

C1467

Rear Speed Sensor LH Circuit

531

532

533

534

536

537

538

539

  • INF Code: 531
    • At a vehicle speed of 10 km/h (6 mph) or more, speed sensor output from one or two wheels is lower than that from other wheels for 15 seconds or more.
  • INF Code: 532
    • At a vehicle speed of 10 km/h (6 mph) or more, outputs from both front speed sensors are 0 km/h (0 mph) for 15 seconds or more.
  • INF Code: 533
    • An open is detected in the speed sensor signal circuit for 0.5 seconds or more.
  • INF Code: 534
    • Instantaneous interruption of sensor signal from the malfunctioning wheel occurs 255 times or more.
  • INF Code: 536
    • When VM1 voltage is 8.6 V or more, sensor supply voltage drops for 0.5 seconds or more.
  • INF Code: 537
    • At a vehicle speed of 10 km/h (6 mph) or more, speed sensor output from one wheel is 0 km/h (0 mph) for 1 second or more.
  • INF Code: 538
    • When VM1 voltage is 8.6 V or more, sensor supply voltage drops for 60 seconds or more.
  • INF Code: 539
    • Speed sensor output is 270 km/h (167 mph) or more continuously for 5 seconds or more.
  • INF Code: 531, 532, 534, 537
    • Open or short in speed sensor
    • Improperly installed speed sensor, or abnormal clearance between sensor and rotor
    • Open or short in wire harness
    • Improperly connected connector, deformation or corrosion of terminals
    • Rear speed sensor LH (Rear axle hub and bearing assembly LH)
    • Skid control ECU (Brake booster with master cylinder assembly)
  • INF Code: 533
    • Open or short in speed sensor
    • Open or short in wire harness
    • Improperly connected connector, deformation or corrosion of terminals
    • Rear speed sensor LH (Rear axle hub and bearing assembly LH)
    • Skid control ECU (Brake booster with master cylinder assembly)
  • INF Code: 536, 538
    • Open or short in wire harness
    • Skid control ECU (Brake booster with master cylinder assembly)
  • INF Code: 539
    • Open or short in speed sensor
    • Open or short in wire harness
    • Rear speed sensor LH (Rear axle hub and bearing assembly LH)
    • Skid control ECU (Brake booster with master cylinder assembly)

-

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve.

Click here 2019 MY RAV4 RAV4 HV [11/2018 - 02/2019]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster): UTILITY

PROCEDURE

1.

CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)

(a) Using the Techstream, check for any momentary interruptions in the wire harness and connector corresponding to a DTC.

Click here 2019 MY RAV4 RAV4 HV [11/2018 - 02/2019]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster): CHECK FOR INTERMITTENT PROBLEMS

Chassis > ABS/VSC/TRAC > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

RR Speed Open

Rear speed sensor RH open detection

Error or Normal

Normal: Momentary interruption not detected

Normal: Momentary interruption not detected

After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Error" to "Normal".

RL Speed Open

Rear speed sensor LH open detection

Error or Normal

Error: Momentary interruption detected

Normal: Momentary interruption not detected

After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Error" to "Normal".

Chassis > ABS/VSC/TRAC > Data List

Tester Display

RR Speed Open

RL Speed Open

OK:

Normal (There are no momentary interruptions.)

HINT:

Perform the above inspection before removing the sensor and connector.

NG

GO TO STEP 5

OK

2.

READ VALUE USING TECHSTREAM (REAR SPEED SENSOR)

(a) Select the Data List on the Techstream.

Click here 2019 MY RAV4 RAV4 HV [11/2018 - 02/2019]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster): DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRAC > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

RR Wheel Speed

Rear speed sensor RH

Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)

Vehicle stopped: 0 km/h (0 mph)

When driving at constant speed: No large fluctuations

RL Wheel Speed

Rear speed sensor LH

Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)

Vehicle stopped: 0 km/h (0 mph)

When driving at constant speed: No large fluctuations

Chassis > ABS/VSC/TRAC > Data List

Tester Display

RR Wheel Speed

RL Wheel Speed

(b) Check the speed value output from the speed sensor displayed on the Techstream.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.

Click here 2019 - 2021 MY RAV4 RAV4 HV [11/2018 - 12/2021]; METER / GAUGE / DISPLAY: METER / GAUGE SYSTEM: OPERATION CHECK

OK:

The speed value output from the speed sensor displayed on the Techstream is similar to the speed indicated on the speedometer.

NG

GO TO STEP 5

OK

3.

PERFORM TEST MODE INSPECTION (SIGNAL CHECK)

(a) Turn the power switch off.

(b) Perform the sensor check in Test Mode Procedure.

Click here 2019 MY RAV4 RAV4 HV [11/2018 - 02/2019]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster): TEST MODE PROCEDURE

Chassis > ABS/VSC/TRAC > Utility

Tester Display

Signal Check

OK:

All Test Mode DTCs are cleared.

NG

GO TO STEP 5

OK

4.

RECONFIRM DTC

(a) Turn the power switch off.

(b) Clear the DTCs.

Click here 2019 MY RAV4 RAV4 HV [11/2018 - 02/2019]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster): DTC CHECK / CLEAR

Chassis > ABS/VSC/TRAC > Clear DTCs

(c) Turn the power switch on (READY).

(d) Perform a road test.

(e) Check if the same DTC is output.

Click here 2019 MY RAV4 RAV4 HV [11/2018 - 02/2019]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster): DTC CHECK / CLEAR

Chassis > ABS/VSC/TRAC > Trouble Codes

Result

Proceed to

DTCs C1466 and C1467 are not output.

A

DTCs C1466 and/or C1467 are output.

B

HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step.

Click here 2019 - 2021 MY RAV4 RAV4 HV [11/2018 - 12/2021]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster): PROBLEM SYMPTOMS TABLE

A

USE SIMULATION METHOD TO CHECK

B

GO TO STEP 6

5.

CHECK REAR SPEED SENSOR INSTALLATION

(a) Turn the power switch off.

*a

No clearance

*b

OK

*c

NG

(b) Check the speed sensor installation.

OK:

There is no clearance between the sensor and rear axle hub.

NG

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY

OK

6.

INSPECT PARKING BRAKE WIRE ASSEMBLY

(a) Make sure that there is no looseness at the locking part and the connecting part of the connectors.

*A

for RH

*B

for LH

*1

Skid Control Sensor Wire (Parking Brake Wire Assembly)

*a

Front view of wire harness connector

(to Sensor Side Connector)

*b

Front view of wire harness connector

(to Vehicle Side Connector)

(b) Disconnect the M50 or N58 skid control sensor wire (parking brake wire assembly) connector.

(c) Disconnect the MM2 or NN2 skid control sensor wire (parking brake wire assembly) connector.

(d) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

for RH

Tester Connection

Condition

Specified Condition

M50-2 (RA+) - MM2-3

Always

Below 1 Ω

M50-2 (RA+) or MM2-3 - Body ground and other terminals

Always

10 kΩ or higher

M50-1 (RA-) - MM2-4

Always

Below 1 Ω

M50-1 (RA-) or MM2-4 - Body ground and other terminals

Always

10 kΩ or higher

for LH

Tester Connection

Condition

Specified Condition

N58-2 (LA+) - NN2-3

Always

Below 1 Ω

N58-2 (LA+) or NN2-3 - Body ground and other terminals

Always

10 kΩ or higher

N58-1 (LA-) - NN2-4

Always

Below 1 Ω

N58-1 (LA-) or NN2-4 - Body ground and other terminals

Always

10 kΩ or higher

NOTICE:

Check the speed sensor signal after replacement.

Click here 2019 MY RAV4 RAV4 HV [11/2018 - 02/2019]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster): TEST MODE PROCEDURE

NG

REPLACE PARKING BRAKE WIRE ASSEMBLY

OK

7.

CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - REAR SPEED SENSOR)

(a) Make sure that there is no looseness at the locking part and the connecting part of the connector.

(b) Reconnect the MM2 or NN2 skid control sensor wire (parking brake wire assembly) connector.

(c) Disconnect the A42 skid control ECU (brake booster with master cylinder assembly) connector.

(d) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

for RH

Tester Connection

Condition

Specified Condition

A42-22 (RR+) - M50-2 (RA+)

Always

Below 1 Ω

A42-22 (RR+) or M50-2 (RA+) - Body ground

Always

10 kΩ or higher

A42-9 (RR-) - M50-1 (RA-)

Always

Below 1 Ω

A42-9 (RR-) or M50-1 (RA-) - Body ground

Always

10 kΩ or higher

for LH

Tester Connection

Condition

Specified Condition

A42-20 (RL+) - N58-2 (LA+)

Always

Below 1 Ω

A42-20 (RL+) or N58-2 (LA+) - Body ground

Always

10 kΩ or higher

A42-7 (RL-) - N58-1 (LA-)

Always

Below 1 Ω

A42-7 (RL-) or N58-1 (LA-) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

8.

INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR OUTPUT)

(a) Reconnect the A42 skid control ECU (brake booster with master cylinder assembly) connector.

*A

for RH

*B

for LH

*a

Front view of wire harness connector

(to Rear Speed Sensor (Rear Axle Hub and Bearing Assembly))

(b) Turn the power switch on (IG).

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

for RH

Tester Connection

Condition

Specified Condition

M50-2 (RA+) - Body ground

Power switch on (IG)

5.7 to 14 V

for LH

Tester Connection

Condition

Specified Condition

N58-2 (LA+) - Body ground

Power switch on (IG)

5.7 to 14 V

OK

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY

NG

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY