| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM100000001EAD4 |
| Model Year Start: 2019 | Model: RAV4 | Prod Date Range: [11/2018 - 02/2019] |
| Title: BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster): Brake Hold Standby Indicator Light Circuit; 2019 MY RAV4 RAV4 HV [11/2018 - 02/2019] | ||
|
Brake Hold Standby Indicator Light Circuit |
DESCRIPTION
The brake hold standby indicator light turns on if brake hold control is possible when the following conditions required for operation standby are met and the brake hold switch (integration control and panel assembly) is turned on while the power switch is on (IG).
-
Conditions required for operation standby:
- The driver's door is closed.
- Driver's seat belt is fastened.
- The system is normal.
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
When replacing the skid control ECU (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve.
Click here
![2019 MY RAV4 RAV4 HV [11/2018 - 02/2019]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster): UTILITY](/t3Portal/stylegraphics/info.gif)
PROCEDURE
|
1. |
PRE-CHECK |
(a) If the brake hold standby indicator light does not illuminate even though the brake hold switch (integration control and panel assembly) is pushed, check that the brake hold function operation conditions are met.
- The driver's door is closed.
- Driver's seat belt is fastened.
- The system is normal.
HINT:
If a malfunction occurs in one of the following systems, the brake hold operated indicator light will blink. If this occurs, perform troubleshooting on the malfunctioning system.
- Brake system
- Electric parking brake system
- Hybrid control system
|
|
2. |
PERFORM ACTIVE TEST USING TECHSTREAM (BRAKE HOLD STANDBY INDICATOR LIGHT) |
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Select the Active Test on the Techstream.
Click here
Chassis > ABS/VSC/TRAC > Active Test
|
Tester Display |
Measurement Item |
Control Range |
Diagnostic Note |
|---|---|---|---|
|
BH Standby Light |
Brake hold standby indicator light |
Indicator light ON/OFF |
Observe combination meter |
(d) Select the Data List on the Techstream.
Click here
Chassis > ABS/VSC/TRAC > Data List
|
Tester Display |
Measurement Item |
Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
BH Standby Light |
Brake hold standby indicator light |
ON or OFF |
ON: Indicator light on OFF: Indicator light off |
- |
Chassis > ABS/VSC/TRAC > Active Test
|
Active Test Display |
|---|
|
BH Standby Light |
|
Data List Display |
|---|
|
BH Standby Light |
(e) Check the operating condition of the brake hold standby indicator light when operating it using the Techstream.
|
Result |
Proceed to |
|---|---|
|
Brake hold standby indicator light in the Data List does not change using the Active Test. |
A |
|
Brake hold standby indicator light in the Data List turns ON/OFF using the Active Test. |
B |
| A |
|
|
|
3. |
INSPECT COMBINATION METER ASSEMBLY |
(a) Turn the power switch off.
(b) Perform the Active Test of the combination meter assembly (meter CPU) using the Techstream.
Click here
Body Electrical > Combination Meter > Active Test
|
Tester Display |
|---|
|
Brake Hold Indicator |
(c) Check the combination meter assembly.
OK:
The brake hold standby indicator light turns on or off in accordance with the Techstream operation.
| NG |
|
|
|
4. |
INSPECT INTEGRATION CONTROL AND PANEL ASSEMBLY |
(a) Turn the power switch off.
(b) Remove the brake hold switch (integration control and panel assembly).
Click here
(c) Inspect the brake hold switch (integration control and panel assembly).
Click here
OK:
The brake hold switch (integration control and panel assembly) operates normally.
| NG |
|
|
|
5. |
CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - INTEGRATION CONTROL AND PANEL ASSEMBLY) |
(a) Disconnect the A42 skid control ECU (brake booster with master cylinder assembly) connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
A42-10 (HZRI) - G32-24 (+B) |
Always |
Below 1 Ω |
|
A42-10 (HZRI) or G32-24 (+B) - Body ground |
Always |
10 kΩ or higher |
|
G32-15 (E) - Body ground |
Always |
Below 1 Ω |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
6. |
INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY |
(a) Turn on the interior lights and check that they illuminate, and then set the switch so that the lights illuminate when the door is opened.
(b) Check that the lights illuminate when the driver door is opened.
OK:
The interior lights illuminate when the driver door is opened.
| NG |
|
INSPECT LIGHTING SYSTEM w/ Headlight ECU: Click here
w/o Headlight ECU: Click here
|
|
|
7. |
CHECK HARNESS AND CONNECTOR (CTY TERMINAL) |
|
(a) Measure the voltage according to the value(s) in the table below. Standard Voltage:
|
|
| OK |
|
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR (CTY CIRCUIT) |
|
|