Last Modified: 01-30-2024 6.11:8.1.0 Doc ID: RM100000001E7JJ
Model Year Start: 2019 Model: RAV4 Prod Date Range: [11/2018 - 08/2020]
Title: NAVIGATION / MULTI INFO DISPLAY: NAVIGATION SYSTEM: Vehicle Speed Signal Circuit between Navigation ECU and Combination Meter; 2019 - 2020 MY RAV4 RAV4 HV [11/2018 - 08/2020]

Vehicle Speed Signal Circuit between Navigation ECU and Combination Meter

DESCRIPTION

The navigation ECU receives a vehicle speed signal from the combination meter assembly.

HINT:

  • A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls its respective systems based on this pulse signal.
  • If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the following diagram will not operate normally.

WIRING DIAGRAM

PROCEDURE

1.

CHECK COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)

(a) Check the output waveform.

(1) Remove the combination meter assembly with the connector(s) still connected.

Click here 2019 - 2022 MY RAV4 RAV4 HV [11/2018 - 10/2022]; METER / GAUGE / DISPLAY: COMBINATION METER: REMOVAL

(2) Connect an oscilloscope to terminal G18-36 (+S) and body ground.

(3) Turn the ignition switch to ON.

(4) Turn a wheel slowly.

(5) Check the signal waveform according to the condition(s) in the table below.

Item

Condition

Measurement terminal

G18-36 (+S) - Body ground

Tool setting

5 V/DIV., 20 ms./DIV.

Vehicle condition

Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.

HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.

*a

Component with harness connected

(Combination Meter Assembly)

NG

GO TO METER / GAUGE SYSTEM 2019 MY RAV4 RAV4 HV [11/2018 - 10/2019]; METER / GAUGE / DISPLAY: METER / GAUGE SYSTEM: Speed Signal Circuit 2020 MY RAV4 RAV4 HV [10/2019 - 08/2020]; METER / GAUGE / DISPLAY: METER / GAUGE SYSTEM: Speed Signal Circuit

OK

2.

CHECK HARNESS AND CONNECTOR (NAVIGATION ECU - COMBINATION METER ASSEMBLY)

  • *1: Only for models with the vehicle identification number on the certification label ending with the character A.

    *2: Except models with the vehicle identification number on the certification label ending with the character A.

(a) Disconnect the G15*1 or H7*2 navigation ECU connector.

(b) Disconnect the G18 combination meter assembly connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

G15-9 (SPD) - G18-36 (+S)*1

Always

Below 1 Ω

H7-9 (SPD) - G18-36 (+S)*2

Always

Below 1 Ω

OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE 2019 MY RAV4 RAV4 HV [11/2018 - 02/2019]; NAVIGATION / MULTI INFO DISPLAY: NAVIGATION SYSTEM: PROBLEM SYMPTOMS TABLE 2019 MY RAV4 RAV4 HV [02/2019 - 10/2019]; NAVIGATION / MULTI INFO DISPLAY: NAVIGATION SYSTEM: PROBLEM SYMPTOMS TABLE 2020 - 2022 MY RAV4 RAV4 HV [10/2019 - 10/2022]; NAVIGATION / MULTI INFO DISPLAY: NAVIGATION SYSTEM: PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR