Last Modified: 01-30-2024 |
6.11:8.1.0 |
Doc ID: RM100000001E7I6 |
Model Year Start: 2019 |
Model: RAV4 |
Prod Date Range: [11/2018 - 10/2022] |
Title: NAVIGATION / MULTI INFO DISPLAY: NAVIGATION SYSTEM: B15C0,B15C1; GPS Antenna Connection Malfunction(short); 2019 - 2022 MY RAV4 RAV4 HV [11/2018 - 10/2022] |
DTC
|
B15C0
|
GPS Antenna Connection Malfunction(short)
|
DTC
|
B15C1
|
GPS Antenna Connection Malfunction(break)
|
DESCRIPTION
These DTCs are stored when a malfunction occurs in the navigation antenna assembly.
DTC No.
|
Detection Item
|
DTC Detection Condition
|
Trouble Area
|
B15C0
|
GPS Antenna Connection Malfunction(short)
|
GPS Antenna Connection Malfunction(short)
|
-
Navigation antenna assembly
-
Antenna cord sub-assembly
-
No. 2 antenna cord sub-assembly
-
Navigation ECU
|
B15C1
|
GPS Antenna Connection Malfunction(break)
|
GPS Antenna Connection Malfunction(break)
|
-
Navigation antenna assembly
-
Antenna cord sub-assembly
-
No. 2 antenna cord sub-assembly
-
Navigation ECU
|
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
-
When replacing the navigation ECU, always replace it with a new one. If a navigation ECU which was installed to another vehicle is used, the following may occur:
-
A communication malfunction DTC may be stored.
-
The navigation ECU may not operate normally.
-
Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.
Click here
HINT:
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.
Click here
PROCEDURE
(a) Clear the DTCs.
Click here
Body Electrical > Navigation System > Clear DTCs
(b) Recheck for DTCs and check that no DTCs are output.
Click here
Body Electrical > Navigation System > Trouble Codes
OK:
No DTCs are output.
NG
|
|
|
2.
|
INSPECT NAVIGATION ANTENNA ASSEMBLY
|
(a) Remove the navigation antenna assembly.
Click here
(b) Inspect the navigation antenna assembly.
Click here
OK
|
|
|
3.
|
CHECK ANTENNA CORD SUB-ASSEMBLY
|
(a) Disconnect the antenna connector from the navigation antenna assembly.
|
|
*a
|
Front view of wire harness connector
(to Navigation Antenna Assembly)
|
*b
|
Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly)
|
|
|
(b) Disconnect the antenna connector from the No. 2 antenna cord sub-assembly.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
A-3 - B-6
|
Always
|
Below 1 Ω
|
A-3a - B-6a
|
Always
|
Below 1 Ω
|
A-3 - Body ground
|
Always
|
10 kΩ or higher
|
OK
|
|
|
4.
|
CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY
|
(a) Disconnect the antenna connector from the antenna cord sub-assembly.
|
|
*a
|
Front view of wire harness connector
(to Antenna Cord Sub-assembly)
|
*b
|
Front view of wire harness connector
(to Navigation ECU)
|
|
|
(b) Disconnect the antenna connector from the navigation ECU.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
B-6 - C-1 (GPS)
|
Always
|
Below 1 Ω
|
B-6a - C-1a
|
Always
|
Below 1 Ω
|
B-6 - Body ground
|
Always
|
10 kΩ or higher
|
|