Last Modified: 01-30-2024 |
6.11:8.1.0 |
Doc ID: RM100000001E4YE |
Model Year Start: 2019 |
Model: RAV4 |
Prod Date Range: [11/2018 - 10/2022] |
Title: AUDIO / VIDEO: AUDIO AND VISUAL SYSTEM: B15FE,B15FF; XM Tuner Antenna Disconnected; 2019 - 2022 MY RAV4 RAV4 HV [11/2018 - 10/2022] |
DTC
|
B15FE
|
XM Tuner Antenna Disconnected
|
DTC
|
B15FF
|
XM Tuner Antenna Short
|
DESCRIPTION
These DTCs are stored when a malfunction occurs in the No. 1 amplifier antenna assembly which is connected to the radio and display receiver assembly.
DTC No.
|
Detection Item
|
DTC Detection Condition
|
Trouble Area
|
B15FE
|
XM Tuner Antenna Disconnected
|
The No. 1 amplifier antenna assembly is not connected
|
-
No. 4 Antenna cord sub-assembly
-
No. 3 Antenna cord sub-assembly
-
Antenna cord sub-assembly
-
No. 1 amplifier antenna assembly
-
Radio and display receiver assembly
|
B15FF
|
XM Tuner Antenna Short
|
A short occurs in the No. 1 amplifier antenna assembly
|
-
No. 4 Antenna cord sub-assembly
-
No. 3 Antenna cord sub-assembly
-
Antenna cord sub-assembly
-
No. 1 amplifier antenna assembly
-
Radio and display receiver assembly
|
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occur:
-
A communication malfunction DTC may be stored.
-
The radio and display receiver assembly may not operate normally.
HINT:
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.
Click here
PROCEDURE
1.
|
CHECK CONNECTION OF ANTENNA CABLE
|
(a) Check if the No. 1 amplifier antenna assembly cable is securely connected to the radio and display receiver assembly.
OK:
No. 1 amplifier antenna assembly cable is securely connected.
NG |
|
SECURELY CONNECT NO. 1 AMPLIFIER ANTENNA ASSEMBLY CABLE
|
OK
|
|
|
(a) Clear the DTCs.
Click here
Body Electrical > Navigation System > Clear DTCs
(b) Recheck for DTCs and check that no DTCs are output.
Click here
Body Electrical > Navigation System > Trouble Codes
OK:
No DTCs are output.
NG
|
|
|
3.
|
CHECK NO. 4 ANTENNA CORD SUB-ASSEMBLY
|
(a) Disconnect the antenna connector from the No. 1 amplifier antenna assembly.
|
|
*a
|
Front view of wire harness connector
(No. 1 Amplifier Antenna Assembly)
|
*b
|
Front view of wire harness connector
(to No. 3 Antenna Cord Sub-assembly)
|
|
|
(b) Disconnect the antenna connector from the No. 3 antenna cord sub-assembly.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
A-3 - B-5
|
Always
|
Below 1 Ω
|
A-3a - B-5a
|
Always
|
Below 1 Ω
|
A-3 - Body ground
|
Always
|
10 kΩ or higher
|
OK
|
|
|
4.
|
CHECK NO. 3 ANTENNA CORD SUB-ASSEMBLY
|
(a) Disconnect the antenna connector from the No. 4 antenna cord sub-assembly.
|
|
*a
|
Front view of wire harness connector
(to No. 4 Antenna Cord Sub-assembly)
|
*b
|
Front view of wire harness connector
(to Antenna Cord Sub-assembly)
|
|
|
(b) Disconnect the antenna connector from the antenna cord sub-assembly.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
B-5 - C-5
|
Always
|
Below 1 Ω
|
B-5a - C-5a
|
Always
|
Below 1 Ω
|
B-5 - Body ground
|
Always
|
10 kΩ or higher
|
OK
|
|
|
5.
|
CHECK ANTENNA CORD SUB-ASSEMBLY
|
(a) Disconnect the antenna connector from the No. 3 antenna cord sub-assembly.
|
|
*a
|
Front view of wire harness connector
(to No. 3 Antenna Cord Sub-assembly)
|
*b
|
Front view of wire harness connector
(to Radio and Display Receiver Assembly)
|
|
|
(b) Disconnect the antenna connector from the radio and display receiver assembly.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
C-5 - D-1 (SXM)
|
Always
|
Below 1 Ω
|
C-5a - D-1a
|
Always
|
Below 1 Ω
|
C-5 - Body ground
|
Always
|
10 kΩ or higher
|
OK
|
|
|
6.
|
REPLACE NO. 1 AMPLIFIER ANTENNA ASSEMBLY
|
(a) Replace the No. 1 amplifier antenna assembly with a new or known good one.
Click here
(b) Clear the DTCs.
Click here
Body Electrical > Navigation System > Clear DTCs
(c) Recheck for DTCs and check that no DTCs are output.
Click here
Body Electrical > Navigation System > Trouble Codes
OK:
No DTCs are output.
OK |
|
END (NO. 1 AMPLIFIER ANTENNA ASSEMBLY IS DEFECTIVE)
|
|