| Last Modified: 08-21-2023 | 6.11:8.1.0 | Doc ID: RM100000001YV9G |
| Model Year Start: 2022 | Model: Avalon HV | Prod Date Range: [08/2021 - ] |
| Title: A25A-FXS (INTAKE / EXHAUST): INTAKE MANIFOLD: INSTALLATION; 2022 MY Avalon HV [08/2021 - ] | ||
INSTALLATION
CAUTION / NOTICE / HINT
NOTICE:
This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.
Click here
![2019 - 2022 MY Avalon Avalon HV [04/2018 - ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION](/t3Portal/stylegraphics/info.gif)
PROCEDURE
1. INSTALL VACUUM HOSE
(a) Install the vacuum hose to the intake manifold.
2. INSTALL NO. 1 ENGINE COVER
(a) Install the No. 1 engine cover with the clip.
3. INSTALL NO. 1 INTAKE MANIFOLD TO HEAD GASKET
(a) Install a new No. 1 intake manifold to head gasket to the intake manifold.
4. INSTALL INTAKE MANIFOLD
|
(a) Temporarily install the intake manifold to the cylinder head sub-assembly with the 5 bolts. |
|
(b) Tighten the 5 bolts in the order shown in the illustration.
Torque:
24 N·m {245 kgf·cm, 18 ft·lbf}
5. INSTALL NO. 2 FUEL VAPOR FEED HOSE
(a) Install the No. 2 fuel vapor feed hose to the intake manifold.
6. INSTALL NO. 2 WATER BY-PASS PIPE
|
(a) Temporarily install the No. 2 water by-pass pipe to the cylinder block sub-assembly with the bolt (B). |
|
(b) Using an 8 mm socket wrench, temporarily install the No. 2 water by-pass pipe to the intake manifold with the 2 bolts (A).
(c) Tighten the bolt (B).
Torque:
21 N·m {214 kgf·cm, 15 ft·lbf}
(d) Using the 8 mm socket wrench, tighten the 2 bolts (A).
Torque:
10 N·m {102 kgf·cm, 7 ft·lbf}
(e) Engage the wire harness clamp to connect the HV air conditioning wire.
7. CONNECT NO. 3 WATER BY-PASS PIPE
(a) Using an 8 mm socket wrench, connect the No. 3 water by-pass pipe to the intake manifold with the bolt.
Torque:
10 N·m {102 kgf·cm, 7 ft·lbf}
(b) Connect the No. 5 water by-pass hose to the No. 3 water by-pass pipe and slide the clip to secure it.
8. CONNECT ENGINE WIRE
|
(a) Engage the wire harness clamp to connect the engine wire to the intake manifold. |
|
(b) Install the bolt.
Torque:
10 N·m {102 kgf·cm, 7 ft·lbf}
|
(c) Connect the engine wire to the cylinder head sub-assembly with the bolt. Torque: 10 N·m {102 kgf·cm, 7 ft·lbf} |
|
(d) Connect the No. 5 engine wire connector.
9. INSTALL PURGE VALVE (PURGE VSV)
Click here
10. INSTALL NO. 1 EGR PIPE SUB-ASSEMBLY
Click here
11. CONNECT ENGINE WIRE
Click here
12. INSTALL E.F.I. VACUUM SENSOR ASSEMBLY (MANIFOLD ABSOLUTE PRESSURE SENSOR)
Click here
13. INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY
Click here
|
|