Last Modified: 08-21-2023 |
6.11:8.1.0 |
Doc ID: RM100000001YU1B |
Model Year Start: 2022 |
Model: Avalon HV |
Prod Date Range: [08/2021 -
] |
Title: HEATING / AIR CONDITIONING: AIR CONDITIONING UNIT (for HV Model): INSTALLATION; 2022 MY Avalon HV [08/2021 - ] |
INSTALLATION
PROCEDURE
1. TEMPORARILY INSTALL AIR CONDITIONER UNIT ASSEMBLY
(a) Engage the 2 claws.
(b) Temporarily install the air conditioner unit assembly to the instrument panel reinforcement assembly with the 3 bolts.
2. INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONER UNIT ASSEMBLY
Click here
3. INSTALL INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU
Click here
4. INSTALL HYBRID VEHICLE CONTROL ECU
Click here
5. INSTALL NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY
(a) Install the No. 3 instrument panel to cowl brace sub-assembly with the bolt and nut.
Torque:
Bolt :
10 N·m {102 kgf·cm, 7 ft·lbf}
Nut :
10 N·m {102 kgf·cm, 7 ft·lbf}
(b) Engage each clamp.
6. INSTALL NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY
(a) Install the No. 2 instrument panel brace sub-assembly with the bolt and nut.
Torque:
Bolt :
20 N·m {204 kgf·cm, 15 ft·lbf}
Nut :
18 N·m {184 kgf·cm, 13 ft·lbf}
(b) Temporarily install the screw.
HINT:
Do not fully tighten the screw.
(c) Engage each clamp.
(d) Connect the relay block holder with the bolt (A).
Torque:
8.0 N·m {82 kgf·cm, 71 in·lbf}
*a
|
Earth Wire
|
*b
|
Relay Block Holder
|
|
Bolt (A)
|
|
Bolt (B)
|
(e) Connect the earth wire with the bolt (B).
Torque:
8.5 N·m {87 kgf·cm, 75 in·lbf}
7. INSTALL NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY
Click here
8. INSTALL AIR CONDITIONER UNIT ASSEMBLY
(a) Tighten the 3 bolts, 2 screws and nut to install the air conditioner unit assembly.
Torque:
Bolt :
9.8 N·m {100 kgf·cm, 87 in·lbf}
Nut :
9.8 N·m {100 kgf·cm, 87 in·lbf}
NOTICE:
Tighten the bolts, screws and nut in the order shown in the illustration.
9. INSTALL NO. 3 DASH PANEL INSULATOR PAD
(a) Install the No. 3 dash panel insulator pad with 2 new clips as shown in the illustration.
|
|
10. INSTALL NO. 1 CONSOLE BOX DUCT
(a) Install the No. 1 console box duct as shown in the illustration.
|
Install in this Direction
|
11. INSTALL FLOOR CARPET BRACKET LH
(a) Engage the claw as shown in the illustration.
|
Install in this Direction
|
(b) Install the floor carpet bracket LH with the clip.
12. INSTALL FLOOR CARPET BRACKET RH
(a) Engage the claw as shown in the illustration.
|
Install in this Direction
|
(b) Install the floor carpet bracket RH with the clip.
13. INSTALL REAR NO. 3 AIR DUCT
(a) Engage the 2 claws to install the rear No. 3 air duct.
14. INSTALL REAR NO. 4 AIR DUCT
(a) Engage the 4 claws to install the rear No. 4 air duct as shown in the illustration.
|
Install in this Direction
|
(b) Install the front floor carpet assembly to its original position as shown in the illustration.
|
|
(c) Engage the 2 guides.
(d) Install the 3 front floor carpet clips.
15. INSTALL REAR NO. 1 AIR DUCT
(a) Engage the 2 claws to install the rear No. 1 air duct.
16. INSTALL REAR NO. 2 AIR DUCT
(a) Engage the 4 claws to install the rear No. 2 air duct as shown in the illustration.
|
Install in this Direction
|
(b) Install the front floor carpet assembly to its original position as shown in the illustration.
|
|
(c) Engage the 2 guides.
(d) Install the 3 front floor carpet clips.
17. INSTALL ACCELERATOR PEDAL
Click here
18. INSTALL ACCELERATOR PEDAL PAD
Click here
19. INSTALL COOLER (ROOM TEMP. SENSOR) THERMISTOR
(a) Connect the aspirator and connector to install the cooler (room temp. sensor) thermistor.
20. INSTALL NO. 1 CLEARANCE WARNING BUZZER (w/ Intelligent Parking Assist System)
Click here
21. INSTALL DCM (TELEMATICS TRANSCEIVER) WITH BRACKET
Click here
22. INSTALL VEHICLE APPROACHING SPEAKER CONTROLLER
Click here
23. INSTALL ECU INTEGRATION BOX RH
Click here
24. INSTALL INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY
Click here
25. INSTALL STEERING COLUMN ASSEMBLY
for Manual Tilt and Manual Telescopic Steering Column:
Click here
for Power Tilt and Power Telescopic Steering Column:
Click here
26. INSTALL TRANSMISSION FLOOR SHIFT ASSEMBLY
Click here
27. INSTALL FRONT SEAT ASSEMBLY LH
Click here
28. INSTALL FRONT SEAT ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
29. CONNECT AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY
(a) Remove the vinyl tape from the air conditioning tube and accessory assembly.
(b) Sufficiently apply compressor oil to a new O-ring and the fitting surface of the air conditioning tube and accessory assembly.
Compressor Oil:
ND-OIL 11 or equivalent
(c) Install the O-ring to the air conditioning tube and accessory assembly.
NOTICE:
Keep the O-ring and O-ring fitting surface free of foreign matter.
(d) Connect the air conditioning tube and accessory assembly.
30. CONNECT SUCTION PIPE SUB-ASSEMBLY
(a) Remove the vinyl tape from the suction pipe sub-assembly.
(b) Sufficiently apply compressor oil to a new O-ring and the fitting surface of the suction pipe sub-assembly.
Compressor Oil:
ND-OIL 11 or equivalent
(c) Install the O-ring to the suction pipe sub-assembly.
NOTICE:
Keep the O-ring and O-ring fitting surface free of foreign matter.
(d) Connect the suction pipe sub-assembly.
(e) Rotate the hook connector as shown in the illustration.
|
|
(f) Insert the tube joint into the fitting hole securely and install the bolt.
Torque:
9.8 N·m {100 kgf·cm, 87 in·lbf}
31. CONNECT INLET HEATER WATER HOSE
(a) Connect the inlet heater water hose with the marking facing up and engage the clip within the area shown in the illustration.
NOTICE:
Do not apply excessive force to the inlet heater water hose.
|
|
*a
|
View A
|
*b
|
Marking (White)
|
*c
|
Clip Installation Angle (270°)
|
|
|
32. CONNECT OUTLET HEATER WATER HOSE
(a) Connect the outlet heater water hose with the marking facing up and engage the clip within the area shown in the illustration.
NOTICE:
Do not apply excessive force to the outlet heater water hose.
|
|
*a
|
View A
|
*b
|
Marking (Green)
|
*c
|
Clip Installation Angle (270°)
|
|
|
33. INSTALL FRONT CENTER UPPER SUSPENSION BRACE SUB-ASSEMBLY
Click here
34. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
Click here
35. ADD ENGINE COOLANT (for Engine)
Click here
36. INSPECT FOR COOLANT LEAK (for Engine)
Click here
37. CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT
Click here
38. WARM UP COMPRESSOR
Click here
39. INSPECT FOR REFRIGERANT LEAK
Click here
|