Last Modified: 08-21-2023 |
6.11:8.1.0 |
Doc ID: RM100000001YP74 |
Model Year Start: 2022 |
Model: Avalon HV |
Prod Date Range: [08/2021 -
] |
Title: DOOR LOCK: REAR DOOR LOCK: REMOVAL; 2022 MY Avalon Avalon HV [08/2021 - ] |
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear door lock with motor assembly removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure
|
Necessary Procedure
|
Effect/Inoperative Function When Necessary Procedures are not Performed
|
Link
|
Disconnect cable from negative battery terminal
|
Perform steering sensor zero point calibration
|
Lane Tracing Assist System
|
|
Pre-collision System
|
Intelligent Clearance Sonar System*
|
Lighting System (for Gasoline Model with Cornering Light)
|
Memorize steering angle neutral point
|
Parking Assist Monitor System
|
|
Panoramic View Monitor System
|
|
-
Rear door glass sub-assembly
-
Rear door glass run
|
Initialize power window control system
|
-
Auto up and down function
-
Jam protection function
-
Remote control function
-
Key-linked function
-
Wireless transmitter-linked function
-
Key-off operation function
-
Catch protection function
-
Window open warning function
|
|
Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure
|
Necessary Procedure
|
Effect/Inoperative Function When Necessary Procedures are not Performed
|
Link
|
Disconnect cable from negative auxiliary battery terminal
|
Perform steering sensor zero point calibration
|
Lane Tracing Assist System
|
|
Pre-collision System
|
Intelligent Clearance Sonar System*
|
Lighting System (for HV Model with Cornering Light)
|
Memorize steering angle neutral point
|
Parking Assist Monitor System
|
|
Panoramic View Monitor System
|
|
-
Rear door glass sub-assembly
-
Rear door glass run
|
Initialize power window control system
|
-
Auto up and down function
-
Jam protection function
-
Remote control function
-
Key-linked function
-
Wireless transmitter-linked function
-
Key-off operation function
-
Catch protection function
-
Window open warning function
|
|
HINT:
-
Use the same procedure for the RH side and LH side.
-
The following procedure is for the LH side.
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the engine switch (for Gasoline Model) or power switch (for HV Model) off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here
2. REMOVE LUGGAGE TRIM SERVICE HOLE COVER (for HV Model)
Click here
3. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
for A25A-FKS:
Click here
for A25A-FXS:
Click here
for 2GR-FKS:
Click here
4. REMOVE REAR DOOR ARMREST COVER SUB-ASSEMBLY
Click here
5. REMOVE REAR DOOR TRIM ASSEMBLY COVER
Click here
6. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL
Click here
7. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY
Click here
8. REMOVE REAR DOOR NO. 1 TRIM BRACKET
Click here
9. REMOVE REAR DOOR SERVICE HOLE COVER
Click here
10. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP
Click here
11. REMOVE REAR DOOR NO. 2 SERVICE HOLE COVER
Click here
12. REMOVE REAR DOOR GLASS RUN
Click here
13. REMOVE REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY
Click here
14. REMOVE REAR DOOR GLASS SUB-ASSEMBLY
Click here
15. REMOVE REAR DOOR LOCK WITH MOTOR ASSEMBLY
(a) Using a T30 "TORX" socket wrench, remove the 3 screws.
*a
|
Release Plate
|
|
Remove in this Direction
|
(b) Move the rear door lock with motor assembly downward to disconnect it from the release plate of the rear door outside handle frame sub-assembly, and remove the rear door lock with motor assembly.
(c) When reusing the rear door lock with motor assembly:
(1) Remove the door lock wiring harness seal from the rear door lock with motor assembly.
|
|
16. REMOVE REAR DOOR LOCK OPEN LEVER REMOTE CONTROL CABLE
(a) Using a screwdriver, disengage the 2 claws and open the cover as shown in the illustration.
|
|
(b) Remove the rear door lock open lever remote control cable as shown in the illustration.
|
Remove in this Direction
|
17. REMOVE REAR DOOR INSIDE LOCK/UNLOCK KNOB LOCKING CABLE
(a) Using a screwdriver, disengage the 3 claws and open the cover as shown in the illustration.
|
|
(b) Remove the rear door inside lock/unlock knob locking cable as shown in the illustration.
|
Remove in this Direction
|
|