Last Modified: 08-21-2023 6.11:8.1.0 Doc ID: RM100000001YOZF
Model Year Start: 2022 Model: Avalon HV Prod Date Range: [08/2021 -           ]
Title: INTERIOR PANELS / TRIM: ROOF HEADLINING: REMOVAL; 2022 MY Avalon Avalon HV [08/2021 -        ]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during roof headlining removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function When Necessary Procedures are not Performed

Link

*: When performing learning using the Techstream.

Click here 2019 - 2022 MY Avalon [04/2018 -        ]; PARK ASSIST / MONITORING: INTELLIGENT CLEARANCE SONAR SYSTEM (for Gasoline Model): CALIBRATION

Disconnect cable from negative (-) battery terminal

Perform steering sensor zero point calibration

Lane Tracing Assist System

2022 MY Avalon Avalon HV [08/2021 -        ]; PRE-COLLISION: PRE-COLLISION SYSTEM: INITIALIZATION

Pre-collision System

Intelligent Clearance Sonar System*

Lighting System (for Gasoline Model with Cornering Light)

Memorize steering angle neutral point

Parking Assist Monitor System

2019 - 2022 MY Avalon [04/2018 -        ]; PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM (for Gasoline Model): INITIALIZATION

Panoramic View Monitor System

2019 - 2022 MY Avalon [04/2018 -        ]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM (for Gasoline Model): INITIALIZATION

Front passenger seat

Zero point calibration (Occupant classification system)

  • Occupant classification system
  • Passenger airbag ON/OFF indicator
  • Airbag system (Front passenger side)
  • Seat belt warning system (Front passenger)

2019 - 2022 MY Avalon [04/2018 -        ]; SUPPLEMENTAL RESTRAINT SYSTEMS: OCCUPANT CLASSIFICATION SYSTEM (for Gasoline Model): INITIALIZATION

Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function When Necessary Procedures are not Performed

Link

*: When performing learning using the Techstream.

Click here 2019 - 2022 MY Avalon HV [04/2018 -        ]; PARK ASSIST / MONITORING: INTELLIGENT CLEARANCE SONAR SYSTEM (for HV Model): CALIBRATION

Disconnect cable from negative (-) auxiliary battery terminal

Perform steering sensor zero point calibration

Lane Tracing Assist System

2022 MY Avalon Avalon HV [08/2021 -        ]; PRE-COLLISION: PRE-COLLISION SYSTEM: INITIALIZATION

Pre-collision System

Intelligent Clearance Sonar System*

Lighting System (for HV Model with Cornering Light)

Memorize steering angle neutral point

Parking Assist Monitor System

2019 - 2022 MY Avalon HV [04/2018 -        ]; PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM(for HV Model): INITIALIZATION

Panoramic View Monitor System

2019 - 2022 MY Avalon HV [04/2018 -        ]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM (for HV Model): INITIALIZATION

Front passenger seat

Zero point calibration (Occupant classification system)

  • Occupant classification system
  • Passenger airbag ON/OFF indicator
  • Airbag system (Front passenger side)
  • Seat belt warning system (Front passenger)

2019 - 2022 MY Avalon HV [04/2018 -        ]; SUPPLEMENTAL RESTRAINT SYSTEMS: OCCUPANT CLASSIFICATION SYSTEM (for HV Model): INITIALIZATION

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

for Gasoline Model: Click here 2021 - 2022 MY Avalon [08/2020 -        ]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (for Gasoline Model): PRECAUTION

for HV Model: Click here 2019 - 2022 MY Avalon HV [04/2018 -        ]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (for HV Model): PRECAUTION

PROCEDURE

1. REMOVE FRONT SEAT ASSEMBLY

Click here 2022 MY Avalon Avalon HV [08/2021 -        ]; SEAT: FRONT SEAT ASSEMBLY: REMOVAL

2. REMOVE REAR SEAT ASSEMBLY

Click here 2022 MY Avalon Avalon HV [08/2021 -        ]; SEAT: REAR SEAT ASSEMBLY: REMOVAL

3. REMOVE FRONT DOOR SCUFF PLATE LH

(a) Disengage the claw as shown in the illustration.

Place Hand Here

Remove in this Direction

HINT:

Use the same procedure for the front side and rear side.

(b) Disengage the 8 claws and guide to remove the front door scuff plate LH as shown in the illustration.

Remove in this Direction

4. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH

(a) Remove the clip.

Remove in this Direction

(b) Disengage the claw and clip to remove the cowl side trim sub-assembly LH as shown in the illustration.

5. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

Click here 2019 - 2022 MY Avalon Avalon HV [04/2018 -        ]; DOOR / HATCH: FRONT DOOR OPENING TRIM WEATHERSTRIP: REMOVAL+

6. REMOVE FRONT PILLAR GARNISH LH

(a) Apply protective tape around the front pillar garnish LH as shown in the illustration.

Protective Tape

(b) Pull the upper part of the front pillar garnish LH toward the inside of the cabin as shown in the illustration to disengage the front pillar garnish LH from the base of the front pillar garnish clip.

HINT:

Let the front pillar garnish LH hang from the front pillar garnish clip.

*1

Front Pillar Garnish Clip

Remove in this Direction

(c) While pushing the tabs of the front pillar garnish clip as shown in the illustration, disengage it.

*1

Front Pillar Garnish Clip

HINT:

When the front pillar garnish clip cannot be disengaged easily:

  1. While pushing the tab of the front pillar garnish clip shown in the illustration with your finger, move the front pillar garnish clip in the direction shown in the illustration.

    Move in this Direction

  2. While pulling the front pillar garnish clip as shown in the illustration, push the tab of the front pillar garnish clip shown in the illustration with a screwdriver and disengage the front pillar garnish clip.

    Pull in this Direction

(d) Disengage the front pillar garnish LH from the base of the front pillar garnish clip as shown in the illustration.

*1

Front Pillar Garnish Clip

Remove in this Direction

(e) While pushing the tabs of the front pillar garnish clip as shown in the illustration, disengage it.

*1

Front Pillar Garnish Clip

HINT:

When the front pillar garnish clip cannot be disengaged easily:

  1. While pushing the tab of the front pillar garnish clip shown in the illustration with your finger, move the front pillar garnish clip in the direction shown in the illustration.

    Move in this Direction

  2. While pulling the front pillar garnish clip as shown in the illustration, push the tab of the front pillar garnish clip shown in the illustration with a screwdriver and disengage the front pillar garnish clip.

    Pull in this Direction

(f) w/o Front No. 3 Speaker:

(1) Disengage the 2 guides to remove the front pillar garnish LH as shown in the illustration.

Remove in this Direction

(g) w/ Front No. 3 Speaker:

(1) Disengage the 2 guides as shown in the illustration.

(2) Disconnect the connector to remove the front pillar garnish LH.

(h) Remove the 2 front pillar garnish clips from the front pillar garnish LH.

(i) Protect the curtain shield airbag assembly LH.

(1) Cover the curtain shield airbag assembly LH with a protective cover, such as a cloth, and secure the edges of the cover with tape as shown in the illustration.

NOTICE:

Cover the curtain shield airbag assembly LH with a protective cover as soon as the front pillar garnish LH is removed.

*1

Curtain Shield Airbag Assembly LH

*a

Protective Cover

*b

Adhesive Tape

7. REMOVE REAR DOOR SCUFF PLATE LH (for Gasoline Model)

(a) Disengage the claw as shown in the illustration.

Place Hand Here

Remove in this Direction

(b) Disengage the 5 claws and guide to remove the rear door scuff plate LH as shown in the illustration.

Remove in this Direction

8. REMOVE REAR DOOR SCUFF PLATE LH (for HV Model)

(a) Disengage the claw as shown in the illustration.

Place Hand Here

Remove in this Direction

(b) Disengage the 5 claws, clip and guide to remove the rear door scuff plate LH as shown in the illustration.

Remove in this Direction

9. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

Click here 2019 - 2022 MY Avalon Avalon HV [04/2018 -        ]; DOOR / HATCH: REAR DOOR OPENING TRIM WEATHERSTRIP: REMOVAL+

10. REMOVE LAP BELT OUTER ANCHOR COVER (for LH Side)

Click here 2022 MY Avalon Avalon HV [08/2021 -        ]; SEAT BELT: FRONT SEAT OUTER BELT ASSEMBLY: REMOVAL+

11. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH

Click here 2022 MY Avalon Avalon HV [08/2021 -        ]; SEAT BELT: FRONT SEAT OUTER BELT ASSEMBLY: REMOVAL+

12. REMOVE CENTER PILLAR LOWER GARNISH LH

(a) Disengage the 2 claws as shown in the illustration.

Place Hand Here

Remove in this Direction

(b) Disengage the 3 clips to remove the center pillar lower garnish LH as shown in the illustration.

Remove in this Direction

13. REMOVE CENTER PILLAR UPPER GARNISH LH

(a) Using a clip remover, remove the 2 clips.

(b) Disengage the guide as shown in the illustration.

Place Hand Here

Remove in this Direction

(c) Disengage the clip and 2 guides as shown in the illustration.

Remove in this Direction

(d) Pass the anchor of the front seat outer belt assembly LH through the center pillar upper garnish LH and remove the center pillar upper garnish LH.

(e) Remove the clip from the center pillar upper garnish LH.

14. REMOVE ROOF SIDE RAIL GARNISH ASSEMBLY LH

(a) Disengage the claw as shown in the illustration.

Remove in this Direction

(b) Disengage the 2 claws and 3 guides as indicated by the arrows, in the order shown in the illustration to remove the roof side rail garnish assembly LH.

Remove in this Direction (1)

Remove in this Direction (2)

15. REMOVE ROOF SIDE INNER GARNISH LH

(a) Disengage the 3 clips as shown in the illustration.

Remove in this Direction

(b) Disengage the guide to remove the roof side inner garnish LH as shown in the illustration.

Remove in this Direction

(c) Remove the 3 clips from the roof side inner garnish LH.

16. REMOVE FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.

17. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.

18. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure as for the LH side.

19. REMOVE FRONT PILLAR GARNISH RH

HINT:

Use the same procedure as for the LH side.

20. REMOVE REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.

21. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure as for the LH side.

22. REMOVE LAP BELT OUTER ANCHOR COVER (for RH Side)

HINT:

Use the same procedure as for the LH side.

23. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.

24. REMOVE CENTER PILLAR LOWER GARNISH RH

HINT:

Use the same procedure as for the LH side.

25. REMOVE CENTER PILLAR UPPER GARNISH RH

HINT:

Use the same procedure as for the LH side.

26. REMOVE ROOF SIDE RAIL GARNISH ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.

27. REMOVE ROOF SIDE INNER GARNISH RH

HINT:

Use the same procedure as for the LH side.

28. REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY

Click here 2022 MY Avalon Avalon HV [08/2021 -        ]; INTERIOR PANELS / TRIM: INSTRUMENT PANEL SAFETY PAD: REMOVAL

29. REMOVE TRANSMISSION FLOOR SHIFT ASSEMBLY

for UA80E: Click here 2019 - 2022 MY Avalon [04/2018 -        ]; UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE): SHIFT LEVER: REMOVAL

for UB80F: Click here 2021 - 2022 MY Avalon [08/2020 -        ]; UB80F (AUTOMATIC TRANSMISSION / TRANSAXLE): SHIFT LEVER: REMOVAL

for P710: Click here 2019 - 2022 MY Avalon HV [04/2018 -        ]; P710 (HYBRID TRANSMISSION / TRANSAXLE): SHIFT LEVER: REMOVAL

30. REMOVE ROOF CONSOLE BOX ASSEMBLY

Click here 2019 - 2022 MY Avalon Avalon HV [04/2018 -        ]; LIGHTING (INT): PERSONAL LIGHT: REMOVAL+

31. REMOVE SPOT LIGHT ASSEMBLY

Click here 2019 - 2022 MY Avalon Avalon HV [04/2018 -        ]; LIGHTING (INT): ROOM LIGHT: REMOVAL+

32. REMOVE NO. 2 FORWARD RECOGNITION COVER

Click here 2022 MY Avalon Avalon HV [08/2021 -        ]; CRUISE CONTROL: FRONT CAMERA: REMOVAL+

33. REMOVE NO. 1 FORWARD RECOGNITION COVER

Click here 2022 MY Avalon Avalon HV [08/2021 -        ]; CRUISE CONTROL: FRONT CAMERA: REMOVAL+

34. REMOVE ASSIST GRIP SUB-ASSEMBLY

HINT:

Use the same procedure for all assist grip sub-assemblies.

(a) Insert SST into the cutout of the assist grip cover LH as shown in the illustration.

SST: 09813-00010

NOTICE:

To prevent the assist grip sub-assembly from being damaged, make sure to insert SST straight into the cutout.

HINT:

Use the same procedure for the LH side and RH side.

*a

Cutout

(b) Pull SST as shown in the illustration to disengage the claw.

NOTICE:

To prevent the assist grip sub-assembly from being damaged, make sure to only pull SST as shown in the illustration.

*a

30 to 45°

Remove in this Direction

HINT:

  • Use the same procedure for the claw on the other side of the assist grip cover LH.
  • Use the same procedure for the LH side and RH side.

(c) Remove the assist grip cover LH.

HINT:

Use the same procedure for the LH side and RH side.

(d) Disengage the 2 clips as shown in the illustration to remove the assist grip sub-assembly.

Remove in this Direction

(e) Remove the 2 clips from the vehicle body.

35. REMOVE REAR ASSIST GRIP ASSEMBLY LH

HINT:

Use the same procedure as for the assist grip sub-assembly.

36. REMOVE REAR ASSIST GRIP ASSEMBLY RH

HINT:

Use the same procedure as for the assist grip sub-assembly.

37. REMOVE VISOR BRACKET COVER LH

(a) Disengage the 4 claws and remove the visor bracket cover LH.

38. REMOVE VISOR ASSEMBLY LH

(a) for "TORX" Screw:

(1) Using a T25 "TORX" socket wrench, remove the 2 screws.

(b) except "TORX" Screw:

(1) Remove the 2 screws.

(c) Pull the visor assembly LH in the direction indicated by the arrow (1) shown in the illustration to disconnect it from the visor holder LH.

*1

Visor Holder LH

Remove in this Direction (1)

Remove in this Direction (2)

(d) Pull the visor assembly LH in the direction indicated by the arrow (2) shown in the illustration.

(e) Disconnect the connector to remove the visor assembly LH.

39. REMOVE VISOR HOLDER LH

(a) Turn the visor holder LH approximately 45° and remove it as indicated by the arrows, in the order shown in the illustration.

*a

45°

*b

Base of the Visor Holder LH

Remove in this Direction (1)

Remove in this Direction (2)

(b) Disengage the 2 claws to remove the base of the visor holder LH.

40. REMOVE VISOR BRACKET COVER RH

HINT:

Use the same procedure as for the LH side.

41. REMOVE VISOR ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.

42. REMOVE VISOR HOLDER RH

HINT:

Use the same procedure as for the LH side.

43. REMOVE SUN ROOF OPENING TRIM MOULDING (for Moon Roof)

(a) Remove the sun roof opening trim moulding.

44. REMOVE ROOF HEADLINING ASSEMBLY

(a) for Windshield Glass Side:

(1) Disconnect each connector.

(b) for Front Pillar LH Side:

(1) Remove the protective cover.

(2) Disconnect the 2 connectors.

(3) Using a clip remover, disengage the 4 clamps.

(4) Install the protective cover.

(c) for Front Pillar RH Side:

(1) Remove the protective cover.

(2) Remove the bolt.

*a

Guide

*b

Clamp

(3) Disengage the guide to disconnect the connector bracket.

(4) Using a clip remover, disengage the 2 clamps.

(5) Install the protective cover.

(d) for Rear Pillar LH Side:

(1) Disconnect the connector.

(2) Disengage the guide.

(e) for Rear Pillar RH Side:

(1) Disconnect each connector.

(2) Disengage the guide.

(f) for Roof Side (for Normal Roof):

(1) Slide the roof headlining assembly to disengage it from the 4 clips as shown in the illustration.

Remove in this Direction

-

-

HINT:

Leave the 4 clips installed to the vehicle body.

(g) for Roof Side (for Moon Roof):

(1) Disconnect the connector.

Remove in this Direction

-

-

(2) Slide the roof headlining assembly to disengage it from the 4 clips as shown in the illustration.

HINT:

Leave the 4 clips installed to the vehicle body.

(h) Remove the roof headlining assembly from the vehicle through the front door RH as shown in the illustration.

Remove in this Direction

-

-

NOTICE:

Do not damage the roof headlining assembly or vehicle interior.

(i) Remove the 4 clips from the vehicle body as shown in the illustration.

Remove in this Direction