| Last Modified: 08-21-2023 | 6.11:8.1.0 | Doc ID: RM100000001YOKE |
| Model Year Start: 2022 | Model: Avalon HV | Prod Date Range: [08/2021 - ] |
| Title: HYBRID / BATTERY CONTROL: BATTERY PLUG (for LITHIUM-ION BATTERY): REMOVAL; 2022 MY Avalon HV [08/2021 - ] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during electric vehicle battery plug assembly removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function when Necessary Procedure not Performed |
Link |
|---|---|---|---|
|
*: When performing learning using the Techstream.
Click here
|
|||
|
Auxiliary battery terminal is disconnected/reconnected |
Perform steering sensor zero point calibration |
Lane Tracing Assist System |
|
|
Pre-collision system |
|||
|
Intelligent clearance sonar system* |
|||
|
Lighting System (for HV Model with Cornering Light) |
|||
|
Memorize steering angle neutral point |
Parking assist monitor system |
|
|
|
Panoramic view monitor system |
|
||
CAUTION:
-
Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.
Click here
![2022 MY Avalon HV [08/2021 - ]; HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY): PRECAUTION](/t3Portal/stylegraphics/info.gif)
-
To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.
NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here
PROCEDURE
1. REMOVE SERVICE PLUG GRIP
Click here
2. DISCONNECT ENGINE ROOM MAIN WIRE
Click here
3. REMOVE CONNECTOR COVER ASSEMBLY
Click here
4. CHECK TERMINAL VOLTAGE
Click here
5. INSTALL CONNECTOR COVER ASSEMBLY
Click here
6. CONNECT ENGINE ROOM MAIN WIRE
Click here
7. DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY
Click here
8. REMOVE REAR SEAT CUSHION ASSEMBLY
Click here
9. REMOVE REAR SEAT CUSHION LOCK HOOK
Click here
10. REMOVE REAR DOOR SCUFF PLATE LH
Click here
11. REMOVE REAR UNDER SIDE COVER LH
Click here
12. REMOVE REAR DOOR SCUFF PLATE RH
HINT:
Use the same procedure as for the LH side.
13. REMOVE REAR UNDER SIDE COVER RH
Click here
14. REMOVE REAR UNDER COVER
Click here
15. REMOVE REAR SEAT CUSHION LEG SUB-ASSEMBLY
Click here
16. REMOVE NO. 1 HV BATTERY COVER PANEL RH
Click here
17. REMOVE ELECTRIC VEHICLE BATTERY PLUG ASSEMBLY
CAUTION:
Be sure to wear insulated gloves and protective goggles.
|
(a) Disconnect the electric vehicle battery plug assembly connector. |
|
|
(b) Disengage the 2 claws and open the wiring harness protector. |
|
|
(c) Disconnect the HV battery junction block assembly connector. NOTICE: Insulate the disconnected high-voltage connector with insulating tape. |
|
(d) Disconnect the hybrid battery terminal block connector.
NOTICE:
Insulate the disconnected high-voltage connector with insulating tape.
|
(e) Remove the bolt and electric vehicle battery plug assembly from the HV battery. |
|
|
|