Last Modified: 08-21-2023 6.11:8.1.0 Doc ID: RM100000001YO64
Model Year Start: 2022 Model: Avalon Prod Date Range: [08/2021 -           ]
Title: 2GR-FKS (FUEL): FUEL PRESSURE SENSOR (for High Pressure): REMOVAL; 2022 MY Avalon [08/2021 -        ]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel pressure sensor (fuel delivery pipe with sensor assembly LH) removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link
*: When performing learning using the Techstream.

Click here 2019 - 2022 MY Avalon [04/2018 -        ]; PARK ASSIST / MONITORING: INTELLIGENT CLEARANCE SONAR SYSTEM (for Gasoline Model): CALIBRATION

Battery terminal is disconnected/reconnected

Perform steering sensor zero point calibration

Lane Tracing Assist System

2022 MY Avalon Avalon HV [08/2021 -        ]; PRE-COLLISION: PRE-COLLISION SYSTEM: INITIALIZATION

Pre-collision System

Intelligent Clearance Sonar System*

Lighting System (for Gasoline Model with Cornering Light)

Memorize steering angle neutral point

Parking Assist Monitor System

2019 - 2022 MY Avalon [04/2018 -        ]; PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM (for Gasoline Model): INITIALIZATION

Panoramic View Monitor System

2019 - 2022 MY Avalon [04/2018 -        ]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM (for Gasoline Model): INITIALIZATION

  • Replacement of fuel pressure sensor (fuel delivery pipe with sensor assembly LH)
  • Replacement of fuel injector assembly (for Port Injection)
  • Replacement of fuel injector assembly (for Direct Injection)
  • Replacement of throttle body with motor assembly
  • Cleaning the deposits from the throttle body with motor assembly

Inspection after repair
  • Poor idle, etc.
  • Engine start function, etc.

2020 - 2022 MY Avalon [08/2019 -        ]; 2GR-FKS (ENGINE CONTROL): SFI SYSTEM: INITIALIZATION

CAUTION:

  • Never perform work on fuel system components near any possible ignition sources.
  • Vaporized fuel could ignite, resulting in a serious accident.
  • Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.
  • Sparks could cause vaporized fuel to ignite, resulting in a serious accident.

PROCEDURE

1. REMOVE FUEL PRESSURE SENSOR (FUEL DELIVERY PIPE WITH SENSOR ASSEMBLY LH)

Click here 2022 MY Avalon [08/2021 -        ]; 2GR-FKS (FUEL): FUEL INJECTOR (for Direct Injection): REMOVAL

NOTICE:

  • Do not remove the fuel pressure sensor from the fuel delivery pipe with sensor assembly LH.
  • If the fuel pressure sensor is removed, replace the fuel pressure sensor (fuel delivery pipe with sensor assembly LH) with a new one.

2. REMOVE FUEL PIPE PLUG SUB-ASSEMBLY

(a) Secure the fuel delivery pipe with sensor assembly LH in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.

(b) Using a 5 mm hexagon socket wrench, remove the 2 bolts, gasket and fuel pipe plug sub-assembly from the fuel delivery pipe with sensor assembly LH.

(c) w/ Dust Cap:

(1) Remove the dust cap sub-assembly from the fuel pipe plug sub-assembly.

(d) Remove the O-ring, No. 1 fuel injector back-up ring, No. 2 fuel injector back-up ring and No. 3 fuel injector back-up ring from the fuel pipe plug sub-assembly.

(e) Remove the fuel delivery pipe with sensor assembly LH from the vise.