Last Modified: 08-21-2023 |
6.11:8.1.0 |
Doc ID: RM100000001YNDQ |
Model Year Start: 2022 |
Model: Avalon HV |
Prod Date Range: [08/2021 -
] |
Title: HEATING / AIR CONDITIONING: AIR CONDITIONING UNIT (for HV Model): REMOVAL; 2022 MY Avalon HV [08/2021 - ] |
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during air conditioning unit removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure
|
Necessary Procedure
|
Effect/Inoperative Function When Necessary Procedures are not Performed
|
Link
|
Disconnect cable from negative auxiliary battery terminal
|
Perform steering sensor zero point calibration
|
Lane Tracing Assist System
|
|
Pre-collision System
|
Intelligent Clearance Sonar System*1
|
Lighting System (for HV Model with Cornering Light)
|
Memorize steering angle neutral point
|
Parking Assist Monitor System
|
|
Panoramic View Monitor System
|
|
Steering sensor
|
Steering angle zero point learning (Initialize intelligent clearance sonar system)
|
-
Intelligent Clearance Sonar System
-
Intuitive Parking Assist System
|
|
-
Steering angle zero point learning (Initialize parking assist monitor system)
-
Steering angle setting
|
Parking Assist Monitor System
|
for Initialization
for Calibration
|
Steering angle zero point learning (Initialize panoramic view monitor system)
|
Panoramic View Monitor System
|
for Initialization
for Calibration
|
Front passenger seat
|
Zero point calibration (Occupant classification system)
|
-
Occupant classification system
-
Passenger airbag ON/OFF indicator
-
Airbag system (Front passenger side)
-
Seat belt warning system (Front passenger)
|
|
CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.
Click here
PROCEDURE
1. PRECAUTION
NOTICE:
Make sure to select face mode before disconnecting the cable from the negative (-) auxiliary battery terminal.
2. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
Click here
3. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
Click here
4. REMOVE FRONT CENTER UPPER SUSPENSION BRACE SUB-ASSEMBLY
Click here
5. DISCONNECT OUTLET HEATER WATER HOSE
(a) Using pliers, grip the claws of the clip and slide the clip to disconnect the outlet heater water hose.
NOTICE:
-
Do not apply excessive force to the outlet heater water hose.
-
Prepare a drain pan or cloth in case the coolant leaks.
|
|
6. DISCONNECT INLET HEATER WATER HOSE
(a) Using pliers, grip the claws of the clip and slide the clip to disconnect the inlet heater water hose.
NOTICE:
-
Do not apply excessive force to the inlet heater water hose.
-
Prepare a drain pan or cloth in case the coolant leaks.
|
|
7. DISCONNECT SUCTION PIPE SUB-ASSEMBLY
(a) Remove the bolt and rotate the hook connector as shown in the illustration.
|
|
(b) Disconnect the suction pipe sub-assembly.
|
|
(c) Remove the O-ring from the suction pipe sub-assembly.
NOTICE:
Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.
8. DISCONNECT AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY
(a) Disconnect the air conditioning tube and accessory assembly.
|
|
(b) Remove the O-ring from the air conditioning tube and accessory assembly.
NOTICE:
Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.
9. REMOVE FRONT SEAT ASSEMBLY LH
Click here
10. REMOVE FRONT SEAT ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
11. REMOVE TRANSMISSION FLOOR SHIFT ASSEMBLY
Click here
12. REMOVE STEERING COLUMN ASSEMBLY
for Manual Tilt and Manual Telescopic Steering Column:
Click here
for Power Tilt and Power Telescopic Steering Column:
Click here
13. REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY
Click here
14. REMOVE ECU INTEGRATION BOX RH
Click here
15. REMOVE VEHICLE APPROACHING SPEAKER CONTROLLER
Click here
16. REMOVE DCM (TELEMATICS TRANSCEIVER) WITH BRACKET
Click here
17. REMOVE NO. 1 CLEARANCE WARNING BUZZER (w/ Intelligent Parking Assist System)
Click here
18. REMOVE COOLER (ROOM TEMP. SENSOR) THERMISTOR
(a) Disconnect the connector and aspirator to remove the cooler (room temp. sensor) thermistor.
|
|
19. REMOVE ACCELERATOR PEDAL PAD
Click here
20. REMOVE ACCELERATOR PEDAL
Click here
21. REMOVE REAR NO. 2 AIR DUCT
(a) Remove the front floor carpet clip.
|
|
(b) Remove the 2 front floor carpet clips.
|
|
(c) Disengage the 2 guides and turn back the front floor carpet assembly as shown in the illustration.
|
|
(d) Disengage the 4 claws and remove the rear No. 2 air duct as shown in the illustration.
|
Remove in this Direction
|
22. REMOVE REAR NO. 1 AIR DUCT
(a) Disengage the 2 claws and remove the rear No. 1 air duct.
|
|
23. REMOVE REAR NO. 4 AIR DUCT
(a) Remove the front floor carpet clip.
|
|
(b) Remove the 2 front floor carpet clips.
|
|
(c) Disengage the 2 guides and turn back the front floor carpet assembly as shown in the illustration.
|
|
(d) Disengage the 4 claws and remove the rear No. 4 air duct as shown in the illustration.
|
Remove in this Direction
|
24. REMOVE REAR NO. 3 AIR DUCT
(a) Disengage the 2 claws and remove the rear No. 3 air duct.
|
|
25. REMOVE FLOOR CARPET BRACKET RH
(a) Remove the clip.
|
Remove in this Direction
|
(b) Disengage the claw to remove the floor carpet bracket RH as shown in the illustration.
26. REMOVE FLOOR CARPET BRACKET LH
(a) Remove the clip.
|
Remove in this Direction
|
(b) Disengage the claw to remove the floor carpet bracket LH as shown in the illustration.
27. REMOVE NO. 1 CONSOLE BOX DUCT
(a) Remove the No. 1 console box duct as shown in the illustration.
|
Remove in this Direction
|
28. REMOVE NO. 3 DASH PANEL INSULATOR PAD
(a) Cut each claw of the 2 clips and remove the No. 3 dash panel insulator pad.
NOTICE:
If the No. 3 dash panel insulator pad is damaged, replace it with a new one.
|
|
(b) Remove the 2 clips.
29. REMOVE NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY
Click here
30. REMOVE NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY
(a) Remove the bolt (A) and disconnect the earth wire.
*a
|
Earth Wire
|
*b
|
Relay Block Holder
|
|
Bolt (A)
|
|
Bolt (B)
|
(b) Remove the bolt (B).
(c) Disengage each clamp to separate the relay block holder.
(d) Remove the bolt, screw, nut and No. 2 instrument panel brace sub-assembly.
31. REMOVE NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY
(a) Disengage each clamp.
|
Bolt
|
|
Nut
|
(b) Remove the bolt, nut and No. 3 instrument panel to cowl brace sub-assembly.
32. REMOVE HYBRID VEHICLE CONTROL ECU
Click here
33. REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU
Click here
34. REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONER UNIT ASSEMBLY
Click here
35. REMOVE AIR CONDITIONER UNIT ASSEMBLY
(a) Remove the 3 bolts.
(b) Disengage the 2 claws and remove the air conditioner unit assembly from the instrument panel reinforcement assembly.
|