| Last Modified: 08-21-2023 | 6.11:8.1.0 | Doc ID: RM100000001YLGR |
| Model Year Start: 2022 | Model: Avalon HV | Prod Date Range: [08/2021 - ] |
| Title: METER / GAUGE / DISPLAY: COMBINATION METER: REMOVAL; 2022 MY Avalon Avalon HV [08/2021 - ] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during combination meter assembly removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function When Necessary Procedures are not Performed |
Link |
|---|---|---|---|
|
*1: When performing learning using the Techstream.
Click here
|
|||
|
Disconnect cable from negative (-) battery terminal |
Perform steering sensor zero point calibration |
Lane Tracing Assist System |
|
|
Pre-collision System |
|||
|
Intelligent Clearance Sonar System*1 |
|||
|
Lighting System (for Gasoline Model with Cornering Light) |
|||
|
Memorize steering angle neutral point |
Parking Assist Monitor System |
|
|
|
Panoramic View Monitor System |
|
||
Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function When Necessary Procedures are not Performed |
Link |
|---|---|---|---|
|
*1: When performing learning using the Techstream.
Click here
|
|||
|
Disconnect cable from negative (-) auxiliary battery terminal |
Perform steering sensor zero point calibration |
Lane Tracing Assist System |
|
|
Pre-collision System |
|||
|
Intelligent Clearance Sonar System*1 |
|||
|
Lighting System (for HV Model with Cornering Light) |
|||
|
Memorize steering angle neutral point |
Parking Assist Monitor System |
|
|
|
Panoramic View Monitor System |
|
||
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the engine switch (for Gasoline Model) or power switch (for HV Model) off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here
![2019 - 2022 MY Avalon Avalon HV [04/2018 - ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION](/t3Portal/stylegraphics/info.gif)
2. CHANGE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM SETTINGS (for Power Tilt and Power Telescopic Steering Column)
Click here
3. REMOVE LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY
Click here
4. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL LH
Click here
5. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL RH
Click here
6. REMOVE FRONT CONSOLE UPPER PANEL GARNISH
Click here
7. REMOVE CONSOLE BOX POCKET SUB-ASSEMBLY
Click here
8. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
Click here
9. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY
for UA80E:
Click here
for UB80F:
Click here
10. REMOVE REAR UPPER CONSOLE PANEL SUB-ASSEMBLY
Click here
11. REMOVE CONSOLE BOX BEZEL
Click here
12. REMOVE CENTER NO. 1 INSTRUMENT CLUSTER FINISH PANEL
Click here
13. REMOVE CENTER NO. 2 INSTRUMENT CLUSTER FINISH PANEL
Click here
14. REMOVE RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET
Click here
15. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY
Click here
16. REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL
Click here
17. REMOVE LOWER CENTER INSTRUMENT PANEL FINISH PANEL
Click here
18. REMOVE INSTRUMENT CLUSTER FINISH PANEL GARNISH ASSEMBLY
Click here
19. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY
Click here
20. REMOVE NO. 1 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY
Click here
21. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
Click here
22. REMOVE COMBINATION METER ASSEMBLY
|
(a) Remove the 3 screws. |
|
(b) Disengage the 2 clips as shown in the illustration.
|
Remove in this Direction |
|
(c) Disengage the clamp. |
|
(d) Disconnect the 2 connectors to remove the combination meter assembly.
|
|