| Last Modified: 08-21-2023 | 6.11:8.1.0 | Doc ID: RM100000001YKUF |
| Model Year Start: 2022 | Model: Avalon HV | Prod Date Range: [08/2021 - ] |
| Title: PARK ASSIST / MONITORING: REAR CROSSING TRAFFIC ALERT BUZZER: REMOVAL; 2022 MY Avalon Avalon HV [08/2021 - ] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during blind spot monitor buzzer removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function When Necessary Procedures are not Performed |
Link |
|---|---|---|---|
|
*: When performing learning using the Techstream.
Click here
|
|||
|
Disconnect cable from negative battery terminal |
Perform steering sensor zero point calibration |
Lane Tracing Assist System |
|
|
Pre-collision System |
|||
|
Intelligent Clearance Sonar System* |
|||
|
Lighting System (for Gasoline Model with Cornering Light) |
|||
|
Memorize steering angle neutral point |
Parking Assist Monitor System |
|
|
|
Panoramic View Monitor System |
|
||
CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.
Click here
![2021 - 2022 MY Avalon [08/2020 - ]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (for Gasoline Model): PRECAUTION](/t3Portal/stylegraphics/info.gif)
Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function When Necessary Procedures are not Performed |
Link |
|---|---|---|---|
|
*: When performing learning using the Techstream.
Click here
|
|||
|
Disconnect cable from negative auxiliary battery terminal |
Perform steering sensor zero point calibration |
Lane Tracing Assist System |
|
|
Pre-collision System |
|||
|
Intelligent Clearance Sonar System* |
|||
|
Lighting System (for HV Model with Cornering Light) |
|||
|
Memorize steering angle neutral point |
Parking Assist Monitor System |
|
|
|
Panoramic View Monitor System |
|
||
CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.
Click here
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the engine switch (for Gasoline Model) or power switch (for HV Model) off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here
2. REMOVE LUGGAGE TRIM SERVICE HOLE COVER (for HV Model)
Click here
3. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
for A25A-FXS:
Click here
for 2GR-FKS:
Click here
for A25A-FKS:
Click here
CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
- If an airbag deploys for any reason, it may cause a serious injury.
4. REMOVE SPARE WHEEL COVER ASSEMBLY (w/ Seat Heater System)
Click here
5. REMOVE LUGGAGE COMPARTMENT INNER TRIM PAD (w/ Seat Heater System)
Click here
6. DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY
Click here
7. REMOVE REAR SEAT CUSHION ASSEMBLY
Click here
8. REMOVE REAR SEAT CUSHION LOCK HOOK
Click here
9. REMOVE REAR SIDE SEATBACK ASSEMBLY LH
Click here
10. REMOVE REAR SIDE SEATBACK ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
11. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH
Click here
12. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH
HINT:
Use the same procedure as for the LH side.
13. REMOVE ROOF SIDE RAIL GARNISH ASSEMBLY LH
Click here
14. REMOVE ROOF SIDE RAIL GARNISH ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
15. REMOVE ROOF SIDE INNER GARNISH LH
Click here
16. REMOVE ROOF SIDE INNER GARNISH RH
HINT:
Use the same procedure as for the LH side.
17. DISCONNECT REAR SEAT 3 POINT TYPE BELT ASSEMBLY LH
Click here
18. DISCONNECT REAR SEAT 3 POINT TYPE BELT ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
19. REMOVE CENTER STOP LIGHT SET
Click here
20. REMOVE REAR SEAT SHOULDER BELT COVER
Click here
21. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY
Click here
22. REMOVE BLIND SPOT MONITOR BUZZER
|
(a) Disengage the clamp. |
|
(b) Disconnect the connector to remove the blind spot monitor buzzer.
|
|