Last Modified: 08-21-2023 6.11:8.1.0 Doc ID: RM100000001YKOU
Model Year Start: 2022 Model: Avalon HV Prod Date Range: [08/2021 -           ]
Title: P710 (HYBRID TRANSMISSION / TRANSAXLE): MOTOR CABLE: REMOVAL; 2022 MY Avalon HV [08/2021 -        ]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during motor cable removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link
*: When performing learning using the Techstream.

Click here 2019 - 2022 MY Avalon HV [04/2018 -        ]; PARK ASSIST / MONITORING: INTELLIGENT CLEARANCE SONAR SYSTEM (for HV Model): CALIBRATION

Auxiliary battery terminal is disconnected/reconnected

Perform steering sensor zero point calibration

Lane Tracing Assist System

2022 MY Avalon Avalon HV [08/2021 -        ]; PRE-COLLISION: PRE-COLLISION SYSTEM: INITIALIZATION

Pre-collision System

Intelligent clearance sonar system*

Lighting system (w/ AFS)(EXT)

Memorize steering angle neutral point

Parking assist monitor system

2019 - 2022 MY Avalon HV [04/2018 -        ]; PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM(for HV Model): INITIALIZATION

Panoramic view monitor system

2019 - 2022 MY Avalon HV [04/2018 -        ]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM (for HV Model): INITIALIZATION

Replacement of ECM

Perform Vehicle Identification Number (VIN) registration

MIL illuminates

2019 - 2022 MY Avalon HV [04/2018 -        ]; A25A-FXS (ENGINE CONTROL): SFI SYSTEM: REGISTRATION

Replacement of inverter with converter assembly

Resolver learning
  • DTCs are stored
  • Slight vibration at a vehicle speed of 5 km/h (3 mph) or less
  • Shock or vibration during acceleration

2021 - 2022 MY Avalon HV [08/2020 -        ]; HYBRID / BATTERY CONTROL: MOTOR GENERATOR CONTROL SYSTEM (for LITHIUM-ION BATTERY): UTILITY

CAUTION:

  • Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.

    Click here 2022 MY Avalon HV [08/2021 -        ]; HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY): PRECAUTION

  • To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.

NOTICE:

  • After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

    Click here 2019 - 2022 MY Avalon Avalon HV [04/2018 -        ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION

  • If the ECM has been struck or dropped, replace it.
  • Perform Vehicle Identification Number (VIN) registration when replacing the ECM.

    Click here 2019 - 2022 MY Avalon HV [04/2018 -        ]; A25A-FXS (ENGINE CONTROL): SFI SYSTEM: REGISTRATION

PROCEDURE

1. REMOVE INVERTER WITH CONVERTER ASSEMBLY

Click here 2022 MY Avalon HV [08/2021 -        ]; HYBRID / BATTERY CONTROL: INVERTER WITH CONVERTER: REMOVAL

2. REMOVE MOTOR CABLE

CAUTION:

Be sure to wear insulated gloves.

(a) Remove the 2 bolts and connector cover from the hybrid vehicle transaxle assembly.

(b) Disengage the 2 claws to remove the terminal cap from the hybrid vehicle transaxle assembly.

(c) Using an insulated tool, remove the 6 bolts and motor cable from the hybrid vehicle transaxle assembly.

NOTICE:

  • Keep the motor cable terminals and their installation area free from foreign matter, water, etc.
  • Do not touch the waterproof seal or terminals of the motor cable.
  • Cover the hole where the motor cable was installed with tape or equivalent (non-residue type) to prevent entry of foreign matter.

*a

Waterproof Seal