- Front door glass sub-assembly
- Front door glass run
| Last Modified: 08-21-2023 | 6.11:8.1.0 | Doc ID: RM100000001RUZ7 |
| Model Year Start: 2021 | Model: Avalon HV | Prod Date Range: [08/2020 - 08/2021] |
| Title: EXTERIOR PANELS / TRIM: BLACK OUT TAPE (for Front Door): REMOVAL; 2021 MY Avalon Avalon HV [08/2020 - 08/2021] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during black out tape removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function When Necessary Procedures are not Performed |
Link |
|---|---|---|---|
|
*: When performing learning using the Techstream.
Click here
|
|||
|
Disconnect cable from negative battery terminal |
Perform steering sensor zero point calibration |
Lane Departure Alert System (w/ Steering Control) |
|
|
Pre-collision System |
|||
|
Intelligent Clearance Sonar System* |
|||
|
Lighting System (for Gasoline Model with Cornering Light) |
|||
|
Memorize steering angle neutral point |
Parking Assist Monitor System |
|
|
|
Panoramic View Monitor System |
|
||
|
|
Initialize power window control system |
|
|
Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function When Necessary Procedures are not Performed |
Link |
|---|---|---|---|
|
*: When performing learning using the Techstream.
Click here
|
|||
|
Disconnect cable from negative auxiliary battery terminal |
Perform steering sensor zero point calibration |
Lane Departure Alert System (w/ Steering Control) |
|
|
Pre-collision System |
|||
|
Intelligent Clearance Sonar System* |
|||
|
Lighting System (for HV Model with Cornering Light) |
|||
|
Memorize steering angle neutral point |
Parking Assist Monitor System |
|
|
|
Panoramic View Monitor System |
|
||
|
Initialize power window control system |
|
|
HINT:
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the engine switch (for Gasoline Model) or power switch (for HV Model) off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here
![2019 - 2022 MY Avalon Avalon HV [04/2018 - ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION](/t3Portal/stylegraphics/info.gif)
2. REMOVE LUGGAGE TRIM SERVICE HOLE COVER (for HV Model)
Click here
3. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
for A25A-FXS:
Click here
for 2GR-FKS:
Click here
for A25A-FKS:
Click here
4. REMOVE FRONT DOOR ARMREST COVER SUB-ASSEMBLY
Click here
5. REMOVE FRONT DOOR TRIM POCKET COVER
Click here
6. REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Driver Side)
Click here
7. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Front Passenger Side)
Click here
8. REMOVE COURTESY LIGHT ASSEMBLY
Click here
9. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY
Click here
10. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH
Click here
11. REMOVE FRONT DOOR TRIM BRACKET
Click here
12. REMOVE FRONT DOOR SERVICE HOLE COVER
Click here
13. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP
Click here
14. REMOVE FRONT DOOR PANEL PROTECTOR
Click here
15. REMOVE FRONT DOOR VENT SEAL
Click here
16. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY
Click here
17. REMOVE FRONT DOOR GLASS RUN
Click here
18. DISCONNECT FRONT DOOR WEATHERSTRIP
Click here
19. REMOVE DOOR FRAME GARNISH
Click here
20. REMOVE NO. 2 BLACK OUT TAPE
HINT:
When removing the No. 2 black out tape, heat the vehicle body and No. 2 black out tape using a heat light.
Heating Temperature
|
Item |
Temperature |
|---|---|
|
No. 2 Black Out Tape and Vehicle Body |
40 to 60°C (104 to 140°F) |
CAUTION:
- Do not touch the heat light and heated parts, touching the heat light may result in burns.
- Touching heated parts for a long time may result in burns.
|
*a |
Heated Part |
|
*b |
Heat Light |
NOTICE:
Do not heat the vehicle body excessively.
(a) Using a heat light, heat the No. 2 black out tape and vehicle body.
|
(b) Pull back on one of the ends of the No. 2 black out tape to remove it. HINT: When pulling on the No. 2 black out tape, pull it parallel to the vehicle body. |
|
21. REMOVE NO. 1 BLACK OUT TAPE
HINT:
When removing the No. 1 black out tape, heat the vehicle body and No. 1 black out tape using a heat light.
Heating Temperature
|
Item |
Temperature |
|---|---|
|
No. 1 Black Out Tape and Vehicle Body |
40 to 60°C (104 to 140°F) |
CAUTION:
- Do not touch the heat light and heated parts, touching the heat light may result in burns.
- Touching heated parts for a long time may result in burns.
|
*a |
Heated Part |
|
*b |
Heat Light |
NOTICE:
Do not heat the vehicle body excessively.
(a) Using a heat light, heat the No. 1 black out tape and vehicle body.
|
(b) Pull back on one of the ends of the No. 1 black out tape to remove it. HINT: When pulling on the No. 1 black out tape, pull it parallel to the vehicle body. |
|
|
|