| Last Modified: 08-21-2023 | 6.11:8.1.0 | Doc ID: RM100000001RUSI |
| Model Year Start: 2021 | Model: Avalon HV | Prod Date Range: [08/2020 - ] |
| Title: INTERIOR PANELS / TRIM: ROOF HEADLINING: INSTALLATION; 2021 - 2022 MY Avalon Avalon HV [08/2020 - ] | ||
INSTALLATION
PROCEDURE
1. INSTALL ROOF HEADLINING ASSEMBLY
|
(a) Install the 4 clips to the roof headlining assembly. |
|
(b) Put the roof headlining assembly into the vehicle through the front door RH as shown in the illustration.
|
Install in this Direction |
- |
- |
NOTICE:
Do not damage the roof headlining assembly or vehicle interior.
(c) for Roof Side (for Normal Roof):
(1) Engage the 2 claws to install the base of each visor holder.
|
*a |
Base of Visor Holder |
- |
- |
(2) Engage the 4 clips and install the roof headlining assembly.
(d) for Roof Side (for Moon Roof):
(1) Engage the 2 claws to install the base of each visor holder.
|
*a |
Base of Visor Holder |
- |
- |
(2) Engage the 4 clips and install the roof headlining assembly.
(3) Connect the connector.
(e) for Rear Pillar LH Side:
(1) Engage the guide.
(2) Connect the connector.
(f) for Rear Pillar RH Side:
(1) Engage the guide.
(2) Connect each connector.
(g) for Front Pillar LH Side:
(1) Remove the protective cover.
(2) Engage the 4 clamps.
(3) Connect the 2 connectors.
(4) Install the protective cover.
(h) for Front Pillar RH Side:
(1) Remove the protective cover.
(2) Engage the 2 clamps.
(3) Engage the guide.
(4) Connect the connector bracket with the bolt.
(5) Install the protective cover.
(i) for Windshield Glass Side:
(1) Connect each connector.
2. INSTALL SUN ROOF OPENING TRIM MOULDING (for Moon Roof)
|
(a) Align the alignment tape on the sun roof opening trim moulding with the notch of the roof headlining assembly and install the sun roof opening trim moulding. NOTICE: After installation, check that the corners fit correctly. |
|
3. INSTALL VISOR HOLDER LH
(a) Install the visor holder LH as shown in the illustration.
|
|
Install in this Direction |
4. INSTALL VISOR ASSEMBLY LH
NOTICE:
Make sure to install the visor assembly LH with its arrow facing the front of the vehicle.
(a) Connect the connector.
|
(b) Connect the visor assembly LH to the visor holder LH. |
|
(c) for "TORX" Screw:
(1) Using a T25 "TORX" socket wrench, install the visor assembly LH with the 2 screws.
(d) except "TORX" Screw:
(1) Install the visor assembly LH with the 2 screws.
5. INSTALL VISOR BRACKET COVER LH
(a) Engage the 4 claws to install the visor bracket cover LH.
6. INSTALL VISOR HOLDER RH
HINT:
Use the same procedure as for the LH side.
7. INSTALL VISOR ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
8. INSTALL VISOR BRACKET COVER RH
HINT:
Use the same procedure as for the LH side.
9. INSTALL ASSIST GRIP SUB-ASSEMBLY
HINT:
Use the same procedure for all assist grip sub-assemblies.
|
(a) Install the 2 clips to the assist grip. |
|
(b) Temporarily install the 2 assist grip covers to the assist grip as shown in the illustration.
(c) Engage the 2 clips to install the assist grip sub-assembly as shown in the illustration.
|
|
Install in this Direction |
|
(d) Engage the 4 claws to install the assist grip cover LH and assist grip cover RH. NOTICE: Make sure that the clip is engaged securely. |
|
10. INSTALL REAR ASSIST GRIP ASSEMBLY LH
HINT:
Use the same procedure as for the assist grip sub-assembly.
11. INSTALL REAR ASSIST GRIP ASSEMBLY RH
HINT:
Use the same procedure as for the assist grip sub-assembly.
12. INSTALL NO. 1 FORWARD RECOGNITION COVER
Click here
![2019 - 2021 MY Avalon Avalon HV [04/2018 - 08/2021]; CRUISE CONTROL: FRONT CAMERA: INSTALLATION+](/t3Portal/stylegraphics/info.gif)
13. INSTALL NO. 2 FORWARD RECOGNITION COVER
Click here
14. INSTALL SPOT LIGHT ASSEMBLY
Click here
15. INSTALL ROOF CONSOLE BOX ASSEMBLY
Click here
16. INSTALL TRANSMISSION FLOOR SHIFT ASSEMBLY
for UA80E: Click here
for UB80F: Click here
for P710: Click here
17. INSTALL INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY
Click here
18. INSTALL ROOF SIDE INNER GARNISH LH
(a) Install 3 new clips to the roof side inner garnish LH.
(b) Engage the guide as shown in the illustration.
|
|
Install in this Direction |
(c) Engage the 3 clips to install the roof side inner garnish LH as shown in the illustration.
|
|
Install in this Direction |
19. INSTALL ROOF SIDE RAIL GARNISH ASSEMBLY LH
(a) Engage the 3 guides and 3 claws as indicated by the arrows, in the order shown in the illustration to install the roof side rail garnish assembly LH.
|
|
Install in this Direction (1) |
|
Install in this Direction (2) |
20. INSTALL CENTER PILLAR UPPER GARNISH LH
(a) Install a new clip to the center pillar upper garnish LH.
(b) Engage the 3 guides and clip as shown in the illustration.
|
|
Install in this Direction |
(c) Install the center pillar upper garnish LH with the 2 clips.
21. INSTALL CENTER PILLAR LOWER GARNISH LH
(a) Engage the 2 claws and 3 clips to install the center pillar lower garnish LH as shown in the illustration.
|
|
Install in this Direction |
22. CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH
Click here
23. INSTALL LAP BELT OUTER ANCHOR COVER (for LH Side)
Click here
24. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH
Click here
25. INSTALL REAR DOOR SCUFF PLATE LH (for Gasoline Model)
(a) Engage the guide and 6 claws to install the rear door scuff plate LH as shown in the illustration.
|
|
Install in this Direction |
26. INSTALL REAR DOOR SCUFF PLATE LH (for HV Model)
(a) Engage the guide, 6 claws and clip to install the rear door scuff plate LH as shown in the illustration.
|
|
Install in this Direction |
27. INSTALL FRONT PILLAR GARNISH LH
(a) Remove the protective cover.
|
(b) Install 2 new front pillar garnish clips to the front pillar garnish LH. HINT: Make sure that the front pillar garnish clip is engaged correctly. |
|
(c) w/o Front No. 3 Speaker:
(1) Push the front pillar garnish LH as shown in the illustration to engage the 2 guides.
|
|
Install in this Direction |
(d) w/ Front No. 3 Speaker:
(1) Connect the connector.
(2) Push the front pillar garnish LH as shown in the illustration to engage the 2 guides.
(e) Engage the 2 front pillar garnish clips to install the front pillar garnish LH as shown in the illustration.
HINT:
Make sure that the curtain shield airbag assembly LH is not pinched.
|
*1 |
Front Pillar Garnish Clip |
|
|
Install in this Direction |
28. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
Click here
29. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH
(a) Engage the claw and clip as shown in the illustration.
|
|
Install in this Direction |
(b) Install the cowl side trim sub-assembly LH with the clip.
30. INSTALL FRONT DOOR SCUFF PLATE LH
(a) Engage the guide and 10 claws to install the front door scuff plate LH as shown in the illustration.
|
|
Install in this Direction |
31. INSTALL ROOF SIDE INNER GARNISH RH
HINT:
Use the same procedure as for the LH side.
32. INSTALL ROOF SIDE RAIL GARNISH ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
33. INSTALL CENTER PILLAR UPPER GARNISH RH
HINT:
Use the same procedure as for the LH side.
34. INSTALL CENTER PILLAR LOWER GARNISH RH
HINT:
Use the same procedure as for the LH side.
35. CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
36. INSTALL LAP BELT OUTER ANCHOR COVER (for RH Side)
HINT:
Use the same procedure as for the LH side.
37. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH
HINT:
Use the same procedure as for the LH side.
38. INSTALL REAR DOOR SCUFF PLATE RH
HINT:
Use the same procedure as for the LH side.
39. INSTALL FRONT PILLAR GARNISH RH
HINT:
Use the same procedure as for the LH side.
40. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
HINT:
Use the same procedure as for the LH side.
41. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
42. INSTALL FRONT DOOR SCUFF PLATE RH
HINT:
Use the same procedure as for the LH side.
43. INSTALL REAR SEAT ASSEMBLY
Click here
44. INSTALL FRONT SEAT ASSEMBLY
Click here
|
|