- Hybrid/EV Battery Cooling Fan 1 Drive Request
- Hybrid/EV Battery Cooling Fan 1 Drive Status
- Hybrid/EV Battery Cooling Fan 1 Frequency
| Last Modified: 08-21-2023 | 6.11:8.1.0 | Doc ID: RM100000001RK2A |
| Model Year Start: 2021 | Model: Avalon HV | Prod Date Range: [08/2020 - ] |
| Title: HYBRID / BATTERY CONTROL: HYBRID BATTERY SYSTEM (for LITHIUM-ION BATTERY): P0A8115; Hybrid/EV Battery Cooling Fan 1 Circuit Short to Auxiliary Battery or Open; 2021 - 2022 MY Avalon HV [08/2020 - ] | ||
|
DTC |
P0A8115 |
Hybrid/EV Battery Cooling Fan 1 Circuit Short to Auxiliary Battery or Open |
DESCRIPTION
Refer to the description for DTC P0A8111.
Click here
![2021 - 2022 MY Avalon HV [08/2020 - ]; HYBRID / BATTERY CONTROL: HYBRID BATTERY SYSTEM (for LITHIUM-ION BATTERY): P0A8111; Hybrid/EV Battery Cooling Fan 1 Circuit Short to Ground+](/t3Portal/stylegraphics/info.gif)
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
MIL |
Warning Indicate |
|---|---|---|---|---|---|
|
P0A8115 |
Hybrid/EV Battery Cooling Fan 1 Circuit Short to Auxiliary Battery or Open |
Both of the following conditions are met:
(1 trip detection logic) |
|
Comes on |
Master Warning Light: Comes on |
Related Data List
|
DTC No. |
Data List |
|---|---|
|
P0A8115 |
|
The following items can be helpful when performing repairs:
Data List
- Hybrid/EV Battery Temperature 1 to 6
- BATT Voltage
HINT:
- "Hybrid/EV Battery Cooling Fan 1 Frequency" is detected when the battery cooling blower assembly is operating and its value changes in proportion to the battery cooling blower assembly speed.
- If the battery cooling blower assembly speed is excessively high, this DTC is stored.
MONITOR DESCRIPTION
If the battery ECU assembly detects that the speed of the battery cooling blower assembly is higher than the target speed, it will illuminate the MIL and store a DTC.
MONITOR STRATEGY
|
Related DTCs |
P0A85 (INF P0A8115): Hybrid/EV Battery Cooling Fan 1 Circuit Short to Auxiliary Battery or Open |
|
Required sensors/components |
Battery cooling blower assembly |
|
Frequency of operation |
Continuous |
|
Duration |
TMC's intellectual property |
|
MIL operation |
1 driving cycle |
|
Sequence of operation |
None |
TYPICAL ENABLING CONDITIONS
|
The monitor will run whenever the following DTCs are not stored |
TMC's intellectual property |
|
Other conditions belong to TMC's intellectual property |
- |
TYPICAL MALFUNCTION THRESHOLDS
|
TMC's intellectual property |
- |
COMPONENT OPERATING RANGE
|
Battery ECU assembly |
DTC P0A85 (INF P0A8115) is not detected |
CONFIRMATION DRIVING PATTERN
HINT:
-
After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click here
-
When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
Click here
- Connect the Techstream to the DLC3.
- Turn the power switch on (IG) and turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the power switch off and wait for 2 minutes or more.
- Turn the power switch on (IG) and turn the Techstream on.
- Enter the following menus: Powertrain / HV Battery / Active Test / Control the Hybrid/EV Battery Cooling Fan.[*1]
-
Select fan mode 6 and operate the battery cooling blower assembly and wait for 60 seconds or more.[*2]
HINT:
- Operation of the battery cooling blower assembly can be confirmed by checking if air is sucked into the air intake port of the intake duct or by operation sounds.
-
[*1] to [*2]: Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
- Enter the following menus: Powertrain / HV Battery / Utility / All Readiness.
-
Check the DTC judgment result.
HINT:
- If the judgment result shows NORMAL, the system is normal.
- If the judgment result shows ABNORMAL, the system has a malfunction.
- If the judgment result shows INCOMPLETE or N/A, perform the normal judgment procedure again.
WIRING DIAGRAM
Refer to the wiring diagram for DTC P0A8111.
Click here
CAUTION / NOTICE / HINT
CAUTION:
-
Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.
- Inspecting the high-voltage system
- Disconnecting the low voltage connector of the inverter with converter assembly
- Disconnecting the low voltage connector of the HV battery
-
To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.
-
After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
-
After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.
Click here
HINT:
Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.
*a
Without waiting for 10 minutes
NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here
PROCEDURE
|
1. |
CHECK DTC OUTPUT (HV BATTERY, HYBRID CONTROL) |
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Enter the following menus: Powertrain / HV Battery and Hybrid Control / Trouble Codes.
(d) Check for DTCs.
Powertrain > HV Battery > Trouble Codes
Powertrain > Hybrid Control > Trouble Codes
|
Result |
Proceed to |
|---|---|
|
P0A8115 only is output, or DTCs except the ones in the table below are also output. |
A |
|
DTCs of hybrid battery system in the table below are output. |
B |
|
DTCs of hybrid control system in the table below are output. |
C |
|
System |
Relevant DTC |
|
|---|---|---|
|
Hybrid battery system |
P060A47 |
Hybrid/EV Battery Energy Control Module Monitoring Processor Watchdog / Safety MCU Failure |
|
P060B49 |
Hybrid/EV Battery Energy Control Module A/D Processing Internal Electronic Failure |
|
|
P060687 |
Hybrid/EV Battery Energy Control Module Processor to Monitoring Processor Missing Message |
|
|
Hybrid control system |
P0A1F94 |
Hybrid/EV Battery Energy Control Module Unexpected Operation |
(e) Turn the power switch off.
| B |
|
| C |
|
GO TO DTC CHART (HYBRID CONTROL SYSTEM)
|
|
|
2. |
CHECK BATTERY ECU ASSEMBLY (FREQUENCY) |
Click here
| OK |
|
| NG |
|
REPLACE BATTERY ECU ASSEMBLY
|
|
|