| Last Modified: 08-21-2023 | 6.11:8.1.0 | Doc ID: RM100000001RG5G |
| Model Year Start: 2021 | Model: Avalon HV | Prod Date Range: [08/2020 - ] |
| Title: SUPPLEMENTAL RESTRAINT SYSTEMS: CENTER AIRBAG SENSOR ASSEMBLY: INSTALLATION; 2021 - 2022 MY Avalon Avalon HV [08/2020 - ] | ||
INSTALLATION
PROCEDURE
1. INSTALL AIRBAG ECU ASSEMBLY
(a) Check that the engine switch (for Gasoline Model) or power switch (for HV Model) is off.
(b) Check that the cable is disconnected from the negative (-) auxiliary battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
|
(c) Install the airbag ECU assembly with the 3 bolts. Torque: 17.5 N·m {178 kgf·cm, 13 ft·lbf} NOTICE:
|
|
(d) Temporarily connect the connector and then move the lock lever in the direction indicated by the arrow to securely connect the connectors.
NOTICE:
When connecting any airbag connector, take care not to damage the airbag wire harness.
|
*a |
Lock Lever |
|
Move in this Direction |
(e) Check that there is no looseness in the installed parts of the airbag ECU assembly.
2. INSTALL NO. 1 CONSOLE BOX DUCT
(a) Install the No. 1 console box duct with the clip as shown in the illustration.
|
|
Install in this Direction |
3. INSTALL FRONT FLOOR CARPET ASSEMBLY
|
(a) Install the front floor carpet assembly to its original position as shown in the illustration. |
|
(b) Engage the 2 guides.
(c) Install the 3 front floor carpet clips.
|
(d) Install the front floor carpet assembly to its original position as shown in the illustration. |
|
(e) Engage the 2 guides.
(f) Install the 3 front floor carpet clips.
4. INSTALL ACCELERATOR PEDAL
for 2GR-FKS: Click here
![2019 - 2022 MY Avalon [04/2018 - ]; 2GR-FKS (ENGINE CONTROL): ACCELERATOR PEDAL: INSTALLATION+](/t3Portal/stylegraphics/info.gif)
for A25A-FXS: Click here
for A25A-FKS: Click here
5. INSTALL ACCELERATOR PEDAL PAD
for 2GR-FKS: Click here
for A25A-FXS: Click here
for A25A-FKS: Click here
6. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
Click here
7. INSTALL CENTER PILLAR LOWER GARNISH LH
Click here
8. CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH
9. INSTALL REAR DOOR SCUFF PLATE LH (for Gasoline Model)
Click here
10. INSTALL REAR DOOR SCUFF PLATE LH (for HV Model)
Click here
11. CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH
12. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH
Click here
13. INSTALL FRONT DOOR SCUFF PLATE LH
Click here
14. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
Click here
15. INSTALL CENTER PILLAR LOWER GARNISH RH
HINT:
Use the same procedure as for the LH side.
Click here
16. CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH
17. INSTALL REAR DOOR SCUFF PLATE RH (for Gasoline Model)
HINT:
Use the same procedure as for the LH side.
Click here
18. INSTALL REAR DOOR SCUFF PLATE RH (for HV Model)
HINT:
Use the same procedure as for the LH side.
Click here
19. CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH
20. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
Click here
21. INSTALL FRONT DOOR SCUFF PLATE RH
HINT:
Use the same procedure as for the LH side.
Click here
22. INSTALL REAR SEAT CUSHION LOCK HOOK (for Gasoline Model)
Click here
23. INSTALL REAR SEAT CUSHION ASSEMBLY (for Gasoline Model)
Click here
24. CONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY (for Gasoline Model)
Click here
25. INSTALL LUGGAGE COMPARTMENT INNER TRIM PAD (for Gasoline Model with Seat Heater System)
Click here
26. INSTALL SPARE WHEEL COVER ASSEMBLY (for Gasoline Model with Seat Heater System)
Click here
27. INSTALL CONSOLE ASSEMBLY
Click here
28. INSTALL FRONT SEAT ASSEMBLY
(a) Install the front seat assembly LH and front seat assembly RH.
Click here
29. PERFORM DIAGNOSTIC SYSTEM CHECK
for Gasoline Model: Click here
for HV Model: Click here
30. PERFORM INITIALIZATION
for Electronically Controlled Brake System (for Gasoline Model): Click here
for Electronically Controlled Brake System (for HV Model): Click here
for Dynamic Torque Control AWD System: Click here
|
|