Last Modified: 08-21-2023 6.11:8.1.0 Doc ID: RM100000001RFZ8
Model Year Start: 2021 Model: Avalon HV Prod Date Range: [08/2020 - 08/2021]
Title: STEERING COLUMN: TILT AND TELESCOPIC MANUAL SWITCH: REMOVAL; 2021 MY Avalon Avalon HV [08/2020 - 08/2021]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during tilt and telescopic switch removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link
*: When performing learning using the Techstream.

Click here 2019 - 2022 MY Avalon [04/2018 -        ]; PARK ASSIST / MONITORING: INTELLIGENT CLEARANCE SONAR SYSTEM (for Gasoline Model): CALIBRATION

Disconnect cable from negative auxiliary battery terminal

Perform steering sensor zero point calibration

Lane Departure Alert System (w/ Steering Control)

2019 - 2021 MY Avalon [04/2018 - 08/2021]; PRE-COLLISION: PRE-COLLISION SYSTEM (for Gasoline Model): INITIALIZATION

Pre-collision System

Intelligent Clearance Sonar System*

Lighting System (for Gasoline Model with Cornering Light)

Memorize steering angle neutral point

Parking Assist Monitor System

2019 - 2022 MY Avalon [04/2018 -        ]; PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM (for Gasoline Model): INITIALIZATION

Panoramic View Monitor System

2019 - 2022 MY Avalon [04/2018 -        ]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM (for Gasoline Model): INITIALIZATION

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link
*: When performing learning using the Techstream.

Click here 2019 - 2022 MY Avalon HV [04/2018 -        ]; PARK ASSIST / MONITORING: INTELLIGENT CLEARANCE SONAR SYSTEM (for HV Model): CALIBRATION

Disconnect cable from negative auxiliary battery terminal

Perform steering sensor zero point calibration

Lane Departure Alert System (w/ Steering Control)

2019 - 2021 MY Avalon HV [04/2018 - 08/2021]; PRE-COLLISION: PRE-COLLISION SYSTEM (for HV Model): INITIALIZATION

Pre-collision System

Intelligent Clearance Sonar System*

Lighting System (for HV Model with Cornering Light)

Memorize steering angle neutral point

Parking Assist Monitor System

2019 - 2022 MY Avalon HV [04/2018 -        ]; PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM(for HV Model): INITIALIZATION

Panoramic View Monitor System

2019 - 2022 MY Avalon HV [04/2018 -        ]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM (for HV Model): INITIALIZATION

PROCEDURE

1. CHANGE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM SETTINGS

Click here 2019 - 2021 MY Avalon Avalon HV [04/2018 - 08/2021]; STEERING COLUMN: STEERING COLUMN ASSEMBLY (for Power Tilt and Power Telescopic Steering Column): REMOVAL+

2. REMOVE LOWER STEERING COLUMN COVER

Click here 2019 - 2022 MY Avalon Avalon HV [04/2018 -        ]; WIPER / WASHER: WIPER SWITCH: REMOVAL+

3. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

for 2GR-FKS: Click here 2019 - 2021 MY Avalon [04/2018 - 08/2021]; MAINTENANCE: 2GR-FKS BATTERY: REMOVAL+

for A25A-FXS: Click here 2020 - 2021 MY Avalon HV [08/2019 - 08/2021]; MAINTENANCE: A25A-FXS AUXILIARY BATTERY: REMOVAL+

for A25A-FKS: Click here 2021 - 2022 MY Avalon [08/2020 -        ]; MAINTENANCE: A25A-FKS BATTERY: REMOVAL+

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click here 2021 MY Avalon Avalon HV [08/2020 - 08/2021]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION

4. REMOVE TILT AND TELESCOPIC SWITCH

(a) Disconnect the spiral cable connector from the spiral cable sub-assembly.

*1

Spiral Cable Connector

*2

Tilt and Telescopic Connector

(b) Disconnect the tilt and telescopic connector from the tilt and telescopic switch.

(c) Disengage the claw and pull out the tilt and telescopic switch.

*a

Claw

Pull out in this direction