Last Modified: 08-21-2023 6.11:8.1.0 Doc ID: RM100000001QM6J
Model Year Start: 2021 Model: Avalon HV Prod Date Range: [08/2020 -           ]
Title: LIGHTING (EXT): LIGHTING SYSTEM (for HV Model with Cornering Light): Back-up Light Circuit; 2021 - 2022 MY Avalon HV [08/2020 -        ]

Back-up Light Circuit

DESCRIPTION

The hybrid vehicle control ECU controls the back-up lights via the BKUP LP relay.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

  • Inspect the fuses for circuits related to this system before performing the following procedure.
  • Before replacing the hybrid vehicle control ECU, refer to Registration.

    Click here 2021 - 2022 MY Avalon HV [08/2020 -        ]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, HV Model): REGISTRATION

PROCEDURE

1.

CHECK FOR DTC

(a) Connect the Techstream to the DLC3.

(b) Turn the power switch on (IG).

(c) Turn the Techstream on.

(d) Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

(e) Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes

Result

Proceed to

Hybrid control system DTCs are not output

A

Hybrid control system DTCs are output

B

B

GO TO HYBRID CONTROL SYSTEM 2021 MY Avalon HV [08/2020 - 08/2021]; HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY): DIAGNOSTIC TROUBLE CODE CHART 2022 MY Avalon HV [08/2021 -        ]; HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY): DIAGNOSTIC TROUBLE CODE CHART

A

2.

CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BODY GROUND)

(a) Disconnect the 4D instrument panel junction block assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

4D-3 - Body ground

Always

Below 1 Ω

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

3.

CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

(a) Disconnect the 4F instrument panel junction block assembly connector.

(b) Disconnect the A24 hybrid vehicle control ECU connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

A24-2 (BL) - 4F-19

Always

Below 1 Ω

A24-2 (BL) or 4F-19 - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

4.

CHECK HYBRID VEHICLE CONTROL ECU (OUTPUT VOLTAGE)

*a

Component with harness connected

(Instrument Panel Junction Block Assembly)

(a) Connect the A24 hybrid vehicle control ECU connector.

(b) Connect the 4D and 4F instrument panel junction block assembly connectors.

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

4F-19 - Body ground

Power switch off, reverse (R) not selected

Below 1 V

4F-19 - Body ground

Power switch on (IG), reverse (R) selected

11 to 14 V

NG

REPLACE HYBRID VEHICLE CONTROL ECU 2019 - 2021 MY Avalon HV [04/2018 - 08/2021]; HYBRID / BATTERY CONTROL: HYBRID VEHICLE CONTROL ECU: REMOVAL 2022 MY Avalon HV [08/2021 -        ]; HYBRID / BATTERY CONTROL: HYBRID VEHICLE CONTROL ECU: REMOVAL

OK

5.

INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (OUTPUT VOLTAGE)

*a

Component with harness connected

(Instrument Panel Junction Block Assembly)

(a) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

4H-10 - Body ground

Power switch off, reverse (R) not selected

Below 1 V

4H-10 - Body ground

Power switch on (IG), reverse (R) selected

11 to 14 V

OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY 2019 - 2021 MY Avalon Avalon HV [04/2018 - 08/2021]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL 2022 MY Avalon Avalon HV [08/2021 -        ]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL