Last Modified: 08-21-2023 |
6.11:8.1.0 |
Doc ID: RM100000001PY3X |
Model Year Start: 2021 |
Model: Avalon HV |
Prod Date Range: [08/2020 -
] |
Title: TELEMATICS: TELEMATICS SYSTEM: Remote Engine Starter does not Operate; 2021 - 2022 MY Avalon Avalon HV [08/2020 - ] |
Remote Engine Starter does not Operate
|
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
Before replacing the DCM (telematics transceiver), refer to Registration.
for HV Model: Click here
for Gasoline Model: Click here
PROCEDURE
1.
|
CHECK SMART KEY SYSTEM (for Start Function)
|
(a) Check that the engine or hybrid system can be started by pressing the ignition switch.
Result
|
Proceed to
|
Engine or hybrid system can be started.
|
A
|
Engine or hybrid system cannot be started.
|
B
|
B |
|
GO TO SMART KEY SYSTEM (for Start Function)
for HV Model: Click here
for Gasoline Model: Click here
|
A
|
|
|
HINT:
If registration is not performed after replacing any of the following parts, the remote engine start and stop will not be available.
-
Certification ECU (smart key ECU assembly)
-
DCM (telematics transceiver)
(a) Perform remote engine start and stop registration.
for HV Model: Click here
for Gasoline Model: Click here
(b) Check if the problem symptom recurs.
Result
|
Proceed to
|
System does not return to normal.
|
A
|
System returns to normal.
|
B
|
B |
|
END
|
A
|
|
|
(a) Clear the DTCs.
Body Electrical > Smart Key > Clear DTCs
(b) Check for DTCs.
Body Electrical > Smart Key > Trouble Codes
Result
|
Proceed to
|
DTC B2285 is not output.
|
A
|
DTC B2285 is output.
|
B
|
B |
|
GO TO DTC B2285
for HV Model: Click here
for Gasoline Model: Click here
|
A
|
|
|
4.
|
CHECK DCM (TELEMATICS TRANSCEIVER)
|
(a) Disconnect the G124 DCM (telematics transceiver) connector.
|
|
*a
|
Front view of harness connector
(to DCM (Telematics Transceiver))
|
|
|
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
|
Condition
|
Specified Condition
|
G124-30 (SLPD) - Body ground
|
Steering locked
|
11 to 14 V
|
Steering unlocked
|
Below 1.5 V
|
HINT:
The steering locks when any door is opened with the shift lever in P and the ignition switch off. The steering unlocks when the ignition switch is turned to ON.
NG
|
|
|
5.
|
CHECK HARNESS AND CONNECTOR (DCM (TELEMATICS TRANSCEIVER) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
|
(a) Disconnect the G124 DCM (telematics transceiver) connector.
(b) Disconnect the G40 certification ECU (smart key ECU assembly) connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
G124-30 (SLPD) - G40-14 (SLP)
|
Always
|
Below 1 Ω
|
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
|