Last Modified: 08-21-2023 6.11:8.1.0 Doc ID: RM100000001PX3B
Model Year Start: 2021 Model: Avalon Prod Date Range: [08/2020 -           ]
Title: A25A-FKS (ENGINE CONTROL): CAMSHAFT TIMING CONTROL MOTOR: REMOVAL; 2021 - 2022 MY Avalon [08/2020 -        ]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during cam timing control motor with EDU assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link
*1: When performing learning using the Techstream.

Click here 2019 - 2022 MY Avalon [04/2018 -        ]; PARK ASSIST / MONITORING: INTELLIGENT CLEARANCE SONAR SYSTEM (for Gasoline Model): CALIBRATION

Battery terminal is disconnected/reconnected

Perform steering sensor zero point calibration

Lane Departure Alert System (w/ Steering Control)

2019 - 2021 MY Avalon [04/2018 - 08/2021]; PRE-COLLISION: PRE-COLLISION SYSTEM (for Gasoline Model): INITIALIZATION 2022 MY Avalon Avalon HV [08/2021 -        ]; PRE-COLLISION: PRE-COLLISION SYSTEM: INITIALIZATION

Pre-collision System

Intelligent Clearance Sonar System*1

Lighting System (for Gasoline Model with Cornering Light)

Memorize steering angle neutral point

Parking Assist Monitor System

2019 - 2022 MY Avalon [04/2018 -        ]; PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM (for Gasoline Model): INITIALIZATION

Panoramic View Monitor System

2019 - 2022 MY Avalon [04/2018 -        ]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM (for Gasoline Model): INITIALIZATION

  • Replacement of cam timing control motor with EDU assembly
  • Removal and installation of a cam timing control motor with EDU assembly

Inspection after repair
  • Poor idle, etc.
  • Engine start function, etc.

2021 - 2022 MY Avalon [08/2020 -        ]; A25A-FKS (ENGINE CONTROL): SFI SYSTEM: INITIALIZATION

NOTICE:

  • After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here 2019 - 2022 MY Avalon Avalon HV [04/2018 -        ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION

  • This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

    Click here 2019 - 2022 MY Avalon Avalon HV [04/2018 -        ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION

PROCEDURE

1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Click here 2021 - 2022 MY Avalon [08/2020 -        ]; MAINTENANCE: A25A-FKS BATTERY: REMOVAL+

2. REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

Click here 2021 - 2022 MY Avalon [08/2020 -        ]; A25A-FKS (ENGINE MECHANICAL): ENGINE ASSEMBLY: REMOVAL+

3. REMOVE NO. 1 BRAKE TUBE CLAMP BRACKET

Click here 2021 - 2022 MY Avalon [08/2020 -        ]; A25A-FKS (ENGINE CONTROL): CAMSHAFT OIL CONTROL SOLENOID: REMOVAL+

4. REMOVE NO. 2 ENGINE COVER

Click here 2021 - 2022 MY Avalon [08/2020 -        ]; A25A-FKS (ENGINE MECHANICAL): ENGINE UNIT: REMOVAL+

5. REMOVE CAM TIMING CONTROL MOTOR WITH EDU ASSEMBLY

(a) Disconnect the cam timing control motor with EDU assembly connector.

(b) Remove the 3 bolts and cam timing control motor with EDU assembly from the No. 2 timing gear cover assembly.

NOTICE:

If the cam timing control motor with EDU assembly has been struck or dropped, replace it.

6. REMOVE CAM TIMING CONTROL MOTOR O-RING

(a) Remove the cam timing control motor O-ring from the No. 2 timing gear cover assembly.