Last Modified: 08-21-2023 6.11:8.1.0 Doc ID: RM100000001C2LV
Model Year Start: 2019 Model: Avalon HV Prod Date Range: [04/2018 -           ]
Title: PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM (for HV Model): DATA LIST / ACTIVE TEST; 2019 - 2022 MY Avalon HV [04/2018 -        ]

DATA LIST / ACTIVE TEST

DATA LIST

HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

(a) Connect the Techstream to the DLC3.

(b) Turn the power switch on (READY).

(c) Turn the Techstream on.

(d) Enter the following menus: Chassis / Panoramic View Monitor / Data List.

(e) Read the Data List according to the display on the Techstream.

Chassis > Panoramic View Monitor > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

HV/ENG Data Check

Status of the HV/ENG data check

Normal/Abnormal

Normal: Parking assist ECU is normal

Abnormal: Parking assist ECU is abnormal

-

Display Drawing Function (Intuitive P/A Forward Detection) With or Without Comparing

Rear television camera assembly drawing function (clearance sonar forward detection) with or without comparing

Match or Mismatch

Match: Rear television camera assembly normal

Mismatch: Rear television camera assembly abnormal

-

Main CPU Forced Termination Detection Record

A history item indicating that the main CPU did not enter standby status within 15 seconds of turning the power switch off and a forced end was applied

No/Yes

No: Parking assist ECU is normal

Yes: Parking assist ECU is abnormal

-

Main CPU Abnormal Response Record

A history item indicating that the main CPU became unresponsive in normal status

No/Yes

No: Parking assist ECU is normal

Yes: Parking assist ECU is abnormal

-

Main CPU Abnormal Reset Record

A history item indicating that the main CPU was reset, although the power switch was not turned off in normal status

No/Yes

No: Parking assist ECU is normal

Yes: Parking assist ECU is abnormal

-

Image Processing IC Written Protect Record

A history item indicating that the image processing IC memory was write protected

No/Yes

No: Parking assist ECU is normal

Yes: Parking assist ECU is abnormal

-

Image Processing IC Initialized Malfunction Record

A history item indicating that the image processing IC memory was not initialized

No/Yes

No: Parking assist ECU is normal

Yes: Parking assist ECU is abnormal

-

Main EEPROM Access Status

Main EEPROM access status

Normal/Abnormal

Normal: Parking assist ECU is normal

Abnormal: Parking assist ECU is abnormal

-

Sub EEPROM Access Status

Sub-EEPROM access status

Normal/Abnormal

Normal: Parking assist ECU is normal

Abnormal: Parking assist ECU is abnormal

-

System Power Supply Voltage Malfunction Record

A history item indicating an abnormally generated-voltage value from the system power source

No/Yes

No: Parking assist ECU is normal

Yes: Parking assist ECU is abnormal

-

Main CPU Starting Malfunction Record

A history item indicating that the main CPU did not start

No/Yes

No: Parking assist ECU is normal

Yes: Parking assist ECU is abnormal

-

CAN CPU Boot Malfunction Record

A history item indicating that the CPU controlling the input and output of the information obtained via CAN communication did not start and the information could not be retrieved

No/Yes

No: Parking assist ECU is normal

Yes: Parking assist ECU is abnormal

-

Visual Display Line Status

Displays the status of the video signals displayed on the multi-display

ON/OFF

OK: GVIF cable is normal

NG: GVIF cable is abnormal

-

Wheel Speed Sensor (4wheel)

Reception state of the vehicle speed signal from the skid control ECU

Valid/Invalid

Valid: Speed signal received

Invalid: Speed signal not received

-

Bus-off Continuation Detection Record

A history item indicating that the bus off condition was detected

No/Yes

No: Parking assist ECU is normal

Yes: Parking assist ECU is abnormal

-

Continuous Bus Off

Continuous bus off status (Global)

Not Detected/Detected

Not detected: Communication condition available

Detected: Communication condition not available

-

Sending CAN Message

Communication condition from parking assist ECU (Global)

OK/NG

OK: Communication condition available

NG: Communication condition not available

-

Shift R Position

Reverse signal

ON/OFF

OFF: Shift lever in any position except R

ON: Shift lever in R

-

Camera Changing SW Signal Status

Signal status at the BLSW terminal (switch camera signal)

ON/OFF

ON: Panoramic view monitor switch on

OFF: Panoramic view monitor switch off

-

Back Camera Availability Consistency

Status of ECU stored in television camera assembly

OK/NG

OK: Normal

NG: Television camera assembly or parking assist ECU is abnormal

-

Side Camera LH Availability Consistency

Status of ECU stored in side television camera assembly LH

OK/NG

OK: Normal

NG: Side television camera assembly LH or parking assist ECU is abnormal

-

Front Camera Availability Consistency

Status of ECU stored in front television camera assembly

OK/NG

OK: Normal

NG: Front television camera assembly or parking assist ECU is abnormal

-

Side Camera RH Availability Consistency

Status of ECU stored side television camera assembly RH

OK/NG

OK: Normal

NG: Side television camera assembly RH or parking assist ECU is abnormal

-

Image Adjustment Status

Status of the image adjustment status

Incomplete/Processing/Complete

Incomplete: Image adjustment incomplete

Processing: Image adjustment in processing

Complete: Image adjustment completed

-

Number of DTC

Number of DTCs (past and present)

Min: 0, Max: 255

Changes according to the number of DTCs output

-

Chassis > Parking Assist Camera > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Wheel Speed Sensor (4wheel)

Effectivity of speed signal from speed signal sensor

OK or NG

OK: Speed signal is effective

NG: Speed signal is not effective

-

Video Output Status

Output condition of video signal

OK or NG

OK: Output condition of video signal is normal

NG: Output condition of video signal is abnormal

-

HV/ENG Data Check

Verification of the HV/ENG data

OK or NG

OK: Data verification normal

NG: Data verification abnormal

-

Circumference Monitoring System Type Check

Verification of television camera assembly signal

OK or NG

OK: Television camera assembly normal

NG: Television camera assembly abnormal

-

EEPROM Status (Initial read)

Television camera assembly information

OK or NG

OK: Television camera assembly normal

NG: Television camera assembly abnormal

-

CPU Communication Status

Television camera assembly information

OK or NG

OK: Television camera assembly normal

NG: Television camera assembly abnormal

-

Number of DTC

Number of stored DTCs

min.: 0, max.: 255

Number of DTCs will be displayed

-

Current Key Cycle

Cumulative number of times the power switch was turned on (IG)

Min.: 0, Max.: 65535 time

Cumulative number of times the power switch was turned on (IG) will be displayed

-

Current Key Cycle Elapsed Time

Time elapsed since the power switch was turned on (IG)

Min.: 0, Max.: 1677721.5 s

Time elapsed since the power switch was turned on (IG) will be displayed

-