| Last Modified: 08-21-2023 | 6.11:8.1.0 | Doc ID: RM100000001BKCP |
| Model Year Start: 2019 | Model: Avalon | Prod Date Range: [04/2018 - ] |
| Title: SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (for Gasoline Model): B1865-B1868; Short in Knee Airbag (P Side) Squib Circuit; 2019 - 2022 MY Avalon [04/2018 - ] | ||
|
DTC |
B1865 |
Short in Knee Airbag (P Side) Squib Circuit |
|
DTC |
B1866 |
Open in Knee Airbag (P Side) Squib Circuit |
|
DTC |
B1867 |
Short in Knee Airbag (P Side) Squib Circuit (to Ground) |
|
DTC |
B1868 |
Short in Knee Airbag (P Side) Squib Circuit (to +B) |
DESCRIPTION
The front passenger side knee airbag squib circuit consists of the airbag ECU assembly and lower No. 2 instrument panel airbag assembly.
The airbag ECU assembly uses this circuit to deploy the airbag when deployment conditions are met.
These DTCs are stored when a malfunction is detected in the front passenger side knee airbag squib circuit.
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
Warning Indicate |
Test Mode / Check Mode |
|---|---|---|---|---|---|
|
B1865 |
Short in Knee Airbag (P Side) Squib Circuit |
|
|
Comes on |
Applies to check mode |
|
B1866 |
Open in Knee Airbag (P Side) Squib Circuit |
|
|
Comes on |
Applies to check mode |
|
B1867 |
Short in Knee Airbag (P Side) Squib Circuit (to Ground) |
|
|
Comes on |
Applies to check mode |
|
B1868 |
Short in Knee Airbag (P Side) Squib Circuit (to +B) |
|
|
Comes on |
Applies to check mode |
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click here
![2019 - 2022 MY Avalon Avalon HV [04/2018 - ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION](/t3Portal/stylegraphics/info.gif)
HINT:
-
Perform the simulation method by selecting check mode (Signal Check) using the Techstream.
Click here
-
After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road.
Click here
PROCEDURE
|
1. |
CHECK CONNECTORS |
|
(a) Turn the engine switch off. |
|
(b) Disconnect the cable from the negative (-) battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
(c) Check that the connectors are properly connected to the lower No. 2 instrument panel airbag assembly and airbag ECU assembly.
OK:
The connectors are properly connected.
HINT:
If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.
(d) Disconnect the connectors from the lower No. 2 instrument panel airbag assembly and airbag ECU assembly.
(e) Check that the terminals of the connectors are not deformed or damaged.
OK:
The terminals are not deformed or damaged.
(f) Check that the instrument panel wire connector (on the lower No. 2 instrument panel airbag assembly side) is not loose, deformed or damaged.
OK:
The airbag connector locking button is not disengaged, and the claw of the lock is not deformed or damaged.
(g) Check that the short springs of the activation prevention mechanism of the instrument panel wire connector are not deformed or damaged.
OK:
The short springs are not deformed or damaged.
| NG |
|
REPLACE INSTRUMENT PANEL WIRE |
|
|
2. |
CHECK LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY |
|
(a) Connect the connector to the airbag ECU assembly. |
|
(b) Connect SST (resistance 2.1 Ω) to connector C.
CAUTION:
Never connect a tester to the lower No. 2 instrument panel airbag assembly for measurement, as this may lead to a serious injury due to airbag deployment.
NOTICE:
- Do not forcibly insert SST into the terminals of the connector when connecting it.
- Insert SST straight into the terminals of the connector.
SST: 09843-18061
(c) Connect the cable to the negative (-) battery terminal.
(d) Turn the engine switch on (IG), and wait for at least 60 seconds.
(e) Clear the DTCs stored in memory.
Body Electrical > SRS Airbag > Clear DTCs
(f) Turn the engine switch off.
(g) Turn the engine switch on (IG), and wait for at least 60 seconds.
(h) Check for DTCs.
Body Electrical > SRS Airbag > Trouble Codes
OK:
DTC B1865, B1866, B1867 or B1868 is not output.
HINT:
Codes other than DTCs B1865, B1866, B1867 and B1868 may be output at this time, but they are not related to this check.
(i) Turn the engine switch off.
(j) Disconnect the cable from the negative (-) battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
(k) Disconnect SST from connector C.
| OK |
|
REPLACE LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY
|
|
|
3. |
CHECK INSTRUMENT PANEL WIRE |
|
(a) Disconnect the instrument panel wire from the airbag ECU assembly. |
|
(b) Check for a short to B+ in the circuit.
(1) Connect the cable to the negative (-) battery terminal.
(2) Turn the engine switch on (IG).
(3) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
G56-1 (PK+) - Body ground |
Engine switch on (IG) |
Below 1 V |
|
G56-2 (PK-) - Body ground |
Engine switch on (IG) |
Below 1 V |
(4) Turn the engine switch off.
(5) Disconnect the cable from the negative (-) battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
(c) Check for an open in the circuit.
(1) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
G56-1 (PK+) - G56-2 (PK-) |
Always |
Below 1 Ω |
(d) Check for a short to ground in the circuit.
(1) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
G56-1 (PK+) - Body ground |
Always |
1 MΩ or higher |
|
G56-2 (PK-) - Body ground |
Always |
1 MΩ or higher |
(e) Check for a short in the circuit.
(1) Release the activation prevention mechanism built into connector B.
Click here
(2) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
G56-1 (PK+) - G56-2 (PK-) |
Always |
1 MΩ or higher |
(3) Restore the released activation prevention mechanism of connector B to the original condition.
| NG |
|
REPLACE INSTRUMENT PANEL WIRE |
|
|
4. |
CHECK DTC |
|
(a) Connect the connectors to the lower No. 2 instrument panel airbag assembly and airbag ECU assembly. |
|
(b) Connect the cable to the negative (-) battery terminal.
(c) Turn the engine switch on (IG), and wait for at least 60 seconds.
(d) Clear the DTCs stored in memory.
Body Electrical > SRS Airbag > Clear DTCs
(e) Turn the engine switch off.
(f) Turn the engine switch on (IG), and wait for at least 60 seconds.
(g) Check for DTCs.
Body Electrical > SRS Airbag > Trouble Codes
OK:
DTC B1865, B1866, B1867 or B1868 is not output.
HINT:
Codes other than DTCs B1865, B1866, B1867 and B1868 may be output at this time, but they are not related to this check.
| OK |
|
| NG |
|
REPLACE AIRBAG ECU ASSEMBLY
|
|
|