| Last Modified: 08-21-2023 | 6.11:8.1.0 | Doc ID: RM100000001B4T8 |
| Model Year Start: 2019 | Model: Avalon HV | Prod Date Range: [04/2018 - 08/2020] |
| Title: CELLULAR COMMUNICATION: DCM(TELEMATICS TRANSCEIVER): REMOVAL; 2019 - 2020 MY Avalon Avalon HV [04/2018 - 08/2020] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during DCM (telematics transceiver) removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function When Necessary Procedures are not Performed |
Link |
|---|---|---|---|
| *: for Toyota Entune Remote Connect Compatible Type | |||
|
Replacement of DCM (telematics transceiver) |
DCM activation |
Safety Connect System |
|
|
Replacement of DCM (telematics transceiver)* |
Code registration (Smart key System (for Start Function)) |
Smart Key System (for Start Function) |
|
Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function When Necessary Procedures are not Performed |
Link |
|---|---|---|---|
| *: for Toyota Entune Remote Connect Compatible Type | |||
|
Replacement of DCM (telematics transceiver) |
DCM activation |
Safety Connect System |
|
|
Replacement of DCM (telematics transceiver)* |
Code registration (Smart key System (for Start Function)) |
Smart Key System (for Start Function) |
|
PROCEDURE
1. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL LH
Click here
![2019 - 2020 MY Avalon Avalon HV [04/2018 - 08/2020]; INTERIOR PANELS / TRIM: FRONT CONSOLE BOX: REMOVAL+](/t3Portal/stylegraphics/info.gif)
2. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL RH
Click here
3. REMOVE FRONT CONSOLE UPPER PANEL GARNISH
Click here
4. REMOVE CONSOLE BOX POCKET SUB-ASSEMBLY
Click here
5. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
Click here
6. REMOVE CENTER NO. 1 INSTRUMENT CLUSTER FINISH PANEL
Click here
7. REMOVE CENTER NO. 2 INSTRUMENT CLUSTER FINISH PANEL
Click here
8. REMOVE RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET
Click here
9. REMOVE NO. 2 HEATER TO REGISTER DUCT SUB-ASSEMBLY
Click here
10. REMOVE DCM (TELEMATICS TRANSCEIVER) WITH BRACKET
(a) w/o Navigation System:
|
(1) Disconnect the connector. |
|
(2) Remove the 2 nuts and pull the DCM (telematics transceiver) with bracket as shown in the illustration.
|
Remove in this Direction |
(3) Disconnect each connector and remove the DCM (telematics transceiver) with bracket.
(b) w/ Navigation System:
|
(1) Disconnect the 2 connectors. |
|
(2) Remove the 2 nuts and pull the DCM (telematics transceiver) with bracket as shown in the illustration.
|
|
Remove in this Direction |
(3) Disconnect each connector and remove the DCM (telematics transceiver) with bracket.
11. REMOVE TELEPHONE AND GPS ANTENNA CORD
Click here
12. REMOVE NO. 2 TELEPHONE BRACKET
(a) w/o Navigation System:
|
(1) Disengage the wiring harness clamp. |
|
|
(2) Remove the screw and disengage the 2 guides to remove the No. 2 telephone bracket. |
|
(b) w/ Navigation System:
|
(1) Disengage the clamp. |
|
|
(2) Disengage the wiring harness clamp. |
|
|
(3) Remove the 3 screws and disengage the 3 guides to remove the No. 2 telephone bracket. |
|
13. REMOVE NO. 1 TELEPHONE BRACKET
(a) w/o Navigation System:
|
(1) Remove the screw and disengage the 2 guides to remove the No. 1 telephone bracket. |
|
(b) w/ Navigation System:
|
(1) Remove the 3 screws and disengage the 3 guides to remove the No. 1 telephone bracket. |
|
14. REMOVE NAVIGATION ECU WITH ANTENNA CORD (w/ Navigation System)
15. REMOVE DCM (TELEMATICS TRANSCEIVER)
|
|