Last Modified: 08-21-2023 6.11:8.1.0 Doc ID: RM100000001B4CW
Model Year Start: 2019 Model: Avalon HV Prod Date Range: [04/2018 -           ]
Title: A25A-FXS (ENGINE CONTROL): SFI SYSTEM: P064A49; Fuel Pump Control Module Internal Electronic Failure; 2019 - 2022 MY Avalon HV [04/2018 -        ]

DTC

P064A49

Fuel Pump Control Module Internal Electronic Failure

MONITOR DESCRIPTION

The fuel pump control ECU has a self-diagnosis function. If there is an internal malfunction, the fuel pump control ECU sends a malfunction signal to the ECM via the FPC drive circuit.

Based on the signal, the ECM judges that there is a malfunction in the fuel pump control ECU stores a DTC.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Memory

Note

P064A49

Fuel Pump Control Module Internal Electronic Failure

When the fuel pump control ECU operation duty ratio is 3 to 65%, there is an internal malfunction in the fuel pump control ECU for 3 seconds or more (2 trip detection logic).

Fuel pump control ECU

Comes on

DTC stored

SAE Code: P064A

MONITOR STRATEGY

Related DTCs

P064A: Fuel pump control module range check

Required Sensors/Components (Main)

Fuel pump control ECU

Required Sensors/Components (Related)

-

Frequency of Operation

Continuous

Duration

3 seconds

MIL Operation

2 driving cycles

Sequence of Operation

None

TYPICAL ENABLING CONDITIONS

Monitor runs whenever the following DTCs are not stored

None

All of the following conditions are met

-

Output duty cycle

3 to 65%

Auxiliary battery voltage

10.5 V or higher

Power switch

On (IG)

TYPICAL MALFUNCTION THRESHOLDS

Internal malfunction from fuel pump control module

Received

CONFIRMATION DRIVING PATTERN

HINT:

  • After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

    Click here 2019 - 2022 MY Avalon HV [04/2018 -        ]; A25A-FXS (ENGINE CONTROL): SFI SYSTEM: DTC CHECK / CLEAR

  • When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.

    Click here 2019 - 2022 MY Avalon HV [04/2018 -        ]; A25A-FXS (ENGINE CONTROL): SFI SYSTEM: DTC CHECK / CLEAR

  1. Connect the Techstream to the DLC3.
  2. Turn the power switch on (IG).
  3. Turn the Techstream on.
  4. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  5. Turn the power switch off and wait for at least 30 seconds.
  6. Turn the power switch on (IG).
  7. Turn the Techstream on.
  8. Put the engine in Inspection Mode (Maintenance Mode).

    Click here 2019 - 2022 MY Avalon Avalon HV [04/2018 -        ]; INTRODUCTION: REPAIR INSTRUCTION: INSPECTION MODE PROCEDURE

  9. Start the engine and wait 10 seconds or more [A].
  10. Enter the following menus: Powertrain / Engine / Trouble Codes [B].
  11. Read the pending DTCs.

    HINT:

    • If a pending DTC is output, the system is malfunctioning.
    • If a pending DTC is not output, perform the following procedure.
  12. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
  13. Input the DTC: P064A49.
  14. Check the DTC judgment result.

    Techstream Display

    Description

    NORMAL

    • DTC judgment completed
    • System normal

    ABNORMAL

    • DTC judgment completed
    • System abnormal

    INCOMPLETE

    • DTC judgment not completed
    • Perform driving pattern after confirming DTC enabling conditions

    HINT:

    • If the judgment result is NORMAL, the system is normal.
    • If the judgment result is ABNORMAL, the system is malfunctioning.
    • If the judgment result is INCOMPLETE, run the engine at an engine speed of 2500 rpm or more for 10 seconds or more and check the DTC judgment result again.
    • [A] to [B]: Normal judgment procedure.

      The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.

    • When clearing the permanent DTCs, do not disconnect the cable from the auxiliary battery terminal or attempt to clear the DTCs during this procedure, as doing so will clear the universal trip and normal judgment histories.

CAUTION / NOTICE / HINT

NOTICE:

  • Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the Freeze Frame Data and Vehicle Control History can be useful for troubleshooting.

    Click here 2019 - 2020 MY Avalon HV [04/2018 - 08/2020]; HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY): VEHICLE CONTROL HISTORY 2021 - 2022 MY Avalon HV [08/2020 -        ]; HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY): VEHICLE CONTROL HISTORY

    (Select Powertrain in Health Check and then check the time stamp data.)

    Click here 2019 - 2022 MY Avalon HV [04/2018 -        ]; A25A-FXS (ENGINE CONTROL): SFI SYSTEM: DTC CHECK / CLEAR

  • If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

    Click here 2019 - 2020 MY Avalon HV [04/2018 - 08/2020]; HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY): VEHICLE CONTROL HISTORY 2021 - 2022 MY Avalon HV [08/2020 -        ]; HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY): VEHICLE CONTROL HISTORY

HINT:

Read Freeze Frame Data using the Techstream. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE

1.

CLEAR DTC

(a) Connect the Techstream to the DLC3.

(b) Turn the power switch on (IG).

(c) Turn the Techstream on.

(d) Clear the DTCs.

Powertrain > Engine > Clear DTCs

(e) Turn the power switch off and wait for at least 30 seconds.

NEXT

2.

CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P064A49)

(a) Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

(b) Enter the following menus: Powertrain / Engine / Trouble Codes.

(c) Read the DTCs.

Powertrain > Engine > Trouble Codes

Result

Proceed to

DTC P064A49 is output

A

DTC P064A49 and other DTCs are output

B

A

REPLACE FUEL PUMP CONTROL ECU 2019 - 2021 MY Avalon HV [04/2018 - 08/2021]; A25A-FXS (FUEL): FUEL PUMP ECU: REMOVAL 2022 MY Avalon HV [08/2021 -        ]; A25A-FXS (FUEL): FUEL PUMP ECU: REMOVAL

B

GO TO DTC CHART 2019 MY Avalon HV [04/2018 - 08/2019]; A25A-FXS (ENGINE CONTROL): SFI SYSTEM: DIAGNOSTIC TROUBLE CODE CHART 2020 MY Avalon HV [08/2019 - 08/2020]; A25A-FXS (ENGINE CONTROL): SFI SYSTEM: DIAGNOSTIC TROUBLE CODE CHART 2021 MY Avalon HV [08/2020 - 08/2021]; A25A-FXS (ENGINE CONTROL): SFI SYSTEM: DIAGNOSTIC TROUBLE CODE CHART 2022 MY Avalon HV [08/2021 -        ]; A25A-FXS (ENGINE CONTROL): SFI SYSTEM: DIAGNOSTIC TROUBLE CODE CHART