Last Modified: 08-21-2023 6.11:8.1.0 Doc ID: RM100000001B2OI
Model Year Start: 2019 Model: Avalon HV Prod Date Range: [04/2018 -           ]
Title: THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, HV Model): B27A5; Open in Front Floor Electrical Key Oscillator Circuit; 2019 - 2022 MY Avalon HV [04/2018 -        ]

DTC

B27A5

Open in Front Floor Electrical Key Oscillator Circuit

DESCRIPTION

The certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the No. 1 indoor electrical key antenna assembly (front floor). For the No. 1 indoor electrical key antenna assembly (front floor) to detect when the electrical key transmitter sub-assembly is in the cabin, the signal from the certification ECU (smart key ECU assembly) requesting a response from the electrical key transmitter sub-assembly is transmitted inside the vehicle. DTC B27A5 is stored by the certification ECU (smart key ECU assembly) when an open is detected between the certification ECU (smart key ECU assembly) and No. 1 indoor electrical key antenna assembly (front floor) (between terminals CLG5 and ANTE5, or terminals CG5B and CLGB).

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

Note

B27A5

Open in Front Floor Electrical Key Oscillator Circuit

An open is detected in the circuit between the certification ECU (smart key ECU assembly) and No. 1 indoor electrical key antenna assembly (front floor) (CLG5 - ANTE5, CG5B - CLGB) (1 trip detection logic*).

  • Certification ECU (smart key ECU assembly)
  • No. 1 indoor electrical key antenna assembly (front floor)
  • Wire harness or connector

DTC Output Confirmation Operation:

  • Any time
  • *: Only output while a malfunction is present.

Vehicle Condition and Fail-safe Operation when Malfunction Detected

Vehicle Condition when Malfunction Detected

Fail-safe Operation when Malfunction Detected

When electrical key transmitter sub-assembly is in front seat area:

  • Power source mode does not change when power switch pressed
  • Electrical key transmitter sub-assembly locked inside vehicle

-

Related Data List and Active Test

DTC No.

Data List and Active Test

B27A5

Key diagnostic mode can be used to perform troubleshooting

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

  • When using the Techstream with the power switch off, connect the Techstream to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Smart Key. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.
  • The smart key system (for Start Function, HV Model) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart key system (for Start Function, HV Model) after confirming that the communication systems are functioning properly.

    Click here 2019 - 2022 MY Avalon HV [04/2018 -        ]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, HV Model): HOW TO PROCEED WITH TROUBLESHOOTING

  • Before replacing the certification ECU (smart key ECU assembly), refer to Registration.

    Click here 2019 - 2020 MY Avalon HV [04/2018 - 08/2020]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, HV Model): REGISTRATION 2021 - 2022 MY Avalon HV [08/2020 -        ]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, HV Model): REGISTRATION

  • After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

PROCEDURE

1.

CHECK CONNECTOR CONNECTION

(a) Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and No. 1 indoor electrical key antenna assembly (front floor).

OK:

Connectors are properly connected.

NG

CONNECT CONNECTORS PROPERLY

OK

2.

CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR))

(a) Disconnect the G40 certification ECU (smart key ECU assembly) connector.

(b) Disconnect the G42 No. 1 indoor electrical key antenna assembly (front floor) connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

G40-8 (CLG5) - G42-1 (ANTE5)

Always

Below 1 Ω

G40-9 (CG5B) - G42-3 (CLGB)

Always

Below 1 Ω

(d) Reconnect the G40 certification ECU (smart key ECU assembly) connector.

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

3.

CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR))

*a

Component with harness connected

(Certification ECU (Smart Key ECU Assembly))

*b

Waveform

*c

For 30 seconds after any door closed

*d

After 30 seconds or more have elapsed since any door closed

(a) Using an oscilloscope, check the waveform.

OK:

Tester Connection

Condition

Tool Setting

Specified Condition

G40-8 (CLG5) - G40-18 (E)

Procedure:

  1. Power switch off
  2. Electrical key transmitter sub-assembly not inside vehicle
  3. Within 30 seconds of closing any door

2 V/DIV., 500 ms/DIV.

Pulse generation

(See waveform)

G40-9 (CG5B) - G40-18 (E)

Procedure:

  1. Power switch off
  2. Electrical key transmitter sub-assembly not inside vehicle
  3. Within 30 seconds of closing any door

2 V/DIV., 500 ms/DIV.

Pulse generation

(See waveform)

OK

REPLACE NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) 2019 - 2021 MY Avalon Avalon HV [04/2018 - 08/2021]; THEFT DETERRENT / KEYLESS ENTRY: CERTIFICATION ECU: REMOVAL 2022 MY Avalon Avalon HV [08/2021 -        ]; THEFT DETERRENT / KEYLESS ENTRY: CERTIFICATION ECU: REMOVAL