Last Modified: 08-21-2023 6.11:8.1.0 Doc ID: RM100000001AYPP
Model Year Start: 2019 Model: Avalon HV Prod Date Range: [04/2018 -           ]
Title: BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model): Brake Hold Operated Indicator Light Circuit; 2019 - 2022 MY Avalon HV [04/2018 -        ]

Brake Hold Operated Indicator Light Circuit

DESCRIPTION

The brake hold operated indicator light illuminates when the brake hold system is operating (vehicle stopped via brake fluid pressure hold) and turns off when the brake hold system operation is finished (brake fluid pressure decreases).

The brake hold system may not operate depending on vehicle conditions even when the system is in standby mode and the brake hold standby indicator light is illuminated.

If there is a system malfunction that causes brake hold control to be prohibited, when the vehicle is under the following conditions and the brake hold switch (electric parking brake switch assembly) is turned on, the brake hold operated indicator light blinks.

  • Vehicle Conditions:
    1. The driver side door is closed.
    2. The driver side seat belt is fastened.

HINT:

  • When the power switch is turned off during brake hold operation, control stops.
  • If brake hold control does not operate even when the vehicle stops, depress on the brake pedal again firmly to stop the vehicle.

    If brake hold control still does not operate, confirm the conditions for brake hold control to operate.

CAUTION / NOTICE / HINT

NOTICE:

After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click here 2019 - 2021 MY Avalon HV [04/2018 - 08/2021]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model): INITIALIZATION 2022 MY Avalon HV [08/2021 -        ]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model): INITIALIZATION

PROCEDURE

1.

PRE-CHECK

(a) Check that the brake hold standby indicator light operates normally.

Click here 2019 - 2022 MY Avalon HV [04/2018 -        ]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model): Brake Hold Standby Indicator Light Circuit

(b) If the brake hold operated indicator light does not illuminate although the brake hold standby indicator light is illuminated, check that the following brake hold operation (maintaining brake fluid pressure) conditions are met.

  1. System is in operation standby state (brake hold standby indicator light is illuminated).
  2. Shift position is not P or R.
  3. Driver is depressing brake pedal and vehicle is fully stopped.
  4. Driver is not depressing accelerator pedal.
  5. Vehicle is not on steep decline.

HINT:

If a malfunction occurs in one of the following systems, the brake hold operated indicator light will blink. If this occurs, perform troubleshooting on the malfunctioning system.

  • Brake system
  • Electric parking brake system
  • Hybrid control system
NEXT

2.

INSPECT COMBINATION METER ASSEMBLY

(a) Turn the power switch off.

(b) Perform the Active Test of the combination meter assembly (meter CPU) using the Techstream.

Click here 2019 - 2021 MY Avalon HV [04/2018 - 08/2021]; METER / GAUGE / DISPLAY: METER / GAUGE SYSTEM (for HV Model): DATA LIST / ACTIVE TEST 2022 MY Avalon HV [08/2021 -        ]; METER / GAUGE / DISPLAY: METER / GAUGE SYSTEM (for HV Model): DATA LIST / ACTIVE TEST

Body Electrical > Combination Meter > Active Test

Tester Display

Hold Indicator

(c) Check the combination meter assembly.

OK:

The brake hold operated indicator light turns on or off in accordance with Techstream operation.

NG

INSPECT METER / GAUGE SYSTEM

OK

3.

PERFORM ACTIVE TEST USING TECHSTREAM (BRAKE HOLD OPERATED INDICATOR LIGHT)

(a) Select the Active Test on the Techstream.

Click here 2019 - 2022 MY Avalon HV [04/2018 -        ]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model): DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRAC > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

BH Operated Light

Brake hold operated indicator light

Indicator light ON/OFF

Observe combination meter assembly

Chassis > ABS/VSC/TRAC > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

BH Operated Light

Brake hold operated indicator light

ON or OFF

ON: Indicator light on

OFF: Indicator light off

-

Chassis > ABS/VSC/TRAC > Active Test

Active Test Display

BH Operated Light

Data List Display

BH Operated Light

(b) Check the operating condition of the brake hold operated indicator light when operating it using the Techstream.

Result

Proceed to

Brake hold operated indicator light in the Data List does not change using the Active Test.

A

Brake hold operated indicator light in the Data List turns ON/OFF using the Active Test.

B
A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY 2019 - 2021 MY Avalon HV [04/2018 - 08/2021]; BRAKE SYSTEM (OTHER): BRAKE BOOSTER (for HV Model): REMOVAL 2022 MY Avalon HV [08/2021 -        ]; BRAKE SYSTEM (OTHER): BRAKE BOOSTER (for HV Model): REMOVAL

B

USE SIMULATION METHOD TO CHECK