INSTALLATION

PROCEDURE

1. TEMPORARILY INSTALL AIR CONDITIONER UNIT ASSEMBLY

Click here

2. INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONER UNIT ASSEMBLY

(a) Connect each connector.

Install in this Direction

-

-

(b) Engage each clamp.

(c) Temporarily install the instrument panel reinforcement assembly with air conditioner unit assembly as shown in the illustration.

(d) Install the 4 bolts (A).

	Bolt (A)		Bolt (B)
	Nut	-	-

Torque:

25 N·m {255 kgf·cm, 18 ft·lbf}

(e) Connect the brake pedal assembly with the bolt (B).

Torque:

15 N·m {153 kgf·cm, 11 ft·lbf}

(f) Temporarily install the nut.

(g) Install the 3 bolts.

Torque:

25 N·m {255 kgf·cm, 18 ft·lbf}

(h) Install the 2 hole plugs.

(i) Install a new cooler unit drain hose grommet. NOTICE: If the drain cooler hose is disconnected from the cooler unit drain hose grommet, make sure to replace the cooler unit drain hose grommet with a new one. Failure to do so may lead to water ingress. Make sure that the entire lip of the cooler unit drain hose grommet is securely engaged to the vehicle body.

*a Lip

(j) Connect the drain cooler hose.

(k) Install the front floor mat to its original position as shown in the illustration.

(l) Engage each clamp.

*a	Lock Lever
	Move in this Direction

(m) Temporarily connect the connector and then move the lock lever as shown in the illustration to securely connect the connector.

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.

(n) Check that there is no looseness in the installed parts of the airbag sensor assembly.

(o) Connect the connector.

(p) Engage each clamp.

(q) Connect the connector holder with the 2 nuts.

Torque:

8.0 N·m {82 kgf·cm, 71 in·lbf}

(r) Connect the 3 earth wires with the 3 bolts.

Torque:

8.5 N·m {87 kgf·cm, 75 in·lbf}

(s) Connect the connector.

3. INSTALL INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU

Click here

4. INSTALL NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY

Click here

5. INSTALL NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

Click here

6. INSTALL NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

(a) Install the No. 1 instrument panel brace sub-assembly with the bolt and nut.

Torque:

Bolt :

20 N·m {204 kgf·cm, 15 ft·lbf}

Nut :

18 N·m {184 kgf·cm, 13 ft·lbf}

(b) Temporarily install the screw.

HINT:

Do not fully tighten the screw.

(c) Engage each clamp.

(d) Connect the earth wire with the bolt.

Torque:

8.5 N·m {87 kgf·cm, 75 in·lbf}

7. INSTALL AIR CONDITIONER UNIT ASSEMBLY

Click here

8. INSTALL NO. 3 DASH PANEL INSULATOR PAD

Click here

9. INSTALL NO. 1 CONSOLE BOX DUCT

Click here

10. INSTALL FLOOR CARPET BRACKET LH

Click here

11. INSTALL FLOOR CARPET BRACKET RH

Click here

12. INSTALL REAR NO. 3 AIR DUCT

Click here

13. INSTALL REAR NO. 4 AIR DUCT

Click here

14. INSTALL REAR NO. 1 AIR DUCT

Click here

15. INSTALL REAR NO. 2 AIR DUCT

Click here

16. INSTALL ACCELERATOR PEDAL

Click here

17. INSTALL ACCELERATOR PEDAL PAD

Click here

18. INSTALL COOLER (ROOM TEMP. SENSOR) THERMISTOR

Click here

19. INSTALL DRIVING SUPPORT ECU ASSEMBLY

Click here

20. INSTALL NO. 1 CLEARANCE WARNING BUZZER (w/ Intelligent Parking Assist System)

Click here

21. INSTALL DCM (TELEMATICS TRANSCEIVER) WITH BRACKET

Click here

22. INSTALL STEREO COMPONENT EQUALIZER ASSEMBLY (w/ Active Noise Control System)

Click here

23. INSTALL ECU INTEGRATION BOX RH

Click here

24. INSTALL INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY

Click here

25. INSTALL STEERING COLUMN ASSEMBLY

for Manual Tilt and Manual Telescopic Steering Column:

Click here

for Power Tilt and Power Telescopic Steering Column:

Click here

26. INSTALL TRANSMISSION FLOOR SHIFT ASSEMBLY

Click here

27. INSTALL FRONT SEAT ASSEMBLY LH

Click here

28. INSTALL FRONT SEAT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.

29. CONNECT NO. 2 AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY

(a) Remove the vinyl tape from the No. 2 air conditioning tube and accessory assembly.

(b) Sufficiently apply compressor oil to 2 new O-rings and the fitting surfaces of the No. 2 air conditioning tube and accessory assembly.

Compressor Oil:

ND-OIL 12 or equivalent

(c) Install the 2 O-rings to the No. 2 air conditioning tube and accessory assembly.

NOTICE:

Keep the O-rings and O-ring fitting surfaces free of foreign matter.

(d) Connect the No. 2 air conditioning tube and accessory assembly.

(e) Rotate the hook connector as shown in the illustration.

(f) Insert the tube joint into the fitting hole securely and install the bolt.

Torque:

9.8 N·m {100 kgf·cm, 87 in·lbf}

30. CONNECT INLET HEATER WATER HOSE

(a) Connect the inlet heater water hose with the marking facing up and engage the clip within the area shown in the illustration. NOTICE: Do not apply excessive force to the inlet heater water hose.

*a View A *b Marking (Yellow) *c Clip Installation Angle (270°)

31. CONNECT OUTLET HEATER WATER HOSE

(a) Connect the outlet heater water hose with the marking facing up and engage the clip within the area shown in the illustration. NOTICE: Do not apply excessive force to the outlet heater water hose.

*a View A *b Marking (Purple) *c Clip Installation Angle (270°)

32. INSTALL FRONT CENTER UPPER SUSPENSION BRACE SUB-ASSEMBLY

Click here

33. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Click here

34. ADD ENGINE COOLANT

Click here

35. INSPECT FOR COOLANT LEAK

Click here

36. CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT

Click here

37. WARM UP ENGINE

Click here

38. INSPECT FOR REFRIGERANT LEAK

Click here