Last Modified: 08-21-2023 6.11:8.1.0 Doc ID: RM100000001AWOL
Model Year Start: 2019 Model: Avalon HV Prod Date Range: [04/2018 - 08/2021]
Title: P710 (HYBRID TRANSMISSION / TRANSAXLE): SHIFT PADDLE SWITCH: REMOVAL; 2019 - 2021 MY Avalon HV [04/2018 - 08/2021]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during shift paddle switch (transmission shift switch assembly) removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link
*: When performing learning using the Techstream.

Click here 2019 - 2022 MY Avalon HV [04/2018 -        ]; PARK ASSIST / MONITORING: INTELLIGENT CLEARANCE SONAR SYSTEM (for HV Model): CALIBRATION

Auxiliary battery terminal is disconnected/reconnected

Perform steering sensor zero point calibration

Lane departure alert system (w/ Steering Control)

2019 - 2021 MY Avalon HV [04/2018 - 08/2021]; PRE-COLLISION: PRE-COLLISION SYSTEM (for HV Model): INITIALIZATION

Pre-collision system

Intelligent clearance sonar system*

Lighting system (w/ AFS)(EXT)

Memorize steering angle neutral point

Parking assist monitor system

2019 - 2022 MY Avalon HV [04/2018 -        ]; PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM(for HV Model): INITIALIZATION

Panoramic view monitor system

2019 - 2022 MY Avalon HV [04/2018 -        ]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM (for HV Model): INITIALIZATION

NOTICE:

  • Do not remove/install the spiral cable with sensor sub-assembly with the battery connected and the power switch on (IG).
  • Do not rotate the spiral cable with sensor sub-assembly without the steering wheel assembly installed, with the battery connected and the power switch on (IG).
  • Ensure that the steering wheel assembly is installed and aligned straight when inspecting the steering sensor.

PROCEDURE

1. REMOVE STEERING WHEEL ASSEMBLY

Click here 2019 - 2020 MY Avalon Avalon HV [04/2018 - 08/2020]; STEERING COLUMN: STEERING WHEEL: REMOVAL 2021 MY Avalon Avalon HV [08/2020 - 08/2021]; STEERING COLUMN: STEERING WHEEL: REMOVAL

2. REMOVE STEERING PAD SWITCH ASSEMBLY

Click here 2019 - 2021 MY Avalon Avalon HV [04/2018 - 08/2021]; STEERING COLUMN: STEERING PAD SWITCH: REMOVAL+

3. REMOVE SHIFT PADDLE SWITCH (TRANSMISSION SHIFT SWITCH ASSEMBLY)

(a) Remove the 2 screws.

(b) Disengage the 4 claws.

(c) Disengage the 2 clamps to disconnect the shift paddle switch (transmission shift switch assemby) from the steering wheel assembly.

(d) Disconnect the No. 1 transmission shift switch assembly connector and No. 2 transmission shift switch assembly connector to remove the No. 1 transmission shift switch assembly and No. 2 transmission shift switch assembly from the No. 1 switch wire.

*1

No.1 Transmission Shift Switch Assembly

*2

No.2 Transmission Shift Switch Assembly

4. REMOVE NO. 1 SWITCH WIRE

HINT:

Perform this procedure only when replacement of the No. 1 switch wire is necessary.

(a) Disengage the 2 guides and remove the No. 1 switch wire from the steering wheel assembly.