Last Modified: 08-21-2023 6.11:8.1.0 Doc ID: RM100000001AW9N
Model Year Start: 2019 Model: Avalon Prod Date Range: [04/2018 -           ]
Title: LIGHTING (INT): LIGHTING SYSTEM (for Gasoline Model): Ambient Illumination Light Circuit; 2019 - 2022 MY Avalon [04/2018 -        ]

Ambient Illumination Light Circuit

DESCRIPTION

The main body ECU (multiplex network body ECU) controls the operation of the following lights:

  • Front Door Inside Handle Illumination Light Assembly LH
  • Front Door Inside Handle Illumination Light Assembly RH
  • Center Console Light (for Passenger Side) (No. 2 Interior Illumination Light Sub-assembly)
  • Center Console Light (for Driver Side) (No. 3 Interior Illumination Light Sub-assembly)
  • Cup Holder Light (for Front Side) (No. 4 Interior Illumination Light Sub-assembly)
  • Cup Holder Light (for Rear Side) (No. 4 Interior Illumination Light Sub-assembly)

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

  • Inspect the fuses for circuits related to this system before performing the following procedure.
  • Before replacing the main body ECU (multiplex network body ECU), refer to Registration.

    Click here 2019 - 2020 MY Avalon [04/2018 - 08/2020]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, Gasoline Model): REGISTRATION 2021 - 2022 MY Avalon [08/2020 -        ]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, Gasoline Model): REGISTRATION

PROCEDURE

1.

PERFORM ACTIVE TEST USING TECHSTREAM

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Main Body / Active Test.

(e) Perform the Active Test according to the display on the Techstream.

Body Electrical > Main Body > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

Fr Foot Light

  • Front door inside handle illumination light assembly
  • Center console light (for passenger side) (No. 2 interior illumination light sub-assembly)
  • Center console light (for driver side) (No. 3 interior illumination light sub-assembly)
  • Cup holder light (No. 4 interior illumination light sub-assembly)

OFF or ON

Preconditions for using the Active Test to check dimmer controlled illumination:

  • Engine switch on (IG)
  • Ambient illumination lights turned off using the mood switch

Body Electrical > Main Body > Active Test

Tester Display

Fr Foot Light

OK:

Front door inside handle illumination lights, center console lights and cup holder lights come on.

Result

Proceed to

OK

A

NG (Front door inside handle illumination light LH does not come on)

B

NG (Front door inside handle illumination light RH does not come on)

C

NG (Center console light (for passenger side) does not come on)

D

NG (Center console light (for driver side) does not come on)

E

NG (Cup holder light (for front side) does not come on)

F

NG (Cup holder light (for rear side) does not come on)

G

NG (Front door inside handle illumination lights, center console lights and cup holder lights do not come on)

H

A

USE SIMULATION METHOD TO CHECK

C

GO TO STEP 4

D

GO TO STEP 6

E

GO TO STEP 8

F

GO TO STEP 10

G

GO TO STEP 12

H

GO TO STEP 14

B

2.

INSPECT FRONT DOOR INSIDE HANDLE ILLUMINATION LIGHT ASSEMBLY LH

(a) Remove the front door inside handle illumination light assembly LH.

Click here 2019 - 2022 MY Avalon Avalon HV [04/2018 -        ]; LIGHTING (INT): INSIDE HANDLE LIGHT: REMOVAL

(b) Inspect the front door inside handle illumination light assembly LH.

Click here 2019 - 2022 MY Avalon Avalon HV [04/2018 -        ]; LIGHTING (INT): INSIDE HANDLE LIGHT: INSPECTION

NG

REPLACE FRONT DOOR INSIDE HANDLE ILLUMINATION LIGHT ASSEMBLY LH

OK

3.

CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - FRONT DOOR INSIDE HANDLE ILLUMINATION LIGHT ASSEMBLY LH)

(a) Disconnect the 4A and 4D instrument panel junction block assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

4D-24 - I26-1 (+)

Always

Below 1 Ω

4A-36 - I26-2 (-)

Always

Below 1 Ω

OK

USE SIMULATION METHOD TO CHECK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.

INSPECT FRONT DOOR INSIDE HANDLE ILLUMINATION LIGHT ASSEMBLY RH

(a) Remove the front door inside handle illumination light assembly RH.

Click here 2019 - 2022 MY Avalon Avalon HV [04/2018 -        ]; LIGHTING (INT): INSIDE HANDLE LIGHT: REMOVAL

(b) Inspect the front door inside handle illumination light assembly RH.

Click here 2019 - 2022 MY Avalon Avalon HV [04/2018 -        ]; LIGHTING (INT): INSIDE HANDLE LIGHT: INSPECTION

NG

REPLACE FRONT DOOR INSIDE HANDLE ILLUMINATION LIGHT ASSEMBLY RH

OK

5.

CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - FRONT DOOR INSIDE HANDLE ILLUMINATION LIGHT ASSEMBLY RH)

(a) Disconnect the 4A and 4D instrument panel junction block assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

4D-24 - I10-1 (+)

Always

Below 1 Ω

4A-36 - I10-2 (-)

Always

Below 1 Ω

OK

USE SIMULATION METHOD TO CHECK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.

INSPECT CENTER CONSOLE LIGHT (for Passenger Side) (NO. 2 INTERIOR ILLUMINATION LIGHT SUB-ASSEMBLY)

(a) Remove the center console light (for passenger side) (No. 2 interior illumination light sub-assembly).

Click here 2019 - 2022 MY Avalon Avalon HV [04/2018 -        ]; LIGHTING (INT): AMBIENT LIGHT: REMOVAL

(b) Inspect the center console light (for passenger side) (No. 2 interior illumination light sub-assembly).

Click here 2019 - 2022 MY Avalon Avalon HV [04/2018 -        ]; LIGHTING (INT): AMBIENT LIGHT: INSPECTION

NG

REPLACE CENTER CONSOLE LIGHT (for Passenger Side) (NO. 2 INTERIOR ILLUMINATION LIGHT SUB-ASSEMBLY)

OK

7.

CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - CENTER CONSOLE LIGHT (for Passenger Side))

(a) Disconnect the 4A and 4D instrument panel junction block assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

4D-24 - G67-1 (+)

Always

Below 1 Ω

4A-36 - G67-2 (-)

Always

Below 1 Ω

OK

USE SIMULATION METHOD TO CHECK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.

INSPECT CENTER CONSOLE LIGHT (for Driver Side) (NO. 3 INTERIOR ILLUMINATION LIGHT SUB-ASSEMBLY)

(a) Remove the center console light (for driver side) (No. 3 interior illumination light sub-assembly).

Click here 2019 - 2022 MY Avalon Avalon HV [04/2018 -        ]; LIGHTING (INT): AMBIENT LIGHT: REMOVAL

(b) Inspect the center console light (for driver side) (No. 3 interior illumination light sub-assembly).

Click here 2019 - 2022 MY Avalon Avalon HV [04/2018 -        ]; LIGHTING (INT): AMBIENT LIGHT: INSPECTION

NG

REPLACE CENTER CONSOLE LIGHT (for Driver Side) (NO. 3 INTERIOR ILLUMINATION LIGHT SUB-ASSEMBLY)

OK

9.

CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - CENTER CONSOLE LIGHT (for Driver Side))

(a) Disconnect the 4A and 4D instrument panel junction block assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

4D-24 - G66-1 (+)

Always

Below 1 Ω

4A-36 - G66-2 (-)

Always

Below 1 Ω

OK

USE SIMULATION METHOD TO CHECK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.

INSPECT CUP HOLDER LIGHT (for Front Side) (NO. 4 INTERIOR ILLUMINATION LIGHT SUB-ASSEMBLY)

(a) Remove the cup holder light (for front side) (No. 4 interior illumination light sub-assembly).

Click here 2019 - 2022 MY Avalon Avalon HV [04/2018 -        ]; LIGHTING (INT): AMBIENT LIGHT: REMOVAL

(b) Inspect the cup holder light (for front side) (No. 4 interior illumination light sub-assembly).

Click here 2019 - 2022 MY Avalon Avalon HV [04/2018 -        ]; LIGHTING (INT): AMBIENT LIGHT: INSPECTION

NG

REPLACE CUP HOLDER LIGHT (for Front Side) (NO. 4 INTERIOR ILLUMINATION LIGHT SUB-ASSEMBLY)

OK

11.

CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - CUP HOLDER LIGHT (for Front Side))

(a) Disconnect the 4A and 4D instrument panel junction block assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

4D-24 - G64-1 (+)

Always

Below 1 Ω

4A-36 - G64-2 (-)

Always

Below 1 Ω

OK

USE SIMULATION METHOD TO CHECK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.

INSPECT CUP HOLDER LIGHT (for Rear Side) (NO. 4 INTERIOR ILLUMINATION LIGHT SUB-ASSEMBLY)

(a) Remove the cup holder light (for rear side) (No. 4 interior illumination light sub-assembly).

Click here 2019 - 2022 MY Avalon Avalon HV [04/2018 -        ]; LIGHTING (INT): AMBIENT LIGHT: REMOVAL

(b) Inspect the cup holder light (for rear side) (No. 4 interior illumination light sub-assembly).

Click here 2019 - 2022 MY Avalon Avalon HV [04/2018 -        ]; LIGHTING (INT): AMBIENT LIGHT: INSPECTION

NG

REPLACE CUP HOLDER LIGHT (for Rear Side) (NO. 4 INTERIOR ILLUMINATION LIGHT SUB-ASSEMBLY)

OK

13.

CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - CUP HOLDER LIGHT (for Rear Side))

(a) Disconnect the 4A and 4D instrument panel junction block assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

4D-24 - G65-1 (+)

Always

Below 1 Ω

4A-36 - G65-2 (-)

Always

Below 1 Ω

OK

USE SIMULATION METHOD TO CHECK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.

CHECK HARNESS AND CONNECTOR (POWER SOURCE - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

(a) Disconnect the 4K instrument panel junction block assembly connector.

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

4K-1 - Body ground

Always

11 to 14 V

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

15.

CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

*a

Component without harness connected

(Instrument Panel Junction Block Assembly)

-

-

(a) Disconnect the 4D instrument panel junction block assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

4D-24 - 4K-1

Always

Below 1 Ω

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY 2019 - 2021 MY Avalon Avalon HV [04/2018 - 08/2021]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL 2022 MY Avalon Avalon HV [08/2021 -        ]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL

OK

16.

CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - AMBIENT ILLUMINATION LIGHT)

(a) Disconnect the I26 front door inside handle illumination light assembly LH connector.

(b) Disconnect the I10 front door inside handle illumination light assembly RH connector.

(c) Disconnect the G67 center console light (for passenger side) (No. 2 interior illumination light sub-assembly) connector.

(d) Disconnect the G66 center console light (for driver side) (No. 3 interior illumination light sub-assembly) connector.

(e) Disconnect the G64 cup holder light (for front side) (No. 4 interior illumination light sub-assembly) connector.

(f) Disconnect the G65 cup holder light (for rear side) (No. 4 interior illumination light sub-assembly) connector.

(g) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

4D-24 - I26-1 (+)

Always

Below 1 Ω

4D-24 - I10-1 (+)

Always

Below 1 Ω

4D-24 - G64-1 (+)

Always

Below 1 Ω

4D-24 - G65-1 (+)

Always

Below 1 Ω

4D-24 - G66-1 (+)

Always

Below 1 Ω

4D-24 - G67-1 (+)

Always

Below 1 Ω

4A-36 - I26-2 (-)

Always

Below 1 Ω

4A-36 - I10-2 (-)

Always

Below 1 Ω

4A-36 - G64-2 (-)

Always

Below 1 Ω

4A-36 - G65-2 (-)

Always

Below 1 Ω

4A-36 - G66-2 (-)

Always

Below 1 Ω

4A-36 - G67-2 (-)

Always

Below 1 Ω

4D-24, I26-1 (+), I10-1 (+), G64-1 (+), G65-1 (+), G66-1 (+) or G67-1 (+) - Body ground

Always

10 kΩ or higher

4A-36, I26-2 (-), I10-2 (-), G64-2 (-), G65-2 (-), G66-2 (-) or G67-2 (-) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

17.

INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

*a

Component without harness connected

(Instrument Panel Junction Block Assembly)

-

-

(a) Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

Click here 2019 - 2021 MY Avalon Avalon HV [04/2018 - 08/2021]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL 2022 MY Avalon Avalon HV [08/2021 -        ]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

4A-36 - MB-26 (FSPT)

Always

Below 1 Ω

OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) 2019 - 2021 MY Avalon Avalon HV [04/2018 - 08/2021]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL 2022 MY Avalon Avalon HV [08/2021 -        ]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY 2019 - 2021 MY Avalon Avalon HV [04/2018 - 08/2021]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL 2022 MY Avalon Avalon HV [08/2021 -        ]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL