Last Modified: 08-21-2023 |
6.11:8.1.0 |
Doc ID: RM100000001AW8S |
Model Year Start: 2019 |
Model: Avalon HV |
Prod Date Range: [04/2018 - 08/2021] |
Title: TIRE PRESSURE MONITORING: TIRE PRESSURE WARNING RECEIVER: REMOVAL; 2019 - 2021 MY Avalon Avalon HV [04/2018 - 08/2021] |
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during tire pressure warning ECU and receiver removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)
Replacement Part or Procedure
|
Necessary Procedures
|
Effects/Inoperative when not Performed
|
Link
|
Disconnect cable from battery terminal
|
Perform steering sensor zero point calibration
|
Lane Departure Alert System (w/ Steering Control)
|
|
Pre-collision System
|
Intelligent Clearance Sonar System*
|
Lighting System (for Gasoline Model with Cornering Light)
|
Memorize steering angle neutral point
|
Parking Assist Monitor System
|
|
Panoramic View Monitor System
|
|
Tire pressure warning ECU and receiver
|
-
Register transmitter ID
-
Initialize tire pressure warning system
|
-
When DTC detection conditions of "transmitter ID not received" DTC are met, TPWS indicator blinks for 1 minute, and then illuminates
-
Tire pressure warning function
|
for Registration
for Initialization
|
Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replacement Part or Procedure
|
Necessary Procedures
|
Effects/Inoperative when not Performed
|
Link
|
Disconnect cable from negative auxiliary battery terminal
|
Perform steering sensor zero point calibration
|
Lane Departure Alert System (w/ Steering Control)
|
|
Pre-collision System
|
Intelligent Clearance Sonar System*
|
Lighting System (for HV Model with Cornering Light)
|
Memorize steering angle neutral point
|
Parking Assist Monitor System
|
|
Panoramic View Monitor System
|
|
Tire pressure warning ECU and receiver
|
-
Register transmitter ID
-
Initialize tire pressure warning system
|
-
When DTC detection conditions of "transmitter ID not received" DTC are met, TPWS indicator blinks for 1 minute, and then illuminates
-
Tire pressure warning function
|
for Registration
for Initialization
|
CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.
for Gasoline Model: Click here
for HV Model: Click here
NOTICE:
When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the Techstream and write them down before removal.
for HV Model: Click here
for Gasoline Model: Click here
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the engine switch (for Gasoline Model) or power switch (for HV Model) off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here
2. REMOVE ROOF SIDE INNER GARNISH RH
Click here
3. REMOVE TIRE PRESSURE WARNING ECU AND RECEIVER
NOTICE:
-
Do not drop the tire pressure warning ECU and receiver, strike it with tools or subject it to impact.
-
If the tire pressure warning ECU and receiver is subjected to an impact, replace it with a new one.
(b) Disengage the 2 guides.
(c) Disconnect the connector to remove the tire pressure warning ECU and receiver.
|