| Last Modified: 08-21-2023 | 6.11:8.1.0 | Doc ID: RM100000001ATT0 |
| Model Year Start: 2019 | Model: Avalon HV | Prod Date Range: [04/2018 - 08/2021] |
| Title: AUDIO / VIDEO: REAR PACKAGE TRAY SPEAKER: REMOVAL; 2019 - 2021 MY Avalon Avalon HV [04/2018 - 08/2021] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear package tray speaker removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function When Necessary Procedures are not Performed |
Link |
|---|---|---|---|
|
*: When performing learning using the Techstream.
Click here
|
|||
|
Disconnect cable from negative battery terminal |
Perform steering sensor zero point calibration |
Lane Departure Alert System (w/ Steering Control) |
|
|
Pre-collision System |
|||
|
Intelligent Clearance Sonar System* |
|||
|
Lighting System (for Gasoline Model with Cornering Light) |
|||
|
Memorize steering angle neutral point |
Parking Assist Monitor System |
|
|
|
Panoramic View Monitor System |
|
||
CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.
Click here
![2019 - 2020 MY Avalon [04/2018 - 08/2020]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (for Gasoline Model): PRECAUTION](/t3Portal/stylegraphics/info.gif)
Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function When Necessary Procedures are not Performed |
Link |
|---|---|---|---|
|
*: When performing learning using the Techstream.
Click here
|
|||
|
Disconnect cable from negative auxiliary battery terminal |
Perform steering sensor zero point calibration |
Lane Departure Alert System (w/ Steering Control) |
|
|
Pre-collision System |
|||
|
Intelligent Clearance Sonar System* |
|||
|
Lighting System (for HV Model with Cornering Light) |
|||
|
Memorize steering angle neutral point |
Parking Assist Monitor System |
|
|
|
Panoramic View Monitor System |
|
||
CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.
Click here
PROCEDURE
1. REMOVE REAR SEAT ASSEMBLY
Click here
2. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH
Click here
3. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH
HINT:
Use the same procedure as for the LH side.
4. REMOVE ROOF SIDE RAIL GARNISH ASSEMBLY LH
Click here
5. REMOVE ROOF SIDE RAIL GARNISH ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
6. REMOVE ROOF SIDE INNER GARNISH LH
Click here
7. REMOVE ROOF SIDE INNER GARNISH RH
HINT:
Use the same procedure as for the LH side.
8. DISCONNECT REAR SEAT 3 POINT TYPE BELT ASSEMBLY LH
Click here
9. DISCONNECT REAR SEAT 3 POINT TYPE BELT ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
10. REMOVE CENTER STOP LIGHT SET
Click here
11. REMOVE REAR SEAT SHOULDER BELT COVER
Click here
12. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY
Click here
13. REMOVE REAR NO. 3 SPEAKER ASSEMBLY
NOTICE:
Do not touch the speaker cone.
|
(a) Disconnect the connector. |
|
|
(b) Remove the 4 bolts and disengage the guide to remove the rear No. 3 speaker assembly. |
|
14. REMOVE SPARE WHEEL COVER ASSEMBLY (w/o Seat Heater System)
Click here
15. REMOVE LUGGAGE COMPARTMENT INNER TRIM PAD (w/o Seat Heater System)
Click here
16. REMOVE ROOM PARTITION BOARD LH
Click here
17. REMOVE ROOM PARTITION BOARD RH
Click here
18. REMOVE NO. 1 UPPER BACK PANEL HOLE COVER
(a) Remove the No. 1 upper back panel hole cover as shown in the illustration.
|
Remove in this Direction |
19. REMOVE SPEAKER ASSEMBLY WITH BRACKET
NOTICE:
Do not touch the speaker cone.
(a) for LH Side:
|
(1) Remove the 2 bolts and disengage the guide. |
|
|
(2) Disconnect the connector to remove the speaker assembly with bracket. |
|
(b) for RH Side:
|
(1) Disconnect the connector. |
|
|
(2) Remove the 2 bolts and disengage the guide to remove the speaker assembly with bracket. |
|
|
|