Last Modified: 08-21-2023 |
6.11:8.1.0 |
Doc ID: RM100000001AT1N |
Model Year Start: 2019 |
Model: Avalon HV |
Prod Date Range: [04/2018 - 08/2021] |
Title: SLIDING ROOF / CONVERTIBLE: SLIDING ROOF HOUSING: REMOVAL; 2019 - 2021 MY Avalon Avalon HV [04/2018 - 08/2021] |
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during sliding roof housing removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure
|
Necessary Procedure
|
Effect/Inoperative Function when Necessary Procedure not Performed
|
Link
|
Disconnect cable from negative (-) battery terminal
|
Perform steering sensor zero point calibration
|
Lane Departure Alert System (w/ Steering Control)
|
|
Pre-collision System
|
Intelligent Clearance Sonar System*
|
Lighting System (for Gasoline Model with Cornering Light)
|
Memorize steering angle neutral point
|
Parking Assist Monitor System
|
|
Panoramic View Monitor System
|
Front passenger seat
|
Zero point calibration (Occupant classification system)
|
-
Occupant classification system
-
Passenger airbag ON/OFF indicator
-
Airbag system (Front passenger side)
-
Seat belt warning system (Front passenger)
|
|
-
Sliding roof ECU (sliding roof drive gear sub-assembly)
-
Sliding roof glass sub-assembly
-
Sliding roof drive cable sub-assembly
-
Sliding roof drive gear sub-assembly
|
Initialize sliding roof system
|
-
Auto operation function
-
Jam protection function
-
Key-off operation function
-
Key-linked function
-
Wireless transmitter-linked function
-
Sliding roof open warning function
|
|
Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure
|
Necessary Procedure
|
Effect/Inoperative Function when Necessary Procedure not Performed
|
Link
|
Disconnect cable from negative (-) auxiliary battery terminal
|
Perform steering sensor zero point calibration
|
Lane Departure Alert System (w/ Steering Control)
|
|
Pre-collision System
|
Intelligent Clearance Sonar System*
|
Lighting System (for HV Model with Cornering Light)
|
Memorize steering angle neutral point
|
Parking Assist Monitor System
|
|
Panoramic View Monitor System
|
Front passenger seat
|
Zero point calibration (Occupant classification system)
|
-
Occupant classification system
-
Passenger airbag ON/OFF indicator
-
Airbag system (Front passenger side)
-
Seat belt warning system (Front passenger)
|
|
-
Sliding roof ECU (sliding roof drive gear sub-assembly)
-
Sliding roof glass sub-assembly
-
Sliding roof drive cable sub-assembly
-
Sliding roof drive gear sub-assembly
|
Initialize sliding roof system
|
-
Auto operation function
-
Jam protection function
-
Key-off operation function
-
Key-linked function
-
Wireless transmitter-linked function
-
Sliding roof open warning function
|
|
CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.
for Gasoline Model: Click here
for HV Model: Click here
PROCEDURE
1. REMOVE SLIDING ROOF SIDE GARNISH LH
(a) Disengage the 4 claws to remove the sliding roof side garnish LH.
|
|
2. REMOVE SLIDING ROOF SIDE GARNISH RH
HINT:
Use the same procedure as for the LH side.
3. REMOVE SLIDING ROOF GLASS SUB-ASSEMBLY
(a) Move the sliding roof glass sub-assembly to the fully closed position.
(b) Using a T25 "TORX" socket wrench, remove the 4 screws and sliding roof glass sub-assembly.
NOTICE:
To prevent the sliding roof glass sub-assembly and sliding roof drive gear assembly from becoming misaligned, move the sliding roof glass sub-assembly (sliding roof drive cable sub-assembly) to the fully closed position before removing it.
4. REMOVE SLIDING ROOF WEATHERSTRIP
(a) Remove the sliding roof weatherstrip from the sliding roof panel sub-assembly.
|
|
5. REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY LH
Click here
6. REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
7. DISCONNECT SLIDING ROOF DRAIN HOSE
HINT:
Use the same procedure for all of the sliding roof drain hoses.
(a) for Clamp Type:
(1) Disengage the claw and disconnect the sliding roof drain hose.
|
|
(b) for Clip Type:
(1) Expand the clip and disconnect the sliding roof drain hose.
|
|
8. REMOVE SLIDING ROOF HOUSING ASSEMBLY
(a) Remove the 8 bolts, 6 nuts and sliding roof housing assembly.
|