Last Modified: 08-21-2023 |
6.11:8.1.0 |
Doc ID: RM100000001ARAC |
Model Year Start: 2019 |
Model: Avalon HV |
Prod Date Range: [04/2018 - 08/2021] |
Title: SUPPLEMENTAL RESTRAINT SYSTEMS: FRONT PASSENGER AIRBAG ASSEMBLY: REMOVAL; 2019 - 2021 MY Avalon Avalon HV [04/2018 - 08/2021] |
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during instrument panel passenger airbag assembly removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure
|
Necessary Procedure
|
Effect/Inoperative Function when Necessary Procedure not Performed
|
Link
|
Disconnect cable from negative auxiliary battery terminal
|
Perform steering sensor zero point calibration
|
Lane Departure Alert System (w/ Steering Control)
|
|
Pre-collision System
|
Intelligent Clearance Sonar System*
|
Lighting System (for Gasoline Model with Cornering Light)
|
Memorize steering angle neutral point
|
Parking Assist Monitor System
|
|
Panoramic View Monitor System
|
|
Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure
|
Necessary Procedure
|
Effect/Inoperative Function when Necessary Procedure not Performed
|
Link
|
Disconnect cable from negative auxiliary battery terminal
|
Perform steering sensor zero point calibration
|
Lane Departure Alert System (w/ Steering Control)
|
|
Pre-collision System
|
Intelligent Clearance Sonar System*
|
Lighting System (for HV Model with Cornering Light)
|
Memorize steering angle neutral point
|
Parking Assist Monitor System
|
|
Panoramic View Monitor System
|
|
PROCEDURE
1. PRECAUTION
CAUTION:
Be sure to read Precaution thoroughly before servicing.
for Gasoline Model: Click here
for HV Model: Click here
NOTICE:
After turning the engine switch (for Gasoline Model) or power switch (for HV Model) off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here
2. REMOVE TURN SIGNAL SWITCH
Click here
3. DISCONNECT NO. 2 INSTRUMENT PANEL WIRE
(a) Check that the engine switch (for Gasoline Model) or power switch (for HV Model) is off.
(b) Check that the cable is disconnected from the negative (-) auxiliary battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
(c) Disengage the clamp.
*a
|
Slider
|
|
Release in this Direction
|
(d) Slide the slider to release the lock, and then disconnect the connector.
NOTICE:
When disconnecting any airbag connector, take care not to damage the airbag wire harness.
4. REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY
Click here
5. REMOVE INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY
CAUTION:
When storing the instrument panel passenger airbag assembly, keep the airbag deployment side facing upward.
|
Deployment Side
|
(b) Using a screwdriver, pry back the passenger airbag door retainer to disengage the 3 hooks as shown in the illustration.
*a
|
Passenger Airbag Door Retainer
|
|
Move the screwdriver in this Direction
|
NOTICE:
Do not damage the deployment surface of the instrument panel passenger airbag assembly.
(c) Disengage the 3 hooks to remove the instrument panel passenger airbag assembly from the instrument panel safety pad sub-assembly.
|
|
6. REMOVE NO. 2 INSTRUMENT PANEL WIRE
(a) Disengage the clamp.
*a
|
Protective Tape
|
*b
|
Airbag Connector
|
*c
|
Airbag Connector Locking Button
|
|
Release in this Direction
|
(b) Using a screwdriver with its tip wrapped with protective tape, release the 2 airbag connector locking buttons.
(c) Disconnect the 2 airbag connectors to remove the No. 2 instrument panel wire from the instrument panel passenger airbag assembly.
NOTICE:
When disconnecting any airbag connector, take care not to damage the airbag wire harness.
|