Last Modified: 08-21-2023 6.11:8.1.0 Doc ID: RM100000001AR9X
Model Year Start: 2019 Model: Avalon HV Prod Date Range: [04/2018 - 08/2020]
Title: SUPPLEMENTAL RESTRAINT SYSTEMS: SPIRAL CABLE: INSTALLATION; 2019 - 2020 MY Avalon Avalon HV [04/2018 - 08/2020]

INSTALLATION

PROCEDURE

1. INSPECT SPIRAL CABLE SUB-ASSEMBLY

NOTICE:

If the steering sensor is installed to a misaligned spiral cable sub-assembly, spiral cable with sensor sub-assembly malfunction DTCs, such as DTC B1801, C1231 and C1433, will be stored and it will be impossible to clear them. If this happens, replace the spiral cable sub-assembly and steering sensor with a new one.

(a) Check if the spiral cable sub-assembly is centered.

OK:

  • The connector is positioned at the top.
  • The alignment marks are aligned correctly.
  • The colored roller or flat cable can be seen in the inspection window.

*A

w/o Heated Steering Wheel System

*B

w/ Heated Steering Wheel System

*a

Inspection Window

*b

Alignment Mark

*c

Colored Roller

*d

Flat Cable

(b) If the spiral cable sub-assembly is not centered, center it.

NOTICE:

Make sure to observe the following precautions, otherwise the spiral cable sub-assembly may be damaged.

  • Release the interlock before rotating the spiral cable sub-assembly.
  • Do not rotate the spiral cable sub-assembly using the airbag wire harness.
  • Do not rotate the spiral cable sub-assembly with excessive force.

(1) While pushing on the interlock shown in the illustration, rotate the spiral cable sub-assembly counterclockwise slowly by hand until it stops.

*A

w/o Heated Steering Wheel System

*B

w/ Heated Steering Wheel System

*a

Interlock

Rotation Direction

NOTICE:

If the spiral cable sub-assembly is rotated clockwise in this step, it may be damaged and may no longer be able to be centered. Make sure to only rotate the spiral cable sub-assembly counterclockwise.

HINT:

If the interlock is engaged, the spiral cable sub-assembly will lock when the connector is near at the top or bottom of the rotation of the spiral cable sub-assembly.

(2) If the connector is not positioned at the bottom of the rotation of the spiral cable sub-assembly when the spiral cable sub-assembly is turned until it stops, turn the spiral cable sub-assembly clockwise until the connector is positioned at the bottom as shown in the illustration.

*A

w/o Heated Steering Wheel System

*B

w/ Heated Steering Wheel System

(3) While pushing on the interlock shown in the illustration, rotate the spiral cable sub-assembly clockwise approximately 2.5 times.

*A

w/o Heated Steering Wheel System

*B

w/ Heated Steering Wheel System

*a

Interlock

Rotation Direction

NOTICE:

If the spiral cable sub-assembly is rotated clockwise 5 times or more from the point at which it stops and the connector is positioned at the bottom, the spiral cable sub-assembly may be damaged.

HINT:

If the interlock is engaged, the spiral cable sub-assembly will lock when the connector is near at the top or bottom of the rotation of the spiral cable sub-assembly.

(4) Check that the spiral cable sub-assembly is centered.

OK:

  • The connector is positioned at the top.
  • The alignment marks are aligned correctly.
  • The colored roller or flat cable can be seen in the inspection window.

*A

w/o Heated Steering Wheel System

*B

w/ Heated Steering Wheel System

*a

Inspection Window

*b

Alignment Mark

*c

Colored Roller

*d

Flat Cable

2. INSTALL SPIRAL CABLE SUB-ASSEMBLY

(a) Align the 2 pins and 2 guides, and engage the 6 claws to install the spiral cable sub-assembly to the steering sensor.

NOTICE:

  • Do not remove the lock pin before the spiral cable sub-assembly is installed to the steering sensor.
  • Do not damage the pins of the spiral cable sub-assembly or guides of the steering sensor.
  • The spiral cable sub-assembly can be rotated up to 30° even when the interlock is engaged. Therefore, make sure that both guides are aligned properly when installing the spiral cable sub-assembly to the steering sensor.

*a

Guide

*b

Pin

*c

Lock Pin

(b) Remove the lock pin from the steering sensor.

3. INSTALL SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

NOTICE:

  • Do not remove/install the spiral cable with sensor sub-assembly with the auxiliary battery connected and the engine switch (for Gasoline Model) or power switch (for HV Model) on (IG).
  • Do not rotate the spiral cable with sensor sub-assembly without the steering wheel assembly installed, with the auxiliary battery connected and the engine switch (for Gasoline Model) or power switch (for HV Model) on (IG).
  • Ensure that the steering wheel assembly is installed and aligned straight when inspecting the steering sensor.

(a) Check that the engine switch (for Gasoline Model) or power switch (for HV Model) is off.

(b) Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

(c) Check that the front wheels are aligned facing straight ahead.

(d) Engage the claw and 2 clips to install the spiral cable with sensor sub-assembly.

(e) Install the wire harness to the spiral cable with sensor sub-assembly as shown in the illustration.

Install in this Direction

(f) Connect each connector.

4. INSTALL UPPER STEERING COLUMN COVER (for Manual Tilt and Manual Telescopic Steering Column)

Click here 2019 - 2022 MY Avalon Avalon HV [04/2018 -        ]; STEERING COLUMN: STEERING COLUMN ASSEMBLY (for Manual Tilt and Manual Telescopic Steering Column): INSTALLATION+

5. INSTALL UPPER STEERING COLUMN COVER (for Power Tilt and Power Telescopic Steering Column)

Click here 2019 - 2022 MY Avalon Avalon HV [04/2018 -        ]; STEERING COLUMN: STEERING COLUMN ASSEMBLY (for Power Tilt and Power Telescopic Steering Column): INSTALLATION+

6. INSTALL LOWER STEERING COLUMN COVER (for Manual Tilt and Manual Telescopic Steering Column)

Click here 2019 - 2022 MY Avalon Avalon HV [04/2018 -        ]; STEERING COLUMN: STEERING COLUMN ASSEMBLY (for Manual Tilt and Manual Telescopic Steering Column): INSTALLATION+

7. INSTALL LOWER STEERING COLUMN COVER (for Power Tilt and Power Telescopic Steering Column)

Click here 2019 - 2022 MY Avalon Avalon HV [04/2018 -        ]; STEERING COLUMN: STEERING COLUMN ASSEMBLY (for Power Tilt and Power Telescopic Steering Column): INSTALLATION+

8. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

9. INSPECT AND ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

(a) Check that the engine switch (for Gasoline Model) or power switch (for HV Model) is off.

(b) Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

(c) Check if the spiral cable with sensor sub-assembly is centered.

OK:

  • The connector is positioned at the top.
  • The colored roller or flat cable can be seen in the inspection window.

*A

w/o Heated Steering Wheel System

*B

w/ Heated Steering Wheel System

*a

Inspection Window

*b

Colored Roller

*c

Flat Cable

(d) If the spiral cable with sensor sub-assembly is not centered, center it.

NOTICE:

Make sure to observe the following precautions, otherwise the spiral cable with sensor sub-assembly may be damaged.

  • Do not rotate the spiral cable with sensor sub-assembly with the auxiliary battery connected and the engine switch (for Gasoline Model) or power switch (for HV Model) on (IG).
  • Release the interlock before rotating the spiral cable with sensor sub-assembly.
  • Do not rotate the spiral cable with sensor sub-assembly using the airbag wire harness.
  • Do not rotate the spiral cable with sensor sub-assembly with excessive force.

(1) While pushing on the interlock shown in the illustration, rotate the spiral cable with sensor sub-assembly counterclockwise slowly by hand until it stops.

*A

w/o Heated Steering Wheel System

*B

w/ Heated Steering Wheel System

*a

Interlock

Rotation Direction

NOTICE:

If the spiral cable with sensor sub-assembly is rotated clockwise in this step, it may be damaged and may no longer be able to be centered. Make sure to only rotate the spiral cable with sensor sub-assembly counterclockwise.

HINT:

If the interlock is engaged, the spiral cable with sensor sub-assembly will lock when the connector is near at the top or bottom of the rotation of the spiral cable with sensor sub-assembly.

(2) If the connector is not positioned at the bottom of the rotation of the spiral cable with sensor sub-assembly when the spiral cable with sensor sub-assembly is turned until it stops, turn the spiral cable with sensor sub-assembly clockwise until the connector is positioned at the bottom as shown in the illustration.

*A

w/o Heated Steering Wheel System

*B

w/ Heated Steering Wheel System

(3) While pushing on the interlock shown in the illustration, rotate the spiral cable with sensor sub-assembly clockwise approximately 2.5 times.

*A

w/o Heated Steering Wheel System

*B

w/ Heated Steering Wheel System

*a

Interlock

Rotation Direction

NOTICE:

If the spiral cable with sensor sub-assembly is rotated clockwise 5 times or more from the point at which it stops and the connector is positioned at the bottom, the spiral cable with sensor sub-assembly may be damaged.

HINT:

If the interlock is engaged, the spiral cable with sensor sub-assembly will lock when the connector is near at the top or bottom of the rotation of the spiral cable with sensor sub-assembly.

(4) Check that the spiral cable with sensor sub-assembly is centered.

OK:

  • The connector is positioned at the top.
  • The colored roller or flat cable can be seen in the inspection window.

NOTICE:

If the spiral cable with sensor sub-assembly cannot be centered, it may be damaged. Replace the spiral cable sub-assembly and steering sensor with a new one.

*A

w/o Heated Steering Wheel System

*B

w/ Heated Steering Wheel System

*a

Inspection Window

*b

Colored Roller

*c

Flat Cable

10. INSTALL STEERING WHEEL ASSEMBLY

Click here 2019 - 2020 MY Avalon Avalon HV [04/2018 - 08/2020]; STEERING COLUMN: STEERING WHEEL: INSTALLATION+

11. CHECK STEERING WHEEL CENTER POINT

12. INSTALL HORN BUTTON ASSEMBLY

Click here 2019 - 2020 MY Avalon Avalon HV [04/2018 - 08/2020]; SUPPLEMENTAL RESTRAINT SYSTEMS: STEERING PAD: INSTALLATION+

13. INSTALL LOWER NO. 2 STEERING WHEEL COVER (w/ Cover)

Click here 2019 - 2020 MY Avalon Avalon HV [04/2018 - 08/2020]; SUPPLEMENTAL RESTRAINT SYSTEMS: STEERING PAD: INSTALLATION+

14. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

for Gasoline Model: Click here 2019 - 2022 MY Avalon [04/2018 -        ]; MAINTENANCE: 2GR-FKS BATTERY: INSTALLATION+

for HV Model: Click here 2019 - 2022 MY Avalon HV [04/2018 -        ]; MAINTENANCE: A25A-FXS AUXILIARY BATTERY: INSTALLATION+

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click here 2019 - 2020 MY Avalon Avalon HV [04/2018 - 08/2020]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION

15. INSTALL LUGGAGE TRIM SERVICE HOLE COVER (for HV Model)

Click here 2019 - 2022 MY Avalon HV [04/2018 -        ]; MAINTENANCE: A25A-FXS AUXILIARY BATTERY: INSTALLATION+

16. INSPECT HORN BUTTON ASSEMBLY

(a) Make sure that the horn sounds.

If the horn does not sound, inspect the horn system.

Click here 2019 - 2022 MY Avalon Avalon HV [04/2018 -        ]; HORN: HORN SYSTEM: PROBLEM SYMPTOMS TABLE

17. PERFORM DIAGNOSTIC SYSTEM CHECK

for Gasoline Model: Click here 2019 - 2022 MY Avalon [04/2018 -        ]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (for Gasoline Model): DTC CHECK / CLEAR

for HV Model: Click here 2019 - 2022 MY Avalon HV [04/2018 -        ]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (for HV Model): DTC CHECK / CLEAR

18. INSPECT SRS WARNING LIGHT

for Gasoline Model: Click here 2019 - 2022 MY Avalon [04/2018 -        ]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (for Gasoline Model): OPERATION CHECK

for HV Model: Click here 2019 - 2022 MY Avalon HV [04/2018 -        ]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (for HV Model): OPERATION CHECK

19. CUSTOMIZE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM (for Power Tilt and Power Telescopic Steering Column)

Click here 2019 - 2022 MY Avalon Avalon HV [04/2018 -        ]; STEERING COLUMN: STEERING COLUMN ASSEMBLY (for Power Tilt and Power Telescopic Steering Column): INSTALLATION+

20. PERFORM INITIALIZATION AND CALIBRATION (for Gasoline Model)

for Parking Assist Monitor System Initialization: Click here 2019 - 2022 MY Avalon [04/2018 -        ]; PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM (for Gasoline Model): INITIALIZATION

for Parking Assist Monitor System Calibration: Click here 2019 - 2022 MY Avalon [04/2018 -        ]; PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM (for Gasoline Model): CALIBRATION

for Panoramic View Monitor System Initialization: Click here 2019 - 2022 MY Avalon [04/2018 -        ]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM (for Gasoline Model): INITIALIZATION

for Panoramic View Monitor System Calibration: Click here 2019 - 2022 MY Avalon [04/2018 -        ]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM (for Gasoline Model): CALIBRATION

for Intelligent Clearance Sonar System Calibration: Click here 2019 - 2022 MY Avalon [04/2018 -        ]; PARK ASSIST / MONITORING: INTELLIGENT CLEARANCE SONAR SYSTEM (for Gasoline Model): CALIBRATION

21. PERFORM INITIALIZATION AND CALIBRATION (for HV Model)

for Parking Assist Monitor System Initialization: Click here 2019 - 2022 MY Avalon HV [04/2018 -        ]; PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM(for HV Model): INITIALIZATION

for Parking Assist Monitor System Calibration: Click here 2019 - 2022 MY Avalon HV [04/2018 -        ]; PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM(for HV Model): CALIBRATION

for Panoramic View Monitor System Initialization: Click here 2019 - 2022 MY Avalon HV [04/2018 -        ]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM (for HV Model): INITIALIZATION

for Panoramic View Monitor System Calibration: Click here 2019 - 2022 MY Avalon HV [04/2018 -        ]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM (for HV Model): CALIBRATION

for Intelligent Clearance Sonar System Calibration: Click here 2019 - 2022 MY Avalon HV [04/2018 -        ]; PARK ASSIST / MONITORING: INTELLIGENT CLEARANCE SONAR SYSTEM (for HV Model): CALIBRATION