| Last Modified: 08-21-2023 | 6.11:8.1.0 | Doc ID: RM100000001AR89 |
| Model Year Start: 2019 | Model: Avalon HV | Prod Date Range: [04/2018 - ] |
| Title: SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (for HV Model): B162B,B162C; Side Airbag Sensor Assembly No.2 Lost Communication (RH); 2019 - 2022 MY Avalon HV [04/2018 - ] | ||
|
DTC |
B162B |
Side Airbag Sensor Assembly No.2 Lost Communication (RH) |
|
DTC |
B162C |
Side Airbag Sensor Assembly No.2 Initialization Error (RH) |
DESCRIPTION
The side collision sensor RH circuit (bus 2) consists of the airbag ECU assembly and side No. 1 airbag sensor RH.
The side No. 1 airbag sensor RH detects impacts to the vehicle and sends signals to the airbag ECU assembly to determine if the airbags and pretensioners should be deployed.
These DTCs are stored when a malfunction is detected in the side collision sensor RH circuit (bus 2).
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
Warning Indicate |
Test Mode / Check Mode |
|---|---|---|---|---|---|
|
B162B |
Side Airbag Sensor Assembly No.2 Lost Communication (RH) |
|
|
Comes on |
Does not apply to test/check mode |
|
B162C |
Side Airbag Sensor Assembly No.2 Initialization Error (RH) |
|
|
Comes on |
Does not apply to test/check mode |
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here
![2019 - 2022 MY Avalon Avalon HV [04/2018 - ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION](/t3Portal/stylegraphics/info.gif)
PROCEDURE
|
1. |
CHECK CONNECTION OF CONNECTORS |
(a) Turn the power switch off.
(b) Disconnect the cable from the negative (-) auxiliary battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
(c) Check that the connectors are properly connected to the airbag ECU assembly and side No. 1 airbag sensor RH.
OK:
The connectors are properly connected.
| NG |
|
CONNECT CONNECTORS PROPERLY |
|
|
2. |
CHECK CONNECTORS |
(a) Disconnect the connectors from the airbag ECU assembly and side No. 1 airbag sensor RH.
(b) Check that the terminals of the connectors are not deformed or damaged.
OK:
The terminals are not deformed or damaged.
| NG |
|
REPLACE FLOOR WIRE |
|
|
3. |
CHECK FLOOR WIRE |
|
(a) Connect the cable to the negative (-) auxiliary battery terminal. |
|
(b) Turn the power switch on (IG).
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
K32-2 (BFR+) - Body ground |
Power switch on (IG) |
Below 1 V |
|
K32-1 (BFR-) - Body ground |
Power switch on (IG) |
Below 1 V |
(d) Turn the power switch off.
(e) Disconnect the cable from the negative (-) auxiliary battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
(f) Using a service wire, connect terminals 28 (BCR+) and 27 (BCR-) of connector B.
NOTICE:
Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.
(g) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
K32-2 (BFR+) - K32-1 (BFR-) |
Always |
Below 1 Ω |
(h) Disconnect the service wire from connector B.
(i) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
K32-2 (BFR+) - K32-1 (BFR-) |
Always |
1 MΩ or higher |
|
K32-2 (BFR+) - Body ground |
Always |
1 MΩ or higher |
|
K32-1 (BFR-) - Body ground |
Always |
1 MΩ or higher |
| NG |
|
REPLACE FLOOR WIRE |
|
|
4. |
CHECK SIDE NO. 1 AIRBAG SENSOR RH |
|
(a) Connect the connector to the airbag ECU assembly. |
|
(b) Interchange the side No. 1 airbag sensor RH with LH and connect the connectors.
(c) Connect the cable to the negative (-) auxiliary battery terminal.
(d) Turn the power switch on (IG), and wait for at least 60 seconds.
(e) Clear the DTCs stored in memory.
Body Electrical > SRS Airbag > Clear DTCs
(f) Turn the power switch off.
(g) Turn the power switch on (IG), and wait for at least 60 seconds.
(h) Check for DTCs.
Body Electrical > SRS Airbag > Trouble Codes
HINT:
Codes other than DTCs B162B, B162C, B163B and B163C may be output at this time, but they are not related to this check.
|
Result |
Proceed to |
|---|---|
|
DTC B162B or B162C is output. |
A |
|
DTC B163B or B163C is output. |
B |
|
DTCs B162B, B162C, B163B and B163C are not output. |
C |
(i) Turn the power switch off.
(j) Disconnect the cable from the negative (-) auxiliary battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
(k) Return the side No. 1 airbag sensor RH and LH to their original positions and connect the connectors.
| A |
|
REPLACE AIRBAG ECU ASSEMBLY
|
| B |
|
REPLACE SIDE NO. 1 AIRBAG SENSOR RH
|
| C |
|
|
|