| Last Modified: 09-10-2025 | 6.11:8.1.0 | Doc ID: RM100000001AOU4 |
| Model Year Start: 2019 | Model: Avalon HV | Prod Date Range: [04/2018 - 08/2019] |
| Title: EXTERIOR PANELS / TRIM: FRONT BUMPER: REASSEMBLY; 2019 MY Avalon HV Avalon [04/2018 - 08/2019] | ||
REASSEMBLY
PROCEDURE
PROCEDURE
1. INSTALL FRONT BUMPER REINFORCEMENT
(a) Install the front bumper reinforcement with the 8 bolts.
|
Install in this Direction |
Torque:
43 N·m {438 kgf·cm, 32 ft·lbf}
|
(b) Engage the 4 clamps. |
|
(c) Install the headlight assembly LH.
Click here
![2019 - 2022 MY Avalon Avalon HV [04/2018 - ]; LIGHTING (EXT): HEADLIGHT ASSEMBLY: INSTALLATION+](/t3Portal/stylegraphics/info.gif)
(d) Install the headlight assembly RH.
HINT:
Use the same procedure as for the LH side.
2. INSTALL FRONT BUMPER ENERGY ABSORBER
(a) Engage the 2 guides to install the front bumper energy absorber as shown in the illustration.
|
|
Install in this Direction |
3. INSTALL NO. 2 FRONT BUMPER ENERGY ABSORBER
(a) Engage the 4 guides to install the No. 2 front bumper energy absorber as shown in the illustration.
|
|
Install in this Direction |
4. INSTALL FRONT BUMPER SIDE RETAINER LH
(a) Engage the claw to temporarily install the front bumper side retainer LH as shown in the illustration.
|
|
Install in this Direction (1) |
|
Install in this Direction (2) |
(b) Engage the clip as shown in the illustration.
(c) Install the front bumper side retainer LH with the bolt (A) and bolt (B).
|
Bolt (A) |
|
Bolt (B) |
Torque:
5.4 N·m {55 kgf·cm, 48 in·lbf}
5. INSTALL FRONT BUMPER SIDE RETAINER RH
HINT:
Use the same procedure as for the LH side.
6. INSTALL FRONT BUMPER MOULDING (for Bar Type Radiator Grille)
(a) Engage the 20 guides and 18 claws.
|
(b) Install the front bumper moulding with the 6 screws. |
|
7. INSTALL RADIATOR GRILLE (for Bar Type Radiator Grille)
|
(a) Engage the 6 guides and 6 claws. |
|
|
(b) Install the radiator grille with the screw. |
|
8. INSTALL LOWER RADIATOR GRILLE SUB-ASSEMBLY (for Bar Type Radiator Grille)
(a) Engage the 5 guides and 23 claws.
|
(b) Install the lower radiator grille sub-assembly with the 8 screws. |
|
9. INSTALL LOWER RADIATOR GRILLE SUB-ASSEMBLY (for Mesh Type Radiator Grille)
(a) Engage the 3 guides and 23 claws.
|
(b) Install the lower radiator grille sub-assembly with the 8 screws. |
|
10. INSTALL RADIATOR GRILLE SUB-ASSEMBLY
|
(a) Engage the guide and 4 claws. |
|
|
(b) Install the 8 screws. |
|
(c) Install the radiator grille sub-assembly with the 2 clips and 3 screws.
|
|
Screw |
|
|
Clip |
11. INSTALL RADIATOR GRILLE EMBLEM ASSEMBLY
|
(a) Engage the 2 claws. |
|
(b) Install the radiator grille emblem assembly with the 2 screws.
12. INSTALL HOOD TO FRONT END PANEL SEAL
HINT:
When installing the hood to front end panel seal, heat the front bumper cover using a heat light.
Heating Temperature
|
Item |
Temperature |
|---|---|
|
Front Bumper Cover |
20 to 30°C (68 to 86°F) |
CAUTION:
- Do not touch the heat light and heated parts, touching the heat light may result in burns.
- Touching heated parts for a long time may result in burns.
|
*a |
Heated Part |
|
*b |
Heat Light |
NOTICE:
Do not heat the front bumper cover excessively.
(a) Clean the front bumper cover surface.
(1) Using a heat light, heat the front bumper cover surface.
(2) Remove any remaining double-sided tape from the front bumper cover.
(3) Wipe off any tape adhesive residue with cleaner.
(b) Remove the release paper from a new hood to front end panel seal.
HINT:
After removing the release paper, keep the exposed adhesive free from foreign matter.
(c) Attach the double-sided tape as shown in the illustration.
|
Double-sided Tape |
HINT:
Press the hood to front end panel seal firmly to install it.
(d) Engage the 4 clips to install the hood to front end panel seal.
13. INSTALL MILLIMETER WAVE RADAR SENSOR ASSEMBLY
Click here
14. INSTALL AIR INTAKE DUCT LH
(a) Engage the 4 guides as shown in the illustration.
|
|
Install in this Direction (1) |
|
|
Install in this Direction (2) |
(b) Install the air intake duct LH with the clip and 2 screws.
|
|
Screw |
|
|
Clip |
15. INSTALL AIR INTAKE DUCT RH
HINT:
Use the same procedure as for the LH side.
16. INSTALL FRONT LICENSE PLATE BRACKET SUB-ASSEMBLY (for Bar Type Radiator Grille)
(a) Temporarily install the front license plate bracket sub-assembly as shown in the illustration.
|
|
Install in this Direction |
|
(b) Install the front license plate bracket sub-assembly with the 4 screws. |
|
17. INSTALL FRONT LICENSE PLATE BRACKET SUB-ASSEMBLY (for Mesh Type Radiator Grille)
(a) Temporarily install the front license plate bracket sub-assembly as shown in the illustration.
|
|
Install in this Direction |
|
(b) Install the front license plate bracket sub-assembly with the 4 screws. |
|
18. INSTALL NO. 4 ENGINE ROOM WIRE (w/ Intuitive Parking Assist System)
(a) Engage the 11 clamps to install the No. 4 engine room wire.
19. INSTALL FRONT CORNER ULTRASONIC SENSOR (w/ Intuitive Parking Assist System)
Click here
HINT:
Use the same procedure for the RH side and LH side.
20. INSTALL FRONT CENTER ULTRASONIC SENSOR (w/ Intuitive Parking Assist System)
Click here
HINT:
Use the same procedure for the RH side and LH side.
21. INSTALL FRONT TELEVISION CAMERA ASSEMBLY (w/ Panoramic View Monitor System)
Click here
|
|