Last Modified: 08-21-2023 6.11:8.1.0 Doc ID: RM100000001ANJM
Model Year Start: 2019 Model: Avalon HV Prod Date Range: [04/2018 -           ]
Title: BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model): C1242; Open Circuit in IG1/IG2 Power Source Circuit; 2019 - 2022 MY Avalon HV [04/2018 -        ]

DTC

C1242

Open Circuit in IG1/IG2 Power Source Circuit

DESCRIPTION

Refer to DTC C1241.

Click here 2019 - 2020 MY Avalon HV [04/2018 - 08/2020]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model): C1241; Low or High Power Supply Voltage 2021 - 2022 MY Avalon HV [08/2020 -        ]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model): C1241; Low or High Power Supply Voltage

DTC No.

Detection Item

INF Code

DTC Detection Condition

Trouble Area

MIL

Note

C1242

Open Circuit in IG1/IG2 Power Source Circuit

111

112
  • INF Code: 111
    • When the IG1 terminal voltage is less than 3.5 V, the IG2 terminal voltage is 9.5 V or more for 4 seconds or more.
  • INF Code: 112
    • When communication with the hybrid vehicle control ECU is normal or the vehicle speed is 10 km/h (6 mph) or more, and the IG1 terminal voltage is 9.5 V or more, the IG2 terminal voltage is less than 3.5 V for 4 seconds or more.
  • INF Code: 111
    • Open or short in IG1 circuit
    • Improperly connected connector, deformation or corrosion of terminals
    • Smart key system (IG start circuit)
    • Auxiliary battery
    • Hybrid control system (Charging circuit)
    • Skid control ECU (brake booster with master cylinder assembly)
  • INF Code: 112
    • Open or short in IG2 circuit
    • Improperly connected connector, deformation or corrosion of terminals
    • Smart key system (IG start circuit)
    • Auxiliary battery
    • Hybrid control system (Charging circuit)
    • Skid control ECU (brake booster with master cylinder assembly)

Comes on
  • INF Code 111: SAE Code C123B
  • INF Code 112: SAE Code C123E
  • Electronically controlled brake system DTC

MONITOR DESCRIPTION

  • During normal operation, the voltage at IG1 and IG2 change mutually; however, if the voltages do not change mutually such as when IG1 is on and IG2 is off or when IG1 is off and IG2 is on, the skid control ECU (brake booster with master cylinder assembly) judges that there is an open in the IG1 or IG2 circuit and illuminates the MIL and stores a DTC.

MONITOR STRATEGY

Related DTCs

C123B: IG1 circuit low

C123E: IG2 circuit low

Required Sensors/Components(Main)

Skid control ECU (brake booster with master cylinder assembly)

Required Sensors/Components(Related)

Speed sensor

Skid control ECU (brake booster with master cylinder assembly)

Frequency of Operation

Continuous

Duration

4 seconds

MIL Operation

Immediately

Sequence of Operation

None

TYPICAL ENABLING CONDITIONS

C123B

Monitor runs whenever the following DTCs are not stored

None

IG2 voltage

Higher than 9.5 V

C123E

Monitor runs whenever the following DTCs are not stored

None

Both of the following conditions are met

A and B

A. IG1 voltage

Higher than 9.5 V

B. Either of the following condition is met

-

Vehicle speed

Higher than 10 km/h (6 mph)

Communication status with hybrid control system

Valid

TYPICAL MALFUNCTION THRESHOLDS

C123B

IG1

Off

C123E

IG2

Off

COMPONENT OPERATING RANGE

C123B

Both of the following conditions are met

-

IG2 voltage

Higher than 9.5 V

IG1

On

C123E

Both of the following conditions are met

-

IG1 voltage

Higher than 9.5 V

IG2

On

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the power switch on (IG).
  3. Turn the Techstream on.
  4. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  5. Turn the power switch off.
  6. Turn the power switch on (READY).
  7. Turn the Techstream on.
  8. Drive the vehicle at 10 km/h (6 mph) or more for 4 seconds or more.
  9. Enter the following menus: Chassis / ABS/VSC/TRAC / Trouble Codes.
  10. Read the DTCs.

    HINT:

    • If a DTC is output, the system is malfunctioning.
    • If a DTC is not output, perform the following procedure.
  11. If the DTCs are not output, perform a universal trip and check for permanent DTCs.

    Click here 2019 - 2022 MY Avalon HV [04/2018 -        ]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model): DTC CHECK / CLEAR

    HINT:

    • If a permanent DTC is output, the system is malfunctioning.
    • If no permanent DTCs are output, the system is normal.

WIRING DIAGRAM

Refer to DTC C1241.

Click here 2019 - 2020 MY Avalon HV [04/2018 - 08/2020]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model): C1241; Low or High Power Supply Voltage 2021 - 2022 MY Avalon HV [08/2020 -        ]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model): C1241; Low or High Power Supply Voltage

CAUTION / NOTICE / HINT

NOTICE:

  • After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

    Click here 2019 - 2021 MY Avalon HV [04/2018 - 08/2021]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model): INITIALIZATION 2022 MY Avalon HV [08/2021 -        ]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model): INITIALIZATION

  • Inspect the fuses for circuits related to this system before performing the following procedure.

PROCEDURE

1.

CHECK FREEZE FRAME DATA

(a) Check the INF code from the Freeze Frame Data stored when DTC (C1242) was stored.

Click here 2019 - 2022 MY Avalon HV [04/2018 -        ]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model): FREEZE FRAME DATA

Chassis > ABS/VSC/TRAC > Trouble Codes

Result

Proceed to

INF code 111 is output.

A

INF code 112 is output.

B
B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY 2019 - 2021 MY Avalon HV [04/2018 - 08/2021]; BRAKE SYSTEM (OTHER): BRAKE BOOSTER (for HV Model): REMOVAL 2022 MY Avalon HV [08/2021 -        ]; BRAKE SYSTEM (OTHER): BRAKE BOOSTER (for HV Model): REMOVAL

A

2.

CHECK HARNESS AND CONNECTOR (IG1 AND IG2 TERMINAL)

(a) Turn the power switch off.

*a

Front view of wire harness connector

(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))

(b) Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.

(c) Disconnect the A35 skid control ECU (brake booster with master cylinder assembly) connector.

(d) Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.

(e) Turn the power switch on (IG).

(f) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

A35-23 (IG1) - Body ground

Power switch on (IG)

11 to 14 V

A35-9 (IG2) - Body ground

Power switch on (IG)

11 to 14 V

Result

Proceed to

11 to 14 V.

A

Below 11 V.

B
A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY 2019 - 2021 MY Avalon HV [04/2018 - 08/2021]; BRAKE SYSTEM (OTHER): BRAKE BOOSTER (for HV Model): REMOVAL 2022 MY Avalon HV [08/2021 -        ]; BRAKE SYSTEM (OTHER): BRAKE BOOSTER (for HV Model): REMOVAL

B

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 AND/OR IG2 CIRCUIT)