Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM100000001XX36
Model Year Start: 2022 Model: Camry HV Prod Date Range: [08/2021 -           ]
Title: POWER OUTLETS (INT): WIRELESS CHARGING SYSTEM: Status Signal Circuit; 2022 - 2024 MY Camry HV [08/2021 -        ]

Status Signal Circuit

DESCRIPTION

This circuit sends a charging suspension signal from the certification ECU (smart key ECU assembly) to the mobile wireless charger cradle assembly (front console box insert sub-assembly). Based on this signal, the mobile wireless charger cradle assembly (front console box insert sub-assembly) suspends or resumes wireless charging.

HINT:

The wireless charging system uses the same radio wave frequency that is used to perform verification of the electrical key transmitter sub-assembly. Therefore, when the electrical key transmitter sub-assembly verification is being performed, the certification ECU (smart key ECU assembly) sends a charging suspension signal to the wireless charging system to suspend charging.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Before replacing the certification ECU (smart key ECU assembly), refer to Registration.

Click here 2020 - 2022 MY Camry HV [09/2019 - 08/2022]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function): REGISTRATION 2023 - 2024 MY Camry HV [08/2022 -        ]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function): REGISTRATION

PROCEDURE

1.

CHECK MOBILE WIRELESS CHARGER CRADLE ASSEMBLY (FRONT CONSOLE BOX INSERT SUB-ASSEMBLY) (DIS TERMINAL)

*a

Component with harness connected

(Mobile Wireless Charger Cradle Assembly (Front Console Box Insert Sub-assembly))

(a) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

k2-8 (DIS) - Body ground

For 5 seconds after turning power switch from off to on (ACC)*1

4.5 to 6.0 V

Device being charged

Below 1 V

Charging suspended due to smart key system status*2

4.5 to 6.0 V
  • *1: When the power switch is turned from off to on (ACC), the mobile wireless charger cradle assembly (front console box insert sub-assembly) monitors the charging suspension signal for 5 seconds. If the charging suspension signal is not 4 V or more for 0.8 seconds or more during monitoring, the mobile wireless charger cradle assembly (front console box insert sub-assembly) determines that there is an open in the charging suspension signal line, blinks (pattern 1) the indicator light (amber), and prohibits operation until the power switch is turned from off to on (ACC) again.
  • *2: For details about conditions when the certification ECU (smart key ECU assembly) sends the charging suspension signal, refer to System Description.

    Click here 2022 - 2024 MY Camry HV [08/2021 -        ]; POWER OUTLETS (INT): WIRELESS CHARGING SYSTEM: SYSTEM DESCRIPTION

OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.

CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - MOBILE WIRELESS CHARGER CRADLE ASSEMBLY (FRONT CONSOLE BOX INSERT SUB-ASSEMBLY))

(a) Disconnect the R8 certification ECU (smart key ECU assembly) connector.

(b) Disconnect the k1 mobile wireless charger cradle assembly (front console box insert sub-assembly) connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

R8-7 (WCSW) - k2-8 (DIS)

Always

Below 1 Ω

R8-7 (WCSW) or k2-8 (DIS) - Body ground

Always

10 kΩ or higher
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR