| Last Modified: 11-20-2023 | 6.11:8.1.0 | Doc ID: RM100000001WMXI |
| Model Year Start: 2021 | Model: Camry HV | Prod Date Range: [10/2020 - ] |
| Title: PARKING BRAKE: ELECTRIC PARKING BRAKE SYSTEM: C061014; Right Electric Parking Brake Actuator Control Circuit Short to Ground or Open; 2021 - 2024 MY Camry HV [10/2020 - ] | ||
|
DTC |
C061014 |
Right Electric Parking Brake Actuator Control Circuit Short to Ground or Open |
DESCRIPTION
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
Memory |
Note |
|---|---|---|---|---|---|
|
C061014 |
Right Electric Parking Brake Actuator Control Circuit Short to Ground or Open |
|
|
DTC stored |
An electric parking brake system malfunction is displayed on the combination meter assembly. |
WIRING DIAGRAM
Click here
![2021 - 2024 MY Camry HV [10/2020 - ]; PARKING BRAKE: ELECTRIC PARKING BRAKE SYSTEM: C061011; Right Electric Parking Brake Actuator Control Circuit Short to Ground+](/t3Portal/stylegraphics/info.gif)
PROCEDURE
|
1. |
INSPECT NO. 1 PARKING BRAKE WIRE ASSEMBLY |
(a) Make sure that there is no looseness at the locking part and the connecting part of the connectors.
OK:
The connector is securely connected.
(b) Disconnect the uR2 and u1 No. 1 parking brake wire assembly connectors.
(c) Check both the connector case and the terminals for deformation and corrosion.
OK:
No deformation or corrosion.
(d) Measure the resistance according to the value(s) in the table below.
|
*a |
Front view of No. 1 Parking Brake Wire Assembly |
*b |
(to wire harness connector) |
|
*c |
(to Parking Brake Actuator Assembly RH) |
- |
- |
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
uR2-2 - u1-2 (RE+) |
Always |
Below 1 Ω |
|
uR2-2 or u1-2 (RE+) - Body ground and other terminals |
Always |
10 kΩ or higher |
|
uR2-1 - u1-1 (RE-) |
Always |
Below 1 Ω |
|
uR2-1 or u1-1 (RE-) - Body ground and other terminals |
Always |
10 kΩ or higher |
| NG |
|
REPLACE NO. 1 PARKING BRAKE WIRE ASSEMBLY |
|
|
2. |
CHECK HARNESS AND CONNECTOR (PARKING BRAKE ECU (BRAKE ACTUATOR ASSEMBLY) - PARKING BRAKE ACTUATOR ASSEMBLY RH) |
(a) Make sure the No. 1 parking brake wire assembly is securely installed.
(b) Disconnect the A44 parking brake ECU (brake actuator assembly) connector.
(c) Disconnect the u1 parking brake actuator assembly RH connector.
(d) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
A44-4 (MRR+) - u1-2 (RE+) |
Always |
Below 1 Ω |
|
A44-4 (MRR+) or u1-2 (RE+) - Body ground |
Always |
10 kΩ or higher |
|
A44-3 (MRR-) - u1-1 (RE-) |
Always |
Below 1 Ω |
|
A44-3 (MRR-) or u1-1 (RE-) - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
3. |
INSPECT PARKING BRAKE ACTUATOR ASSEMBLY RH |
Click here
| OK |
|
| NG |
|
|
|