Last Modified: 11-20-2023 |
6.11:8.1.0 |
Doc ID: RM100000001TG4A |
Model Year Start: 2021 |
Model: Camry HV |
Prod Date Range: [10/2020 -
] |
Title: SEAT BELT: REAR SEAT OUTER BELT ASSEMBLY: REMOVAL; 2021 - 2024 MY Camry HV [10/2020 - ] |
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during rear seat outer belt assembly removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure
|
Necessary Procedure
|
Effect/Inoperative Function when Necessary Procedure not Performed
|
Link
|
Disconnect cable from negative auxiliary battery terminal
|
Perform steering sensor zero point calibration
|
Lane Tracing Assist System
|
|
Pre-collision System
|
Lighting System (w/ AFS)(EXT)
|
Memorize steering angle neutral point
|
Parking Assist Monitor System
|
|
Panoramic View Monitor System
|
|
CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.
Click here
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here
2. REMOVE LUGGAGE TRIM SERVICE HOLE COVER
Click here
3. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
Click here
CAUTION:
-
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
-
If an SRS part is accidentally deployed, it may cause a serious injury.
4. REMOVE REAR SEAT CUSHION ASSEMBLY
Click here
5. REMOVE REAR SEAT CUSHION LOCK HOOK
Click here
6. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH
Click here
7. REMOVE REAR SIDE SEATBACK ASSEMBLY LH
Click here
8. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH
HINT:
Use the same procedure as for the LH side.
9. REMOVE REAR SIDE SEATBACK ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
10. REMOVE INNER ROOF SIDE GARNISH LH
Click here
11. REMOVE INNER ROOF SIDE GARNISH RH
HINT:
Use the same procedure as for the LH side.
12. DISCONNECT REAR SEAT OUTER BELT ASSEMBLY LH
(a) Remove the bolt to disconnect the floor anchor of the rear seat outer belt assembly LH.
|
|
13. DISCONNECT REAR SEAT OUTER BELT ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
14. REMOVE CENTER STOP LIGHT SET
Click here
15. REMOVE REAR SEAT SHOULDER BELT HOLE COVER
(a) Disengage the 2 claws and 2 guides to remove the rear seat shoulder belt hole cover.
HINT:
Use the same procedure for the other rear seat shoulder belt hole covers.
|
|
16. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY
(a) Fold the rear seatback assembly LH and rear seatback assembly RH forward.
(c) Disengage the 3 clips and 5 guides.
|
|
(d) Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly then remove the package tray trim panel assembly.
17. REMOVE REAR SEAT OUTER BELT ASSEMBLY LH
(a) Using a screwdriver, pull out the locking button as shown in the illustration to release the lock and disconnect the pretensioner connector.
HINT:
Tape the screwdriver tip before use.
|
|
*a
|
Protective Tape
|
*b
|
Locking Button
|
*c
|
Release
|
|
|
(c) Disengage the guide to remove the rear seat outer belt assembly LH.
18. REMOVE REAR SEAT OUTER BELT ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
19. REMOVE REAR SEAT BELT RETRACTOR COVER
(a) Remove the rear seat belt retractor cover as shown in the illustration.
HINT:
Use the same procedure for the RH side and LH side.
|
Remove in this Direction
|
|