| Last Modified: 11-20-2023 | 6.11:8.1.0 | Doc ID: RM100000001T5IM |
| Model Year Start: 2021 | Model: Camry HV | Prod Date Range: [10/2020 - ] |
| Title: PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM: DATA LIST / ACTIVE TEST; 2021 - 2024 MY Camry HV [10/2020 - ] | ||
DATA LIST / ACTIVE TEST
DATA LIST
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Chassis / Circumference Monitoring Camera Control Module / Data List.
(e) Read the Data List according to the display on the Techstream.
Chassis > Panoramic View Monitor > Data List
|
Tester Display |
Measurement Item |
Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
Main CPU Forced Termination Detection Record |
A history item indicating that the main CPU did not enter standby status within 15 seconds of turning the ignition switch off and a forced end was applied |
Unrec/Rec |
Unrec: Television camera controller is normal Rec: Television camera controller is abnormal |
- |
|
Main CPU Abnormal Response Record |
A history item indicating that the main CPU became unresponsive in normal status |
Unrec/Rec |
Unrec: Television camera controller is normal Rec: Television camera controller is abnormal |
- |
|
Main CPU Abnormal Reset Record |
A history item indicating that the main CPU was reset, although the ignition switch was not turned off in normal status |
Unrec/Rec |
Unrec: Television camera controller is normal Rec: Television camera controller is abnormal |
- |
|
Image Processing IC Written Protect Record |
A history item indicating that the image processing IC memory was write protected |
Unrec/Rec |
Unrec: Television camera controller is normal Rec: Television camera controller is abnormal |
- |
|
Image Processing IC Initialized Malfunction Record |
A history item indicating that the image processing IC memory was not initialized |
Unrec/Rec |
Unrec: Television camera controller is normal Rec: Television camera controller is abnormal |
- |
|
Main EEPROM Access Status |
Main EEPROM access status |
OK/NG |
OK: Television camera controller is normal NG: Television camera controller is abnormal |
- |
|
Sub EEPROM Access Status |
Sub-EEPROM access status |
OK/NG |
OK: Television camera controller is normal NG: Television camera controller is abnormal |
- |
|
System Power Supply Voltage Malfunction Record |
A history item indicating an abnormally generated-voltage value from the system power source |
Unrec/Rec |
Unrec: Television camera controller is normal Rec: Television camera controller is abnormal |
- |
|
Main CPU Starting Malfunction Record |
A history item indicating that the main CPU did not start |
Unrec/Rec |
Unrec: Television camera controller is normal Rec: Television camera controller is abnormal |
- |
|
CAN CPU Boot Malfunction Record |
A history item indicating that the CPU controlling the input and output of the information obtained via the CAN communication system did not start and the information could not be retrieved |
Unrec/Rec |
Unrec: Television camera controller is normal Rec: Television camera controller is abnormal |
- |
|
Wheel Speed Sensor (4wheel) |
Reception state of the vehicle speed signal from the skid control ECU |
OK/NG |
OK: Speed signal received NG: Speed signal not received |
- |
|
Continuous Bus Off |
Continuous bus off status (Global) |
Not Detected/Detected |
Not detected: Communication condition available Detected: Communication condition not available |
- |
|
Image Adjustment Status |
Status of the image adjustment status |
Incomplete/Processing/Complete |
Incomplete: Image adjustment incomplete Processing: Image adjustment in processing Complete: Image adjustment completed |
- |
|
Number of DTC |
Number of DTCs (past and present) |
Min: 0, Max: 255 |
Number of DTCs will be displayed |
- |
|
|