Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM100000001T5IE
Model Year Start: 2021 Model: Camry HV Prod Date Range: [10/2020 -           ]
Title: METER / GAUGE / DISPLAY: COMBINATION METER: REMOVAL; 2021 - 2024 MY Camry HV [10/2020 -        ]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during combination meter assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

Disconnect cable from negative (-) auxiliary battery terminal

Perform steering sensor zero point calibration

Lane Tracing Assist System

2021 - 2024 MY Camry HV [10/2020 -        ]; PRE-COLLISION: PRE-COLLISION SYSTEM: INITIALIZATION

Pre-collision system

Lighting system (w/ AFS)(EXT)

Memorize steering angle neutral point

Parking assist monitor system

2018 - 2024 MY Camry HV [07/2017 -        ]; PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM: INITIALIZATION

Panoramic view monitor system

2021 - 2024 MY Camry HV [10/2020 -        ]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM: INITIALIZATION

PROCEDURE

1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click here 2020 - 2024 MY Camry HV [09/2019 -        ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION

2. REMOVE LUGGAGE TRIM SERVICE HOLE COVER

Click here 2021 - 2024 MY Camry HV [10/2020 -        ]; MAINTENANCE: AUXILIARY BATTERY: REMOVAL+

3. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Click here 2021 - 2024 MY Camry HV [10/2020 -        ]; MAINTENANCE: AUXILIARY BATTERY: REMOVAL+

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click here 2021 - 2022 MY Camry HV [10/2020 - 08/2022]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION 2023 - 2024 MY Camry HV [08/2022 -        ]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION

4. REMOVE NO. 1 METER HOOD CLUSTER

Click here 2018 - 2024 MY Camry HV [07/2017 -        ]; INTERIOR PANELS / TRIM: FRONT CONSOLE BOX: REMOVAL+

5. REMOVE NO. 2 METER HOOD CLUSTER

Click here 2021 - 2024 MY Camry HV [10/2020 -        ]; INTERIOR PANELS / TRIM: INSTRUMENT PANEL SAFETY PAD: REMOVAL+

6. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY

(a) Operate the tilt and telescopic lever to fully extend and lower the steering column assembly.

(b) Apply protective tape to the area shown in the illustration.

Protective Tape

(c) Apply protective tape to the area shown in the illustration.

Protective Tape

(d) Disengage the 2 claws and 4 clips to separate the instrument cluster finish panel assembly.

Remove in this Direction

(e) Remove the 2 clips.

(f) Disengage the 2 clips as shown in the illustration.

Place Hand Here

Remove in this Direction

(g) Disengage the 2 clips as shown in the illustration.

Place Hand Here

Remove in this Direction

(h) Disengage the 2 guides as shown in the illustration.

Remove in this Direction

(i) Disconnect the connector to remove the instrument cluster finish panel assembly.

7. REMOVE COMBINATION METER ASSEMBLY

(a) Remove the 3 screws.

(b) Disengage the 2 clips as shown in the illustration.

Remove in this Direction

(c) Disengage the clamp.

(d) Disconnect each connector to remove the combination meter assembly.