| Last Modified: 11-20-2023 | 6.11:8.1.0 | Doc ID: RM100000001T5GT |
| Model Year Start: 2021 | Model: Camry HV | Prod Date Range: [10/2020 - ] |
| Title: PARK ASSIST / MONITORING: INTUITIVE PARKING ASSIST SYSTEM: C1AE687; Ultrasonic Sensor (Rear Left Corner) Missing Message; 2021 - 2024 MY Camry HV [10/2020 - ] | ||
|
DTC |
C1AE687 |
Ultrasonic Sensor (Rear Left Corner) Missing Message |
DESCRIPTION
This DTC is output when an open circuit or short occurs in the communication line between as rear corner ultrasonic sensor LH and the rear center ultrasonic sensor LH, or when a malfunction occurs in a rear corner ultrasonic sensor LH.
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
|---|---|---|---|
|
C1AE687 |
Ultrasonic Sensor (Rear Left Corner) Missing Message |
Rear corner ultrasonic sensor LH lost communication |
|
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
-
Perform registration after replacing or removing and installing the ultrasonic sensor or clearance warning ECU assembly.
Click here
![2021 - 2024 MY Camry HV [10/2020 - ]; PARK ASSIST / MONITORING: INTUITIVE PARKING ASSIST SYSTEM: CALIBRATION](/t3Portal/stylegraphics/info.gif)
-
If a DTC is detected again after the repair, turn the ignition switch to ON and turn the intuitive parking assist system on, and then clear the DTC.
Click here
-
If C1AE796 is output at the same time, check C1AE796 first.
Click here
PROCEDURE
|
1. |
VEHICLE CONDITION AND WORK DETAILS CHECK |
(a) Check the vehicle condition and work details.
|
Result |
Proceed to |
|---|---|
|
The clearance warning ECU assembly or ultrasonic sensor has not been replaced |
A |
|
The clearance warning ECU assembly or ultrasonic sensor has been replaced |
B |
| B |
|
|
|
2. |
CHECK CONNECTOR CONNECTION CONDITION (ULTRASONIC SENSOR) |
(a) Check that the connector is properly connected to the rear corner ultrasonic sensor and rear center ultrasonic sensor.
|
|
3. |
CHECK FOR DTC |
(a) According to the display on the GTS, check for DTCs.
Body Electrical > Clearance Warning > Trouble Codes
(b) According to the display on the GTS, clear the DTCs.
Body Electrical > Clearance Warning > Clear DTCs
(c) Recheck for DTCs.
Body Electrical > Clearance Warning > Trouble Codes
|
Result |
Proceed to |
|---|---|
|
C1AE687 is not output |
A |
|
C1AE687 is output |
B |
| A |
|
END (CONNECTOR CONNECTION MALFUNCTION) |
|
|
4. |
CHECK CONNECTOR CONNECTION CONDITION (CLEARANCE WARNING ECU ASSEMBLY) |
(a) Check that the connector is properly connected to the clearance warning ECU assembly.
|
|
5. |
CHECK FOR DTC |
(a) According to the display on the GTS, check for DTCs.
Body Electrical > Clearance Warning > Trouble Codes
(b) According to the display on the GTS, clear the DTCs.
Body Electrical > Clearance Warning > Clear DTCs
(c) Recheck for DTCs.
Body Electrical > Clearance Warning > Trouble Codes
DTC OUTPUT COMBINATION:
|
Symptoms |
DTC Detection |
|||
|---|---|---|---|---|
|
C1AE987 |
C1AE887 |
C1AE787 |
C1AE687 |
|
|
Symptom 1 |
Not output |
Not output |
Not output |
Not output |
|
Symptom 2 |
Output |
Output |
Output |
Output |
|
Symptom 3 |
Not output |
Output |
Output |
Output |
|
Symptom 4 |
Not output |
Not output |
Output |
Output |
|
Symptom 5 |
Not output |
Not output |
Not output |
Output |
|
Result |
Proceed to |
|---|---|
|
Listed under symptom 1 in combination table |
A |
|
Listed under symptom 2 in combination table |
B |
|
Listed under symptom 3 in combination table |
C |
|
Listed under symptom 4 in combination table |
D |
|
Listed under symptom 5 in combination table |
E |
| A |
|
USE SIMULATION METHOD TO CHECK
|
| B |
|
GO TO CORRESPONDING FLOWCHART (INTUITIVE PARKING ASSIST SYSTEM (C1AE987)) |
| C |
|
GO TO CORRESPONDING FLOWCHART (INTUITIVE PARKING ASSIST SYSTEM (C1AE887)) |
| D |
|
GO TO CORRESPONDING FLOWCHART (INTUITIVE PARKING ASSIST SYSTEM (C1AE787)) |
|
|
6. |
CHECK WIRE HARNESS AND CONNECTOR (REAR CENTER ULTRASONIC SENSOR LH - REAR CORNER ULTRASONIC SENSOR LH) |
(a) Disconnect the X7 rear center ultrasonic sensor LH connector.
(b) Disconnect the X8 rear corner ultrasonic sensor LH connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
X7-1 (BO) - X8-4 (BI) |
Always |
Below 1 Ω |
|
X7-2 (SO) - X8-5 (SI) |
Always |
Below 1 Ω |
|
X7-3 (EO) - X8-6 (EI) |
Always |
Below 1 Ω |
|
X7-1 (BO) or X8-4 (BI) - Body ground |
Always |
10 kΩ or higher |
|
X7-2 (SO) or X8-5 (SI) - Body ground |
Always |
10 kΩ or higher |
|
X7-3 (EO) or X8-6 (EI) - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE WIRE HARNESS OR CONNECTOR |
|
|
7. |
REPLACE REAR CORNER ULTRASONIC SENSOR LH |
(a) Replace the rear corner ultrasonic sensor LH with a new or normally functioning one.
Click here
HINT:
To check if the ultrasonic sensor is functioning correctly, replace it with another ultrasonic sensor.
|
|
8. |
CHECK FOR DTC |
(a) According to the display on the GTS, check for DTCs.
Body Electrical > Clearance Warning > Trouble Codes
(b) According to the display on the GTS, clear the DTCs.
Body Electrical > Clearance Warning > Clear DTCs
(c) Recheck for DTCs.
Body Electrical > Clearance Warning > Trouble Codes
|
Result |
Proceed to |
|---|---|
|
No DTC is output |
A |
|
"C1AE687" is output |
B |
| A |
|
END (REAR CORNER ULTRASONIC SENSOR LH WAS DEFECTIVE) |
| B |
|
|
|