Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM100000001T5GP
Model Year Start: 2021 Model: Camry HV Prod Date Range: [10/2020 -           ]
Title: PARK ASSIST / MONITORING: INTUITIVE PARKING ASSIST SYSTEM: C1AE387; Ultrasonic Sensor (Front Right Center) Missing Message; 2021 - 2024 MY Camry HV [10/2020 -        ]

DTC

C1AE387

Ultrasonic Sensor (Front Right Center) Missing Message

DESCRIPTION

This DTC is stored when an open circuit or short occurs in the communication line between the front center ultrasonic sensor RH and the front corner ultrasonic sensor RH, or when a malfunction occurs in the front center ultrasonic sensor RH.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

C1AE387

Ultrasonic Sensor (Front Right Center) Missing Message

Front center ultrasonic sensor RH lost communication

  • Front center ultrasonic sensor RH
  • Harness or connector
  • Clearance warning ECU assembly

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

  • Perform registration after replacing or removing and installing the ultrasonic sensor or clearance warning ECU assembly.

    Click here 2021 - 2024 MY Camry HV [10/2020 -        ]; PARK ASSIST / MONITORING: INTUITIVE PARKING ASSIST SYSTEM: CALIBRATION

  • If a DTC is detected again after the repair, turn the ignition switch to ON and turn the intuitive parking assist system on, and then clear the DTC.

    Click here 2021 - 2024 MY Camry HV [10/2020 -        ]; PARK ASSIST / MONITORING: INTUITIVE PARKING ASSIST SYSTEM: DTC CHECK / CLEAR

  • If C1AE496 is output at the same time, check C1AE496 first.

    Click here 2021 - 2024 MY Camry HV [10/2020 -        ]; PARK ASSIST / MONITORING: INTUITIVE PARKING ASSIST SYSTEM: C1AE496; Ultrasonic Sensor (Front Right Corner) Component Internal Failure

PROCEDURE

1.

VEHICLE CONDITION AND WORK DETAILS CHECK

(a) Check the vehicle condition and work details.

Result

Proceed to

The clearance warning ECU assembly or ultrasonic sensor has not been replaced

A

The clearance warning ECU assembly or ultrasonic sensor has been replaced

B

B

GO TO CALIBRATION

A

2.

CHECK CONNECTOR CONNECTION CONDITION (ULTRASONIC SENSOR)

(a) Check that the connector is properly connected to the front corner ultrasonic sensor and front center ultrasonic sensor.

NEXT

3.

CHECK FOR DTC

(a) According to the display on the GTS, check for DTCs.

Body Electrical > Clearance Warning > Trouble Codes

(b) According to the display on the GTS, clear the DTCs.

Body Electrical > Clearance Warning > Clear DTCs

(c) Recheck for DTCs.

Body Electrical > Clearance Warning > Trouble Codes

Result

Proceed to

C1AE387 is not output

A

C1AE387 is output

B

A

END (CONNECTOR CONNECTION MALFUNCTION)

B

4.

CHECK CONNECTOR CONNECTION CONDITION (CLEARANCE WARNING ECU ASSEMBLY)

(a) Check that the connector is properly connected to the clearance warning ECU assembly.

NEXT

5.

CHECK FOR DTC

(a) According to the display on the GTS, check for DTCs.

Body Electrical > Clearance Warning > Trouble Codes

(b) According to the display on the GTS, clear the DTCs.

Body Electrical > Clearance Warning > Clear DTCs

(c) Recheck for DTCs.

Body Electrical > Clearance Warning > Trouble Codes

DTC OUTPUT COMBINATION:

Symptoms

DTC Detection

C1AE487

C1AE387

C1AE287

C1AE187

Symptom 1

Not output

Not output

Not output

Not output

Symptom 2

Output

Output

Output

Output

Symptom 3

Not output

Output

Output

Output

Symptom 4

Not output

Not output

Output

Output

Symptom 5

Not output

Not output

Not output

Output

Symptom 6

Not output

Output

Not output

Not output

Result

Proceed to

Listed under symptom 1 in combination table

A

Listed under symptom 2 in combination table

B

Listed under symptom 3 in combination table

C

Listed under symptom 4 in combination table

D

Listed under symptom 5 in combination table

E

Listed under symptom 6 in combination table

F

A

USE SIMULATION METHOD TO CHECK 2021 MY Camry HV [10/2020 - 08/2021]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING 2022 - 2024 MY Camry HV [08/2021 -        ]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING

B

GO TO CORRESPONDING FLOWCHART (INTUITIVE PARKING ASSIST SYSTEM (C1AE487))

D

GO TO CORRESPONDING FLOWCHART (INTUITIVE PARKING ASSIST SYSTEM (C1AE287))

E

GO TO CORRESPONDING FLOWCHART (INTUITIVE PARKING ASSIST SYSTEM (C1AE187))

F

GO TO STEP 7

C

6.

CHECK WIRE HARNESS AND CONNECTOR (FRONT CORNER ULTRASONIC SENSOR RH - FRONT CENTER ULTRASONIC SENSOR RH)

(a) Disconnect the B8 front corner ultrasonic sensor RH connector.

(b) Disconnect the B9 front center ultrasonic sensor RH connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

B8-1 (BO) - B9-4 (BI)

Always

Below 1 Ω

B8-2 (SO) - B9-5 (SI)

Always

Below 1 Ω

B8-3 (EO) - B9-6 (EI)

Always

Below 1 Ω

B8-1 (BO) or B9-4 (BI) - Body ground

Always

10 kΩ or higher

B8-2 (SO) or B9-5 (SI) - Body ground

Always

10 kΩ or higher

B8-3 (EO) or B9-6 (EI) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE WIRE HARNESS OR CONNECTOR

OK

7.

REPLACE FRONT CENTER ULTRASONIC SENSOR RH

(a) Replace the front center ultrasonic sensor RH with a new or normally functioning one.

Click here 2021 - 2024 MY Camry HV [10/2020 -        ]; PARK ASSIST / MONITORING: ULTRASONIC SENSOR (for Front): REMOVAL

HINT:

To check if the ultrasonic sensor is functioning correctly, replace it with another ultrasonic sensor.

NEXT

8.

RECHECK FOR DTC

(a) According to the display on the GTS, check for DTCs.

Body Electrical > Clearance Warning > Trouble Codes

(b) According to the display on the GTS, clear the DTCs.

Body Electrical > Clearance Warning > Clear DTCs

(c) Recheck for DTCs.

Body Electrical > Clearance Warning > Trouble Codes

Result

Proceed to

No DTC is output

A

"C1AE387" is output

B

A

END (FRONT CENTER ULTRASONIC SENSOR RH WAS DEFECTIVE)

B

REPLACE CLEARANCE WARNING ECU ASSEMBLY