Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM100000001T5FX
Model Year Start: 2021 Model: Camry HV Prod Date Range: [10/2020 -           ]
Title: AUDIO / VIDEO: AMPLIFIER ANTENNA: REMOVAL; 2021 - 2024 MY Camry HV [10/2020 -        ]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during amplifier antenna assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedures

Effect/Inoperative Function when Necessary Procedure not Performed

Link

Disconnect cable from negative auxiliary battery terminal

Perform steering sensor zero point calibration

Lane Tracing Assist System

2021 - 2024 MY Camry HV [10/2020 -        ]; PRE-COLLISION: PRE-COLLISION SYSTEM: INITIALIZATION

Pre-collision System

Lighting System (w/ AFS)(EXT)

Memorize steering angle neutral point

Parking Assist Monitor System

2018 - 2024 MY Camry HV [07/2017 -        ]; PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM: INITIALIZATION

Panoramic View Monitor System

2021 - 2024 MY Camry HV [10/2020 -        ]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM: INITIALIZATION

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click here 2021 - 2022 MY Camry HV [10/2020 - 08/2022]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: PRECAUTION 2023 - 2024 MY Camry HV [08/2022 -        ]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: PRECAUTION

PROCEDURE

1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click here 2020 - 2024 MY Camry HV [09/2019 -        ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION

2. REMOVE LUGGAGE TRIM SERVICE HOLE COVER

Click here 2021 - 2024 MY Camry HV [10/2020 -        ]; MAINTENANCE: AUXILIARY BATTERY: REMOVAL+

3. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Click here 2021 - 2024 MY Camry HV [10/2020 -        ]; MAINTENANCE: AUXILIARY BATTERY: REMOVAL+

CAUTION:

  • Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
  • If an airbag deploys for any reason, it may cause a serious injury.

4. REMOVE REAR SEAT CUSHION ASSEMBLY

Click here 2021 - 2024 MY Camry HV [10/2020 -        ]; SEAT: REAR SEAT ASSEMBLY: REMOVAL+

5. REMOVE REAR SEAT CUSHION LOCK HOOK

Click here 2021 - 2024 MY Camry HV [10/2020 -        ]; SEAT: REAR SEAT ASSEMBLY: REMOVAL+

6. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH

Click here 2021 - 2024 MY Camry HV [10/2020 -        ]; SEAT: REAR SEAT ASSEMBLY: REMOVAL+

7. REMOVE REAR SIDE SEATBACK ASSEMBLY LH

Click here 2021 - 2024 MY Camry HV [10/2020 -        ]; SEAT: REAR SEAT ASSEMBLY: REMOVAL+

8. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure as for the LH side.

9. REMOVE REAR SIDE SEATBACK ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.

10. REMOVE INNER ROOF SIDE GARNISH LH

Click here 2021 MY Camry HV [10/2020 - 08/2021]; INTERIOR PANELS / TRIM: ROOF HEADLINING: REMOVAL+ 2022 - 2024 MY Camry HV [08/2021 -        ]; INTERIOR PANELS / TRIM: ROOF HEADLINING: REMOVAL+

11. REMOVE INNER ROOF SIDE GARNISH RH

HINT:

Use the same procedure as for the LH side.

12. REMOVE NO. 2 AMPLIFIER ANTENNA ASSEMBLY

(a) Disconnect the 2 connectors.

(b) Remove the bolt.

(c) Disengage the 2 guides to remove the No. 2 amplifier antenna assembly.

13. REMOVE NO. 1 AMPLIFIER ANTENNA ASSEMBLY

HINT:

Use the same procedure as for the No. 2 amplifier antenna assembly.

14. REMOVE ANTENNA CORD SUB-ASSEMBLY

(a) Disconnect the connector to remove the antenna cord sub-assembly.

HINT:

Use the same procedure for the RH side and LH side.